The injector driver assembly has been adopted to drive the injector assembly at high speeds. The injector driver assembly has realized high-speed driving under high fuel pressure conditions through the use of a DC/DC converter sub-assembly that provides a high- voltage, quick-charging system.
The ECM constantly monitors the injector driver assembly and stops the engine if an abnormal condition is detected.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0201 | Open or short in No. 1 injector circuit occurs a certain number of times (1 trip detection logic). | ·
Open or short in injector driver circuit ·
No. 1 injector assembly ·
Injector driver ·
ECM |
| P0202 | Open or short in No. 2 injector circuit occurs a certain number of times (1 trip detection logic). | ·
Open or short in injector driver circuit ·
No. 2 injector assembly ·
Injector driver ·
ECM |
| P0203 | Open or short in No. 3 injector circuit occurs a certain number of times (1 trip detection logic). | ·
Open or short in injector driver circuit ·
No. 3 injector assembly ·
Injector driver ·
ECM |
| P0204 | Open or short in No. 4 injector circuit occurs a certain number of times (1 trip detection logic). | ·
Open or short in injector driver circuit ·
No. 4 injector assembly ·
Injector driver ·
ECM |
| P062D | Inconsistency in the injection waveforms between the injector driver and ECM while the engine is running a certain number of times (1 trip detection logic). | ·
Open or short in injector driver circuit ·
Injector assembly ·
Injector driver ·
ECM |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
After replacing the injector assembly, the ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.
Disconnect the injector driver connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B98-6 (+B) - B95-4 (GND) | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Injector Driver) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the injector driver connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B98-5 (INJ1) - B98-1 (COM1) | 20°C (68°F) | 0.85 to 1.05 Ω |
| B96-4 (INJ2) - B98-2 (COM2) | 20°C (68°F) | 0.85 to 1.05 Ω |
| B96-2 (INJ3) - B98-2 (COM2) | 20°C (68°F) | 0.85 to 1.05 Ω |
| B98-4 (INJ4) - B98-1 (COM1) | 20°C (68°F) | 0.85 to 1.05 Ω |
| *a | Front view of wire harness connector
(to Injector Driver) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the injector driver connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B95-6 (#10) - B105-21 (#1) | Always | Below 1 Ω |
| B95-2 (#20) - B105-22 (#2) | Always | Below 1 Ω |
| B95-1 (#30) - B105-23 (#3) | Always | Below 1 Ω |
| B95-3 (#40) - B105-24 (#4) | Always | Below 1 Ω |
| B96-1 (INJF) - B105-20 (INJF) | Always | Below 1 Ω |
| B95-6 (#10) or B105-21 (#1) - Body ground | Always | 10 kΩ or higher |
| B95-2 (#20) or B105-22 (#2) - Body ground | Always | 10 kΩ or higher |
| B95-1 (#30) or B105-23 (#3) - Body ground | Always | 10 kΩ or higher |
| B95-3 (#40) or B105-24 (#4) - Body ground | Always | 10 kΩ or higher |
| B96-1 (INJF) or B105-20 (INJF) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
While idling the engine, check the waveform of the ECM connectors using an oscilloscope.
| *a | Component with harness connected
(ECM) |
*b | Signal Waveform |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B105-21 (#1) - B102-1 (E1 | Idling with warm engine | Correct waveform appears as shown |
| B105-22 (#2) - B102-1 (E1) | Idling with warm engine | Correct waveform appears as shown |
| B105-23 (#3) - B102-1 (E1) | Idling with warm engine | Correct waveform appears as shown |
| B105-24 (#4) - B102-1 (E1) | Idling with warm engine | Correct waveform appears as shown |
| B105-20 (INJF) - B102-1 (E1) | Idling with warm engine | Correct waveform appears as shown |
| Result | Proceed to |
|---|---|
| #1 to #4 are normal, INJF is abnormal | A |
| #1 to #4 are abnormal, INJF is normal | B |
| #1 to #4 and INJF are normal |
A
B
Inspect the injector assembly (Click hereEngine / Hybrid System>N04C-VL (FUEL)>FUEL INJECTOR>INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG