Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM J

2TR-FE ENGINE CONTROL  SFI SYSTEM  Brake Override System  


DESCRIPTION

When the vehicle is being driven with the accelerator pedal depressed, depressing the brake pedal without releasing the accelerator pedal will activate the brake override system to restrict driving torque. The conditions for activating the brake override system as well as the items that are controlled are explained below.

A232420E90
2.115,2.563 3.052,2.781 0.938,0.219 10 false Vehicle Speed 0.438,2.896 1.771,3.094 1.333,0.198 10 false Wheel Speed Sensor 0.438,2.385 1.833,2.604 1.396,0.219 10 false Vehicle Speed Sensor 0.427,1.677 1.542,1.917 1.115,0.24 10 false Stop Light Switch 0.438,0.708 1.573,1.031 1.135,0.323 10 false Accelerator Pedal Position Sensor 1.052,2.656 1.25,2.854 0.198,0.198 10 false or 3.594,0.75 4.021,0.938 0.427,0.188 10 false ECM 5,1.229 7.052,1.635 2.052,0.406 10 false Effective Accelerator Pedal Angle for System Control 2.198,1.823 2.781,2.021 0.583,0.198 10 false ON/OFF 1.875,0.865 3.031,1.229 1.156,0.365 10 false Actual Accelerator Pedal Angle 0.083,0.094 1.625,0.323 1.542,0.229 10 false Brake Override System:

Activation Conditions:
·

Vehicle is running at or above the specified speed.

·

The accelerator pedal is depressed beyond a specified level, and then the brake pedal is depressed.


NOTICE:

The vehicle may not enter the brake override system control due to the relation of the accelerator pedal angle and the vehicle's speed.



Items Controlled:
·

Driving torque is restricted.


HINT:

During brake override system control, the value for the accelerator pedal angle (which is used for engine control) is forcibly reduced to a specified value. For this reason, the value for accelerator pedal angle will be replaced with a specified value regardless of the actual accelerator pedal angle (Accelerator Position No. 1, Accelerator Position No. 2)



Deactivation Conditions:
·

When the Stop Light Switch turns OFF or the actual accelerator pedal angle increases or decreases beyond the specified range.



CAUTION / NOTICE / HINT

Inspection Method

Drive at 10 km/h (6.25 mph), depress the accelerator pedal by 1/2 to 3/4 and keep it in that position. Under these conditions, if the engine speed decreases to 1000 rpm when the brake pedal is depressed, then the brake override system has been activated.


CAUTION:

When carrying out the inspection, use a place where you are able to carry it out safely and also pay close attention to your surroundings.

Also, when driving make absolutely sure that all road traffic laws, such as speed limits, are observed.


HINT:
·

Under normal conditions, the Throttle Sensor Position value changes in response to the Accelerator Position No. 1 value (the values are not equal). For more information on the numerical values, refer to the Data List (Click hereEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST).

·

If the Data List values of Throttle Sensor Position and Accelerator Position No. 1 do not match, and the value of Throttle Sensor Position changes but the value of Accelerator Position No. 1 is constant, this confirms that the brake override system has activated. (Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.)NOTICE:



NOTICE:

The brake override system restricts driving torque if the brake pedal is depressed when driving with the accelerator pedal depressed. If a customer reports experiencing loss of torque after the accelerator and brake pedals have both been intentionally depressed, explain to the customer that this is not a malfunction, and that the customer should avoid depressing both the accelerator and brake pedals at the same time.

Example: While operating the accelerator pedal, the customer uses their left foot to operate the brake pedal.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Utility / All Codes.


d.

Check DTCs.


Result:
Result Proceed to
DTC is not output A
DTC is output B



A

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH AND ST1)

B

GO TO DTC CHART

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH AND ST1)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch and ST1.


d.

Check the Data List indication when the brake pedal is depressed and released.

OK:
Tester Display Condition Specified Condition
Stop Light Switch Brake pedal released OFF
Brake pedal depressed ON
ST1 Brake pedal released OFF
Brake pedal depressed ON



Result:
Proceed to
A
B



A

3.INSPECT BRAKE PEDAL ASSEMBLY

B

INSPECT STOP LIGHT SWITCH ASSEMBLY

3.INSPECT BRAKE PEDAL ASSEMBLY
a.

Inspect and adjust the brake pedal.

HINT:

If the stop light switch turns ON too late, the start of brake override system control may be delayed; if it turns ON too soon, brake override system control may begin too early, so conduct inspection of the brake pedal and stop light switch assembly.



Result:
Proceed to
A
B



A

4.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR PEDAL POSITION SENSOR)

B

REPAIR OR REPLACE BRAKE PEDAL ASSEMBLY

4.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR PEDAL POSITION SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.


d.

Read the value displayed on the tester.

OK:
Tester Display Condition Specified Condition
Accelerator Position No. 1 Accelerator Pedal
Released → Depressed → Released
Values smoothly change following accelerator pedal operation
Accelerator Position No. 2


HINT:

For numerical values of Accelerator Position No. 1 and Accelerator Position No. 2, refer to the Data List (ClickEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST here).



Result:
Proceed to
A
B



A

5.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)

B

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

5.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.


e.

Read the value displayed on the tester.

Standard:
Tester Display Condition Specified Condition
Vehicle Speed Vehicle stopped, engine running 0 km/h (0 mph)
Vehicle running at constant speed between 16.1 to 64.4 km/h (10 to 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



Result:
Proceed to
A
B



A

END

B

GO TO VEHICLE SPEED SENSOR "A"