Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM J

2TR-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The MIL is used to inform the user when the ECM has detected a vehicle malfunction.

By turning the ignition switch to ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground that illuminates the MIL.

Operation of the MIL should be checked visually:

When the ignition switch is first turned to ON, the MIL should illuminate. When the engine is started, the MIL should turn off.

WIRING DIAGRAM

A380767N10
1.281,0.906 1.896,1.104 0.615,0.198 10 false CANH 2.865,0.906 3.479,1.104 0.615,0.198 10 false CA5H 3.927,0.906 4.542,1.104 0.615,0.198 10 false CA4H 5.521,0.906 6.135,1.104 0.615,0.198 10 false CANH 1.292,1.375 1.906,1.573 0.615,0.198 10 false CANL 2.854,1.365 3.469,1.563 0.615,0.198 10 false CA5L 3.927,1.375 4.542,1.573 0.615,0.198 10 false CA4L 5.521,1.365 6.135,1.563 0.615,0.198 10 false CAN- 1.75,0.75 2.292,0.927 0.542,0.177 10 false 23 2.615,0.75 3.156,0.927 0.542,0.177 10 false 15 5.281,0.76 5.823,0.938 0.542,0.177 10 false 33 4.396,0.75 4.938,0.927 0.542,0.177 10 false 18 2.615,1.208 3.156,1.385 0.542,0.177 10 false 16 1.74,1.208 2.281,1.385 0.542,0.177 10 false 22 4.396,1.208 4.938,1.385 0.542,0.177 10 false 17 5.302,1.208 5.844,1.385 0.542,0.177 10 false 34 4.458,1.979 5.396,2.229 0.938,0.25 10 false to Other ECUs 1.802,1.99 2.74,2.24 0.938,0.25 10 false to Other ECUs 0.063,2.469 0.958,2.635 0.896,0.167 10 false J1 0.042,2.646 2.219,3.073 2.177,0.427 10 false Combination Meter Assembly 2.917,2.521 3.813,2.688 0.896,0.167 10 false J51 2.906,2.677 4.729,3.073 1.823,0.396 10 false Network Gateway ECU 6.042,2.542 6.365,2.76 0.323,0.219 10 false A53 6.052,2.708 6.448,2.906 0.396,0.198 10 false ECM 0.927,3.229 2.75,3.625 1.823,0.396 10 false : CAN Communication Line 0.052,0.01 1.344,0.25 1.292,0.24 12 false w/ ABS:

A179542E04
6.052,2.51 6.51,2.708 0.458,0.198 10 false ECM 5.625,1.427 5.792,1.594 0.167,0.167 10 false W 5.323,1.229 5.521,1.417 0.198,0.188 10 false 30 5.271,1.427 5.646,1.646 0.375,0.219 10 false A53 4.76,1.417 5.031,1.625 0.271,0.208 10 false J1 3.042,1.427 3.385,1.635 0.344,0.208 10 false J1 3.073,1.24 3.271,1.417 0.198,0.177 10 false 2 3.417,1.875 4.781,2.094 1.365,0.219 10 false Combination Meter 3.708,1.583 4.083,1.771 0.375,0.188 10 false MIL 1.906,1.573 2.813,1.792 0.906,0.219 10 false METER IG2 0.021,1.427 1.031,1.802 1.01,0.375 10 false From IG2-NO. 2 Relay 0.177,0.125 0.958,0.406 0.781,0.281 12 false w/o ABS: 3.354,1.302 3.729,1.49 0.375,0.188 10 false IG+ 4.302,1.302 4.74,1.49 0.438,0.188 10 false CHK 4.75,1.229 5.021,1.448 0.271,0.219 10 false 24

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of this circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK IF VEHICLE IS EQUIPPED WITH ABS
a.

Confirm the vehicle specifications.


Result:
Result Proceed to
w/ ABS A
w/o ABS B



A

2.CHECK THAT MIL IS ILLUMINATED

B

6.CHECK THAT MIL IS ILLUMINATED
2.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.


Result:
MIL Condition Proceed to
Illuminates → Turns off Ignition switch to ON → engine is started A
Other than above - B



A

CHECK FOR INTERMITTENT PROBLEMS

B

3.CHECK COMMUNICATION BETWEEN GTS AND ECM
3.CHECK COMMUNICATION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the tester and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B



A

4.CHECK WHETHER DTC OUTPUT RECURS

B

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check if any DTCs have been detected. Note down any DTCs.


Result:
Result Proceed to
DTCs are not output A
Any DTCs is output B



A

5.PERFORM ACTIVE TEST USING GTS

B

REPAIR CIRCUIT INDICATED BY OUTPUT

5.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test / Check Engine Indicator.


e.

Check the status of the MIL while performing the Active Test.


Result:
Result Proceed to
Changes A
Does not change B



A

B

6.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.


Result:
MIL Condition Proceed to
Illuminates → Turns off Ignition switch to ON → engine is started A
Other than above - B



A

7.CHECK WHETHER MIL TURNS OFF

B

10.CHECK THAT MIL IS ILLUMINATED
7.CHECK WHETHER MIL TURNS OFF
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Check if any DTCs have been detected. Note down any DTCs.


Result:
Result Proceed to
No DTC detected A
Any DTCs detected B



A

8.CHECK HARNESS AND CONNECTOR (FOR SHORT)

B

8.CHECK HARNESS AND CONNECTOR (FOR SHORT)
A227403E02
1.813,0.625 2.146,0.833 0.333,0.208 1.865,0.646 2.208,0.865 0.344,0.219 10 false A53 0.094,0.073 0.375,0.354 0.281,0.281 10 false *a

a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.


Text in Illustration
*a Rear view of wire harness connector
(to ECM)


Result:
Proceed to
OK
NG



OK

NG

9.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER)
9.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A53-30 (W) - J1-24 (CHK) Always Below 1 Ω
A53-30 (W) or J1-24 (CHK) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the ignition switch is turned to ON.

OK:

MIL is illuminated.



Result:
Proceed to
OK
NG



OK

NG

11.CHECK THAT ENGINE STARTS
11.CHECK THAT ENGINE STARTS
a.

Turn the ignition switch to ON.


b.

Start the engine.

Result:
Result Proceed to
Engine starts A
Engine does not start* B


HINT:

*: The intelligent tester cannot communicate with the ECM.




A

12.INSPECT COMBINATION METER (MIL CIRCUIT)

B

12.INSPECT COMBINATION METER (MIL CIRCUIT)
a.

See the combination meter troubleshooting procedure (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

CHECK AND REPLACE HARNESS OR CONNECTOR (COMBINATION METER - ECM)

NG