Home › Engine / Hybrid System › N04C-VL (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073159 N04C-VL ENGINE CONTROL _0357053 ECD SYSTEM C

N04C-VL ENGINE CONTROL  ECD SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The crankshaft position sensor (NE signal) consists of a magnet, iron core and pickup coil.

The crankshaft angle sensor plate has 32 teeth and is installed on the injection pump drive gear. The NE signal sensor generates 32 signals of every engine revolution. The ECM detects the standard crankshaft angle based on the G signal from the camshaft position sensor, and the actual crankshaft angle and the engine speed by the NE signal.

DTC No. DTC Detection Condition Trouble Area
P0335 Either of the following conditions is met (1 trip detection logic):
(a) No crankshaft position sensor signal to ECM while cranking for 4.7 seconds or more
(b) No crankshaft position sensor signal to ECM while engine running after 3 seconds or more elapsed after STA signal is switched from on to off (Engine speed at 600 rpm or more)
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft angle sensor plate

·

ECM


P0339 In conditions (a), (b) and (c), no crankshaft position sensor (NE) signal is input for 0.05 seconds or more (1 trip detection logic).
(a) Engine speed is 1000 rpm or more
(b) NE signal is off
(c) 3 seconds or more has lapsed after STA signal is switched from on to off
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft angle sensor plate

·

ECM



WIRING DIAGRAM

A403469E01
1.25,0.375 1.708,0.573 0.458,0.198 10 false NE+ 1.271,0.885 1.729,1.083 0.458,0.198 10 false NE- 0.313,1.229 0.771,1.427 0.458,0.198 10 false B5 0.313,1.417 2.573,1.615 2.26,0.198 10 false Crankshaft Position Sensor 0.646,3.24 1.521,3.5 0.875,0.26 10 false *: Shielded 2.938,2.438 3.396,2.635 0.458,0.198 10 false VG 2.438,2.99 2.896,3.188 0.458,0.198 10 false k2 2.427,3.177 4.146,3.396 1.719,0.219 10 false Camshaft Position Sensor 4.49,1.302 4.948,1.5 0.458,0.198 10 false * 3.604,2.177 4.063,2.375 0.458,0.198 10 false G1 3.635,2.656 4.094,2.854 0.458,0.198 10 false G- 2.771,2.333 3.229,2.531 0.458,0.198 10 false 3 3.896,2.073 4.354,2.271 0.458,0.198 10 false 1 3.906,2.594 4.365,2.792 0.458,0.198 10 false 2 6.229,3.271 6.688,3.469 0.458,0.198 10 false B103 6.24,3.458 6.698,3.656 0.458,0.198 10 false ECM 6.052,0.385 6.51,0.583 0.458,0.198 10 false NE+ 6.042,0.896 6.5,1.094 0.458,0.198 10 false NE- 6.052,1.656 6.51,1.854 0.458,0.198 10 false VCG 6.052,2.167 6.51,2.365 0.458,0.198 10 false G+ 6.052,2.677 6.51,2.875 0.458,0.198 10 false G- 5.802,2.583 6.26,2.781 0.458,0.198 10 false 14 5.802,2.073 6.26,2.271 0.458,0.198 10 false 13 5.802,1.573 6.26,1.771 0.458,0.198 10 false 15 5.875,0.802 6.333,1 0.458,0.198 10 false 8 5.875,0.292 6.333,0.49 0.458,0.198 10 false 7 1.625,0.292 2.083,0.49 0.458,0.198 10 false 1 1.646,0.792 2.104,0.99 0.458,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.CHECK CRANKSHAFT POSITION SENSOR
a.
A257466E10
2.333,0.24 2.823,0.531 0.49,0.292 2.656,0.958 2.99,1.698 true 2.656,1.042 2.396,2.01 true 2.594,1.042 1.625,1.917 true 2.583,0.969 1.229,1.677 true 2.427,0.302 3.156,0.542 0.729,0.24 10 false B103 0.094,0.052 0.26,0.208 0.167,0.156 10 false *a 0.427,1.979 0.594,2.135 0.167,0.156 10 false *b 1.365,4.104 2.792,4.344 1.427,0.24 10 false 20 ms./DIV. 2.75,2.396 3.427,2.688 0.677,0.292 10 false 5 V/DIV. 0.563,2.646 0.688,2.802 0.125,0.156 10 false G 0.438,3.333 0.667,3.49 0.229,0.156 10 false NE 2.896,2.771 3.25,2.927 0.354,0.156 10 false GND 2.896,3.333 3.25,3.49 0.354,0.156 10 false GND 2.063,2.031 2.563,2.188 0.5,0.156 10 false 13 (G+) 2.667,1.719 3.167,1.875 0.5,0.156 10 false 7 (NE+) 1.323,1.927 1.781,2.083 0.458,0.156 10 false 14 (G-) 0.74,1.625 1.219,1.781 0.479,0.156 10 false 8 (NE-)

While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

Standard:
Tester Connection Condition Specified Condition
B103-7 (NE+) - B103-8 (NE-) Idling Correct waveform appears as shown
B103-13 (G+) - B103-14 (G-) Idling Correct waveform appears as shown


Text in Illustration
*a Component with harness connected
(ECM)
*b G and NE Signal Waveform


Result:
Proceed to
OK
NG



OK

NG

2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
a.

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B5-1 - B103-7 (NE+) Always Below 1 Ω
B5-2 - B103-8 (NE-) Always Below 1 Ω
B5-1 or B103-7 (NE+) - Body ground Always 10 kΩ or higher
B5-2 or B103-8 (NE-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

4.CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)
a.

Check the crankshaft position sensor installation condition.


OK:

The crankshaft position sensor is installed properly.


B519906E01
0.427,0.021 0.74,0.219 0.313,0.198 10 false *a 2.469,0.042 2.781,0.24 0.313,0.198 10 false *b 2.698,1.823 3.01,2.021 0.313,0.198 10 false *c

Text in Illustration
*a OK
*b NG
*c Clearance

Result:
Proceed to
OK
NG



OK

5.CHECK CRANKSHAFT POSITION SENSOR PLATE

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

5.CHECK CRANKSHAFT POSITION SENSOR PLATE
a.

Check the teeth of the crankshaft angle sensor plate.


Result:
Proceed to
OK
NG



OK

NG

REPLACE CRANKSHAFT POSITION SENSOR PLATE