Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch) › 2017.01–2021.01
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356879 ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch)  C1265/65  Vacuum Sensor Malfunction  C1285/85  Vacuum Sensor Output Malfunction (Test Mode DTC)  


DESCRIPTION

DTC C1285/85 can be deleted when the vacuum sensor sends a vacuum signal or the Test Mode ends.

DTC C1285/85 is output only in the Test Mode.

DTC Code DTC Detection Condition Trouble Area
C1265/65 When any of the following is detected:
1.

When IG1 terminal voltage is 9.5 to 18.5 V, VCM terminal voltage is not between 4.7 and 5.3 V for 1.2 seconds or more.

2.

Either PIM or PIM2 terminal voltage is not between 0.4 and 4.5 V for 1.2 seconds or more.

3.

After the stop light switch is turned off with PMC terminal voltage 1 V or more, either PIM or PIM2 terminal voltage does not change by 0.01 V in 1 second.

4.

Noise occurs in either PIM or PIM2 terminal voltage at least 7 times for 5 seconds.

5.

Difference between PIM and PIM2 terminal voltages is 344 mV or more for 10 seconds or more.


·

Vacuum sensor

·

Vacuum sensor circuit

·

Skid control ECU


C1285/85 Detected only during Test Mode. Vacuum sensor

WIRING DIAGRAM

C375103E01
1.177,0.958 1.49,1.156 0.313,0.198 10 false E3 1.104,1.438 1.49,1.667 0.385,0.229 10 false PIM 1.073,1.99 1.479,2.198 0.406,0.208 10 false VCP 0.323,2.802 0.635,3 0.313,0.198 10 false F12 0.323,2.979 1.885,3.229 1.563,0.25 10 false No. 1 Vacuum Sensor 1.531,0.833 1.844,1.031 0.313,0.198 10 false 1 1.521,1.354 1.833,1.552 0.313,0.198 10 false 2 1.521,1.865 1.833,2.063 0.313,0.198 10 false 3 3.281,2.615 3.948,2.823 0.667,0.208 10 false Shielded 5.833,0.729 6.146,0.927 0.313,0.198 10 false 7 5.75,0.958 6.063,1.156 0.313,0.198 10 false A48 6.167,0.948 6.479,1.146 0.313,0.198 10 false E3 6.167,1.448 6.552,1.667 0.385,0.219 10 false PIM 6.177,1.958 6.563,2.198 0.385,0.24 10 false VCP 6.177,2.469 6.542,2.677 0.365,0.208 10 false VSS 5.833,2.24 6.146,2.438 0.313,0.198 10 false 8 5.844,1.75 6.156,1.948 0.313,0.198 10 false 5 5.844,1.229 6.156,1.427 0.313,0.198 10 false 6 1.188,4.146 1.5,4.344 0.313,0.198 10 false E4 1.042,4.635 1.479,4.844 0.438,0.208 10 false PIM2 0.99,5.146 1.479,5.385 0.49,0.24 10 false VCP2 1.531,4.01 1.844,4.208 0.313,0.198 10 false 1 1.542,4.51 1.854,4.708 0.313,0.198 10 false 2 1.542,5.042 1.854,5.24 0.313,0.198 10 false 3 0.333,5.948 0.646,6.146 0.313,0.198 10 false F13 0.333,6.135 1.844,6.344 1.51,0.208 10 false No. 2 Vacuum Sensor 0.344,6.667 1.177,6.958 0.833,0.292 10 false from Battery 1.99,6.844 2.844,7.073 0.854,0.229 10 false STOP NO. 1 3.031,6.573 3.344,6.771 0.313,0.198 10 false 1 3.177,7.188 3.49,7.385 0.313,0.198 10 false H1 3.167,7.375 4.563,7.625 1.396,0.25 10 false Stop Light Switch 4.531,6.573 4.844,6.771 0.313,0.198 10 false 2 4.771,6.865 5.656,7.094 0.885,0.229 10 false STOP NO. 5 5.844,6.479 6.156,6.677 0.313,0.198 10 false 9 5.75,6.688 6.063,6.885 0.313,0.198 10 false A50 6.156,6.667 6.531,6.917 0.375,0.25 10 false STP 5.938,7.323 7.063,7.573 1.125,0.25 10 false Skid Control ECU 6.177,5.646 6.667,5.844 0.49,0.198 10 false VSS2 6.177,5.146 6.646,5.375 0.469,0.229 10 false VCP2 6.167,4.646 6.635,4.865 0.469,0.219 10 false PIM2 6.167,4.135 6.479,4.333 0.313,0.198 10 false E4 5.781,3.885 6.094,4.083 0.313,0.198 10 false 15 5.792,4.417 6.104,4.615 0.313,0.198 10 false 14 5.792,4.917 6.104,5.115 0.313,0.198 10 false 13 5.792,5.417 6.104,5.615 0.313,0.198 10 false 16 3.281,5.781 4.01,5.979 0.729,0.198 10 false Shielded 5.75,1.469 6.063,1.667 0.313,0.198 10 false A48 5.75,1.958 6.063,2.156 0.313,0.198 10 false A48 5.75,2.458 6.063,2.656 0.313,0.198 10 false A48 5.75,4.135 6.063,4.333 0.313,0.198 10 false A48 5.75,4.635 6.063,4.833 0.313,0.198 10 false A48 5.74,5.125 6.052,5.323 0.313,0.198 10 false A48 5.75,5.635 6.063,5.833 0.313,0.198 10 false A48

