Steering angle sensor signals are input to the skid control ECU (brake actuator assembly) via the CAN communication system.
When a malfunction occurs in the communication line to the steering angle sensor, U0126 is output. If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.
DTCs may be stored if one of the following occurs:
Steering angle sensor zero point malfunction
Steering angle sensor signal malfunction
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1434 | Normal communication between the skid control ECU and the steering angle sensor and abnormal steering angle sensor zero point. | ·
ECU-B NO. 3 fuse ·
ECU-IG1 NO. 3 fuse ·
Steering angle sensor (Spiral with sensor cable sub-assembly) ·
Skid control ECU (Brake actuator assembly) ·
Wire harness or connector |
Refer to DTC C1432 (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>C1432).
Do not remove the steering angle sensor from the spiral with sensor cable subassembly.
When replacing the steering angle sensor (spiral with sensor cable sub-assembly), confirm that the replacement part is of the correct specification.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When U0073, U0124 and/or U0126 is output together with C1434, inspect and repair the trouble areas indicated by U0073, U0124 and/or U0126 first (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>U0073).
When any of the speed sensors or the yaw rate and acceleration sensor (yaw rate sensor)*1 or yaw rate and acceleration sensor (airbag ECU assembly)*2 has trouble, DTCs for the steering angle sensor (spiral with sensor cable subassembly) may be output even when the steering angle sensor (spiral with sensor cable sub-assembly) is normal. When DTCs for the speed sensors or yaw rate and acceleration sensor (yaw rate sensor)*1 or yaw rate and acceleration sensor (airbag ECU assembly)*2 are output together with DTCs for the steering angle sensor (spiral with sensor cable sub-assembly), inspect and repair the speed sensor and yaw rate and acceleration sensor (yaw rate sensor)*1 or yaw rate and acceleration sensor (airbag ECU assembly)*2 first, and then inspect and repair the steering angle sensor (spiral with sensor cable sub-assembly).
*1: w/o Airbag System
*2: w/ Airbag System
Turn the ignition switch off.
Turn the ignition switch to ON again and check that no CAN communication system DTC is output (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).
Start the engine.
Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left to check that no speed sensor or yaw rate and acceleration sensor DTCs are output (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| No CAN communication system, speed sensor, or yaw rate and acceleration sensor DTCs are output | A |
| CAN communication system DTC is output | B |
| Speed sensor or yaw rate and acceleration sensor DTC is output | C |
If there is a malfunction in any of the speed sensors or the yaw rate and acceleration sensor (yaw rate sensor)*1 or yaw rate and acceleration sensor (airbag ECU assembly)*2, an abnormal value may be output although the steering angle sensor (spiral with sensor cable sub-assembly) sensor is normal.
If speed sensor and yaw rate and acceleration sensor (yaw rate sensor)*1 or yaw rate and acceleration sensor (airbag ECU assembly)*2 DTCs are output simultaneously, repair these two sensors first and inspect the steering angle sensor (spiral with sensor cable sub-assembly).
*1: w/o Airbag System
*2: w/ Airbag System
A
B
C
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG