Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P2121  Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance  


DESCRIPTION

HINT:

This DTC is related to the accelerator pedal position sensor.


Refer to DTC P2120 (Click here Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>P2120).

DTC No. DTC Detection Condition Suspected Area
P2121 Either of following conditions 1 or 2 met for 0.5 seconds:
(1 trip detection logic)
1.

Difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V. (learned value of accelerator off position)

2.

Difference between VPA and VPA2 is greater than or equal to the specified value.


·

Accelerator pedal position sensor

·

ECM



MONITOR DESCRIPTION

The accelerator pedal position sensor is mounted on the accelerator pedal bracket. The accelerator pedal position sensor has 2 sensor elements and 2 signal outputs: VPA and VPA2. VPA is used to detect the actual accelerator pedal angle (used for engine control) and VPA2 is used to detect malfunctions in VPA. When the difference between the output voltages of VPA and VPA2 deviates from the standard, the ECM determines that the accelerator pedal position sensor is malfunctioning. The ECM turns on the MIL and stores the DTC.

FAIL-SAFE

The accelerator pedal position sensor has a main circuit and associated circuit. When one circuit is malfunctioning, the accelerator pedal position is calculated by the output of the other circuit. When both of the circuits are malfunctioning, it is interpreted that the accelerator pedal is released. As a result, the throttle valve is closed and the engine idles.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2121)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS ON.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result:
Result Proceed to
DTC P2121 is output A
DTC P2121 and other DTCs are output B


HINT:

If any other DTCs besides P2121 are output, perform troubleshooting for those DTCs first.




A

2.READ VALUE USING GTS (ACCELERATOR POSITION NO. 1, ACCELERATOR POSITION NO. 2)

B

2.READ VALUE USING GTS (ACCELERATOR POSITION NO. 1, ACCELERATOR POSITION NO. 2)
a.
A208621E08
0.688,1.781 1.156,1.958 0.469,0.177 10 false *a 2.604,1.781 3.052,1.958 0.448,0.177 10 false *b

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.


d.

Read the values.

Standard Voltage:
Accelerator Pedal Accelerator Position No. 1 Accelerator Position No. 2
Released 0.5 to 1.1 V 1.3 to 1.9 V
Depressed 2.5 to 4.6 V 3.5 to 5.0 V


Text in Illustration
*a Depressed
*b Released


Result:
Proceed to
OK
NG



OK

NG

3.REPLACE ACCELERATOR PEDAL ASSEMBLY
3.REPLACE ACCELERATOR PEDAL ASSEMBLY
a.

Replace the accelerator pedal assembly (Click here Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the tester ON.



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch to ON and turn the tester on.


f.

Wait for 5 seconds after turning the ignition switch to ON.


g.

Check that 20 seconds or more have elapsed since the ignition switch was turned to ON.


h.

Operate the accelerator pedal in accordance with the following procedure.

i.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.


ii.

Slowly depressed the accelerator pedal until Accelerator Position No. 1 is approximately 30% and Accelerator Position No. 2 is approximately 46%, then slowly release the accelerator pedal.



i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read DTCs.


Result:
Result Proceed to
DTC P2121 is output A
DTC is not output B



A

B

END