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop light comes on when the brake pedal is depressed, and goes off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed ON
Brake pedal released OFF



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (STOP LIGHT SWITCH)

NG

INSPECT STOP LIGHT CIRCUIT

2.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Data List mode on the GTS (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>DATA LIST / ACTIVE TEST).

ABS / VSC / TRC:
Tester Display Measurement/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-



d.

Check that the stop light condition observed on the GTS changes when the brake pedal is depressed.

OK:

When the brake pedal is depressed, the GTS displays "ON".



Result:
Proceed to
OK
NG



OK

3.CHECK VACUUM HOSE

NG

8.INSPECT SKID CONTROL ECU (STP TERMINAL)
3.CHECK VACUUM HOSE
a.

Turn the ignition switch off.


b.

Check the vacuum hose.

OK:

No cracks or damage on the vacuum hoses.



Result:
Proceed to
OK
NG



OK

4.INSPECT VACUUM SENSOR

NG

REPLACE VACUUM HOSE

4.INSPECT VACUUM SENSOR

OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VACUUM SENSOR)

NG

REPLACE VACUUM SENSOR

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VACUUM SENSOR)
a.

Install the vacuum sensor.


b.

Disconnect the skid control ECU connector.


c.

Disconnect the vacuum sensor connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A48-7 (E3) - F12-1 (E3) Always Below 1 Ω
A48-7 (E3) - Body ground Always 10 kΩ or higher
A48-6 (PIM) - F12-2 (PIM) Always Below 1 Ω
A48-6 (PIM) - Body ground Always 10 kΩ or higher
A48-5 (VCP) - F12-3 (VCP) Always Below 1 Ω
A48-5 (VCP) - Body ground Always 10 kΩ or higher
A48-15 (E4) - F13-1 (E4) Always Below 1 Ω
A48-15 (E4) - Body ground Always 10 kΩ or higher
A48-14 (PIM2) - F13-2 (PIM2) Always Below 1 Ω
A48-14 (PIM2) - Body ground Always 10 kΩ or higher
A48-13 (VCP2) - F13-3 (VCP2) Always Below 1 Ω
A48-13 (VCP2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT SKID CONTROL ECU (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT SKID CONTROL ECU (SENSOR INPUT)
a.
C215678E10
1.354,0.948 1.781,1.198 0.427,0.25 1.188,2.198 1.521,1.635 true 2.042,2.219 1.521,1.521 true 0.156,0.094 0.396,0.313 0.24,0.219 10 false *a 1.448,0.99 1.854,1.188 0.406,0.198 10 false A48 0.844,2.26 1.615,2.49 0.771,0.229 10 false 13 (VCP2) 1.865,2.271 2.542,2.49 0.677,0.219 10 false 5 (VCP)

Reconnect the skid control ECU connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A48-5 (VCP) - Body ground Ignition switch ON 4.75 to 5.25 V
A48-13 (VCP2) - Body ground Ignition switch ON 4.75 to 5.25 V

Text in Illustration
*a Component with harness connected
(Skid Control ECU)



Result:
Proceed to
OK
NG



OK

7.RECONFIRM DTC

NG

REPLACE SKID CONTROL ECU

7.RECONFIRM DTC
a.

Reconnect the vacuum sensor connectors.



c.

At a speed of 10 km/h (6 mph) or more, drive the vehicle and perform braking test (decelerate the vehicle by depressing the brake pedal).


d.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC (C1265/65) is not output A
DTC (C1265/65) is output B


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>PROBLEM SYMPTOMS TABLE).




A

B

REPLACE SKID CONTROL ECU

8.INSPECT SKID CONTROL ECU (STP TERMINAL)
a.

Turn the ignition switch off.


C215683E07
1.521,0.865 1.906,1.094 0.385,0.229 2.156,1.563 2.385,0.74 2.385,0.74 2.521,0.74 true 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 1.604,0.896 1.917,1.094 0.313,0.198 10 false A50 2.615,0.656 3.021,0.906 0.406,0.25 10 false STP

b.

Disconnect the skid control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A50-9 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 8 to 14 V
A50-9 (STP) - Body ground Stop light switch OFF (Brake pedal released) Below 2 V

Text in Illustration
*a Component with harness connected
(Skid Control ECU)


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>PROBLEM SYMPTOMS TABLE).



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)