Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  C1403  Rear Speed Sensor RH Malfunction  C1404  Rear Speed Sensor LH Malfunction  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for brake control.

The speed sensor generates vehicle speed pulses based on the rotation of the skid control rotor. The skid control ECU (brake actuator assembly) detects the speed of each wheel using this vehicle speed pulse.

HINT:

When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.


C371022E02
0.938,0.563 1.302,1.031 true 1.927,1.906 2.281,2.344 true 0.792,0.427 1.104,0.625 0.313,0.198 10 false *1 2.323,2.344 2.635,2.542 0.313,0.198 10 false *2 4.875,0.417 5.188,0.615 0.313,0.198 10 false *a 4.292,1.5 4.604,1.698 0.313,0.198 10 false *b 5.313,1.5 5.625,1.698 0.313,0.198 10 false *c 6.167,0.698 6.646,0.896 0.479,0.198 10 false 1.4 V 6.198,1.115 6.667,1.302 0.469,0.188 10 false 0.7 V

Text in Illustration
*1 Rear Speed Sensor *2 Rear Skid Control Rotor
*a Waveform (Reference):
Between Speed Sensor (-) and Body Ground
*b Low speed
*c High speed - -

DTC No. DTC Detection Condition Trouble Area
C1403
C1404
Either of the following is detected:
1.

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.

2.

At a vehicle speed less than 10 km/h (6 mph), output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

At a vehicle speed less than 10 km/h (6 mph), outputs from both speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except both rear speed sensors are 0 km/h (0 mph))


·

Rear speed sensor RH/LH

·

Sensor installation

·

Rear skid control rotor RH/LH



HINT:
·

DTC C1403 is for the rear speed sensor RH.

·

DTC C1404 is for the rear speed sensor LH.



WIRING DIAGRAM

C372198E01
3.875,1.25 4.063,1.448 0.188,0.198 10 false 1 1.552,0.698 1.74,0.896 0.188,0.198 10 false 1 1.531,2.281 1.719,2.479 0.188,0.198 10 false 1 1.552,1.24 1.74,1.438 0.188,0.198 10 false 3 1.542,2.833 1.729,3.031 0.188,0.198 10 false 3 3.885,0.708 4.073,0.906 0.188,0.198 10 false 5 3.885,2.26 4.073,2.458 0.188,0.198 10 false 8 3.885,2.823 4.073,3.021 0.188,0.198 10 false 4 5.177,1.26 5.448,1.448 0.271,0.188 10 false 15 5.167,0.729 5.438,0.917 0.271,0.188 10 false 16 5.156,2.271 5.427,2.458 0.271,0.188 10 false 29 5.167,2.844 5.438,3.031 0.271,0.188 10 false 28 1.167,0.833 1.531,1.042 0.365,0.208 10 false RR+ 5.427,0.823 5.792,1.031 0.365,0.208 10 false RR+ 1.208,1.365 1.573,1.573 0.365,0.208 10 false RR- 5.438,1.365 5.802,1.573 0.365,0.208 10 false RR- 1.188,2.396 1.552,2.604 0.365,0.208 10 false RL+ 5.438,2.385 5.802,2.594 0.365,0.208 10 false RL+ 1.208,2.969 1.573,3.177 0.365,0.208 10 false RL- 5.427,2.938 5.792,3.146 0.365,0.208 10 false RL- 2.75,3.208 3.135,3.417 0.385,0.208 10 false Pp1 0.49,1.844 2.031,2.052 1.542,0.208 10 false Rear Speed Sensor RH 0.563,3.417 2.115,3.625 1.552,0.208 10 false Rear Speed Sensor LH 0.51,1.615 0.875,1.823 0.365,0.208 10 false p4 0.563,3.208 0.927,3.417 0.365,0.208 10 false p3 2.75,3.427 4.531,3.646 1.781,0.219 10 false Skid Control Sensor Wire 5.219,3.281 5.604,3.49 0.385,0.208 10 false A71 5.229,3.5 6.75,3.885 1.521,0.385 10 false Skid Control ECU (Brake Actuator Assembly)

PROCEDURE

1.CHECK REAR SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C168336E28
0.792,0.396 1.104,0.594 0.313,0.198 10 false *a 2.385,0.396 2.698,0.594 0.313,0.198 10 false *b 2,1.656 2.313,1.854 0.313,0.198 10 false *c

Check the speed sensor installation (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR (w/ Brake pedal Load Sensing Switch)>INSTALLATION).

OK:

There is no clearance between the sensor and the rear axle housing.

The installation bolt is tightened properly.


Text in Illustration
*a Normal
*b Abnormal
*c Clearance


Result:
Proceed to
OK
NG



OK

2.INSPECT REAR SPEED SENSOR TIP

NG

2.INSPECT REAR SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

No scratches, oil, or foreign matter on the sensor tip.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.




Result:
Proceed to
OK
NG



OK

3.INSPECT REAR SKID CONTROL ROTOR

NG

CLEAN OR REPLACE REAR SPEED SENSOR

3.INSPECT REAR SKID CONTROL ROTOR

b.

Check the rear skid control rotor.

OK:

No scratches, oil or foreign matter on the rotor.


NOTICE:

Check the speed sensor signal after cleaning or replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>TEST MODE PROCEDURE).




Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (REAR SPEED SENSOR)

NG

CLEAN OR REPLACE REAR SKID CONTROL ROTOR

4.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations


g.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>PROBLEM SYMPTOMS TABLE).



Result:
Proceed to
OK
NG



OK

NG

5.REPLACE REAR SPEED SENSOR
5.REPLACE REAR SPEED SENSOR
a.

Turn the ignition switch off.



Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1403 and C1404 are not output A
DTCs C1403 and/or C1404 are output B


NOTICE:

Check the speed sensor signal after replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>TEST MODE PROCEDURE).




A

END

B