Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0340  Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)  P0341  Camshaft Position Sensor "A" Circuit Range / Performance (Bank 1 or Single Sensor)  


DESCRIPTION

The camshaft position sensor consists of a magnet and an iron core which is wrapped with copper wire, and is installed on the cylinder head. When the camshaft rotates, each of the 3 teeth on the camshaft pass through the camshaft position sensor. This activates the internal magnet in the sensor, generating a voltage in the copper wire. The camshaft rotation is synchronized with the crankshaft rotation. When the crankshaft turns twice, the voltage is generated 3 times in the camshaft position sensor. The generated voltage in the sensor acts as a signal, allowing the ECM to locate the camshaft position. This signal is then used to control ignition timing, fuel injection timing, and the VVT system.

DTC No. DTC Detection Condition Suspected Area
P0340
·

No camshaft position sensor signal to ECM during cranking (1 trip detection logic)

·

No camshaft position sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic)


·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Camshaft timing gear

·

Jumped tooth of timing chain

·

ECM


P0341 While crankshaft rotates twice, camshaft position sensor signal is input to ECM 12 times or more (1 trip detection logic)
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Camshaft timing gear

·

Jumped tooth of timing chain

·

ECM



HINT:
·
A430117E02
2.781,0.573 3.177,0.76 0.396,0.188 10 false GND 2.76,1.375 3.125,1.563 0.365,0.188 10 false GND 0.281,0.573 0.5,0.729 0.219,0.156 10 false G2 0.281,1.385 0.51,1.531 0.229,0.146 10 false NE 1.281,1.875 2.104,2.052 0.823,0.177 10 false 20 ms./DIV. 2.656,0.094 3.26,0.292 0.604,0.198 10 false 5 V/DIV.

Reference: Inspection using an oscilloscope.

·

DTC P0340 indicates a malfunction related to the camshaft position sensor (+) circuit (the wire harness between the ECM and camshaft position sensor, and the camshaft position sensor itself).

·

DTC P0341 indicates a malfunction related to the camshaft position sensor (-) circuit (the wire harness between the ECM and camshaft position sensor, and the camshaft position sensor itself).


Tester Connection Tool Setting Condition Specified Condition
B73-27 (NE+) - B73-34 (NE-) 5 V/DIV, 20 msec./DIV. Idling The correct waveform is as shown
B73-26 (G2) - B73-34 (NE-) 5 V/DIV, 20 msec./DIV. Idling The correct waveform is as shown


MONITOR DESCRIPTION

If there is no signal from the VVT sensor even though the engine is running, or if the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

This monitor runs for 10 seconds (the first 10 seconds of engine idle) after the engine is started.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT CAMSHAFT POSITION SENSOR (RESISTANCE)
a.

Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance of the wire harness side connectors.

Standard Resistance:
Tester Connection Condition Specified Condition
B71-1 (G2 )- B73-26 (G2+) Always Below 1 Ω
B71-2 (G2) - B73-34 (NE-) Always Below 1 Ω
B71-1 (G2) or B73-26 (G2+) - Body ground Always 10 kΩ or higher
B71-2 (G2) or B73-34 (NE-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT CAMSHAFT POSITION SENSOR (INSTALLATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT CAMSHAFT POSITION SENSOR (INSTALLATION)
a.
A385403E05
0.49,1.781 0.802,1.979 0.313,0.198 10 false OK 2.646,1.781 2.958,1.979 0.313,0.198 10 false NG

Check that the sensor is installed correctly.

OK:

Sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.INSPECT CAMSHAFT

NG

SECURELY REINSTALL CAMSHAFT POSITION SENSOR

4.INSPECT CAMSHAFT
a.

Check that the teeth of the camshaft do not have any cracks or deformation.

OK:

Teeth do not have cracks or deformation.



Result:
Proceed to
OK
NG



OK

NG