The fuel temperature sensor senses the fuel temperature. A thermistor built into the sensor changes its resistance value according to the fuel temperature. The lower the fuel temperature is, the greater the thermistor resistance becomes, and the higher the fuel temperature is, the lower the thermistor resistance becomes (see Fig. 1).
The fuel temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the fuel temperature sensor from terminal THF via resistor R. The resistor R and the fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes in accordance with the fuel temperature, the voltage at terminal THF also changes. Based on this signal, the ECM corrects the pressure control compensation of the injection or supply pump assembly and an error.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0168 | After engine is warmed up, conditions (a), (b) and (c) continue for more than 1 second (1 trip detection logic):
(a) Engine speed: 1000 rpm or more (b) Vehicle speed: 10 km/h (6 mph) or more (c) Fuel temperature: 88°C (190°F) or more |
·
Open or short in fuel temperature sensor circuit ·
Fuel temperature sensor (built into injection or supply pump assembly) ·
ECM |
| P0180 | Open or short in fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic). | ·
Open or short in fuel temperature sensor circuit ·
Fuel temperature sensor (built into injection or supply pump assembly) ·
ECM |
| P0182 | Short in fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic). | ·
Short in fuel temperature sensor circuit ·
Fuel temperature sensor (built into injection or supply pump assembly) ·
ECM |
| P0183 | Open in fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic). | ·
Open in fuel temperature sensor circuit ·
Fuel temperature sensor (built into injection or supply pump assembly) ·
ECM |
When DTC P0180, P0182 or P0183 is detected, check the fuel temperature by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Fuel Temperature.
| Temperature Displayed | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) or more | Short circuit |
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
If DTCs that are related to different systems are output simultaneously while terminal E2 is used as a ground terminal, terminal E2 may have an open circuit.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.
Read the value.
Same value as the actual fuel temperature.
| Temperature Displayed | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 140°C (284°F) or more | B |
| OK (same as actual fuel temperature) | C |
If there is an open circuit, the GTS indicates -40°C (-40°F).
If there is a short circuit, the GTS indicates 140°C (284°F) or more.
A
B
C
Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
Disconnect the fuel temperature sensor connector.
Connect terminals 1 (E2) and 2 (THF) of the wire harness side connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.
Read the value.
140°C (284°F) or more
| *a | Front view of wire harness connector
(to Fuel Temperature Sensor) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fuel temperature sensor connector.
Connect terminals THF and E2 of the ECM connector.
Before checking, do a visual and contact pressure check for the ECM connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.
Read the value.
140°C (284°F) or more
| *a | Component with harness connected
(ECM) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fuel temperature sensor connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.
Read the value.
-40°C (-40°F)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fuel temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the valve(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B105-4 (THF) or B8-2 (THF) - Body ground | Always | 10 kΩ or higher |
| B104-14 (E2) or B8-1 (E2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG