Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356689 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1422  Master Cylinder Pressure Sensor Zero Point High Malfunction  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
C1422 When vehicle speed is 3 km/h (2 mph) or more and stop light switch assembly is OFF, master cylinder pressure continuously exceeds 1.764 MPa (18.0 kgf/cm2, 255 psi) for 5 seconds or more.
·

STOP NO. 1 fuse

·

STOP NO. 5 fuse

·

Stop light switch assembly

·

Skid control ECU (Brake actuator assembly)

·

Brake actuator assembly (Master cylinder pressure sensor)

·

Wire harness or connector



WIRING DIAGRAM

C373477E01
0.031,0.927 0.875,1.167 0.844,0.24 10 false from Battery 1.229,1.094 2.198,1.344 0.969,0.25 10 false STOP NO. 1 2.156,1.49 4.021,1.74 1.865,0.25 10 false Stop Light Switch Assembly 2.167,1.323 2.479,1.563 0.313,0.24 10 false H1 0.75,2.063 2.135,2.313 1.385,0.25 10 false to Stop Light Circuit 2.802,2.229 3.771,2.479 0.969,0.25 10 false STOP NO. 2 4.219,1.104 5.104,1.344 0.885,0.24 10 false STOP NO. 5 5.26,0.927 5.646,1.125 0.385,0.198 10 false STP 5.26,2.156 5.708,2.417 0.448,0.26 10 false GND1 5.177,2.917 5.5,3.146 0.323,0.229 10 false A71 5.177,3.115 6.76,3.51 1.583,0.396 10 false Skid Control ECU (Brake Actuator Assembly) 2.208,0.802 2.427,1.021 0.219,0.219 10 false 1 3.323,0.781 3.51,1.01 0.188,0.229 10 false 2 4.969,0.792 5.25,1 0.281,0.208 10 false 35 4.99,2.042 5.271,2.25 0.281,0.208 10 false 25

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.



Result:
Result Proceed to
DTC C1422 is output A
DTCs C1422 and C1425 are output B



A

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

B

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

In accordance with the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


f.

Check that the stop light switch assembly condition observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)

NG

5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
3.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

In accordance with the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Master Cylinder Pressure Master cylinder pressure sensor pressure / Min.: 0.00 MPa, Max.: 24.48 MPa Brake pedal operated: Proportional to pedal force
Brake pedal released: 0.00 to 1.76 MPa
-

OK:

Data List pressure is within standard range.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

4.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.


e.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1422 is not output A
DTC C1422 is output B




A

B

5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch assembly installation (Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (w/ Brake pedal Load Sensing Switch)>INSTALLATION).

OK:

The brake pedal height and stop light switch assembly installation are normal.



Result:
Proceed to
OK
NG



OK

6.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY

6.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Remove the stop light switch assembly (Click hereVehicle Interior>LIGHTING>STOP LIGHT SWITCH>REMOVAL).


b.

Inspect the stop light switch assembly (Click hereVehicle Interior>LIGHTING>STOP LIGHT SWITCH>INSPECTION).

OK:

The stop light switch assembly is normal.



Result:
Proceed to
OK
NG



OK

7.CHECK TERMINAL VOLTAGE (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

7.CHECK TERMINAL VOLTAGE (STP TERMINAL)
a.
C399804E04
1.531,0.135 1.885,0.365 0.354,0.229 1.885,1.833 2.219,1.292 true 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 1.75,1.885 2.146,2.073 0.396,0.188 10 false STP 1.594,0.167 1.979,0.406 0.385,0.24 10 false A71

Turn the ignition switch off.


b.

Reinstall the stop light switch assembly (Click hereVehicle Interior>LIGHTING>STOP LIGHT SWITCH>INSTALLATION).


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the A71 skid control ECU (brake actuator assembly) connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A71-35 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
A71-35 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)