Home › Engine / Hybrid System › N04C-VL (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073159 N04C-VL ENGINE CONTROL _0357053 ECD SYSTEM C

N04C-VL ENGINE CONTROL  ECD SYSTEM  P0500  Vehicle Speed Sensor  


DESCRIPTION

The speedometer sensor outputs a 4-pulse signal every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. After this signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter assembly, it is then transmitted to the ECM. The ECM determines the vehicle speed, based on the frequency of these pulse signals.

A257468E02
2.958,1.896 4.823,2.208 1.865,0.313 10 false Combination Meter Assembly 0.76,2.115 2.125,2.427 1.365,0.313 10 false Speedometer Sensor 5.875,2.125 6.25,2.344 0.375,0.219 10 false ECM 4.771,0.135 5.323,0.375 0.552,0.24 10 false 4-pulse 2.573,0.135 3.125,0.375 0.552,0.24 10 false 4-pulse

DTC No. DTC Detection Condition Trouble Area
P0500 3 seconds or more has elapsed after STA signal is switched from on to off, conditions (a), (b), (c) and (d) are met for 8 seconds or more (2 trip detection logic):
(a) Engine coolant temperature is higher than 70°C (158°F).
(b) Injection volume is 40 mm3/st or more.
(c) No speed signal is input to ECM.
(d) Engine coolant temperature sensor, accelerator pedal position sensor, mass air flow meter sub-assembly, manifold absolute pressure sensor and diesel throttle body assembly are all normal.
·

Open or short in vehicle speed sensor circuit

·

Speedometer sensor

·

Combination meter assembly

·

ECM


3 seconds or more has elapsed after STA signal is switched from on to off, conditions (a) and (b) are met for 5 seconds or more (2 trip detection logic):
(a) Fuel-cut operation is being performed.
(b) No speed signal is input to ECM.

WIRING DIAGRAM

A398539E01
0.635,2.615 0.948,2.813 0.313,0.198 10 false J1 1.74,1.656 2.052,1.854 0.313,0.198 10 false +S 2.042,1.563 2.354,1.76 0.313,0.198 10 false 6 4.958,1.448 5.271,1.646 0.313,0.198 10 false 7 4.885,1.656 5.198,1.854 0.313,0.198 10 false A57 4.854,2.208 5.208,2.406 0.354,0.198 10 false B102 4.979,2.021 5.292,2.219 0.313,0.198 10 false 1 5.302,1.823 5.729,2.01 0.427,0.188 10 false SPD 5.323,2.208 5.635,2.406 0.313,0.198 10 false E1 5.823,2.781 6.24,2.979 0.417,0.198 10 false ECM 0.625,2.813 2.073,3.021 1.448,0.208 10 false Combination Meter

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

Various systems use the vehicle speed signal distributed from the combination meter. Check all the components possibly related to speed signal.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.

HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the procedure described in speedometer malfunction.




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

NG

CHECK METER / GAUGE SYSTEM (SPEEDOMETER MALFUNCTION)

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-7 (SPD) - J1-6 (+S) Always Below 1 Ω
A57-7 (SPD) or J1-6 (+S) - Body ground Always 10 kΩ or higher


HINT:

If the wire has short, check the speed signal circuit in other systems related to the vehicle speed signal.



Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (+S VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (OTHER SYSTEMS RELATED TO SPEED SIGNAL)

3.INSPECT ECM (+S VOLTAGE)
a.
A257469E03
1.51,0.146 1.927,0.406 0.417,0.26 1.26,1.76 1.115,1.177 true 0.073,0.094 0.271,0.292 0.198,0.198 10 false *a 1.625,0.188 1.896,0.344 0.271,0.156 10 false J1 1.208,1.792 1.5,2 0.292,0.208 10 false +S

Disconnect the combination meter assembly connector.

HINT:

Disconnect the ECU connectors on the other systems related to the speed signal (but the ECM connectors must be connected).



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the valve(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J1-6 (+S) - Body ground Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of with harness connector
(to Combination Meter Assembly)


Result:
Proceed to
OK
NG



OK

4.CHECK ECM (SPD VOLTAGE)

NG

4.CHECK ECM (SPD VOLTAGE)
a.
A257470E05
1.563,0.219 1.979,0.479 0.417,0.26 2.271,1.229 1.438,2.167 true 0.156,3.99 0.448,4.167 0.292,0.177 10 false 0 V 0.156,2.844 0.448,3.021 0.292,0.177 10 false 5 V 0.156,0.094 0.333,0.271 0.177,0.177 10 false *a 1.708,0.271 1.99,0.427 0.281,0.156 10 false J1 1.25,2.188 1.469,2.333 0.219,0.146 10 false +S

Move the shift lever to neutral.


b.

Jack up the vehicle.


c.

Turn the ignition switch to ON.


d.

Measure the voltage between the terminal of the combination meter assembly and body ground while the wheel is turned slowly.

Standard Voltage:
Tester Connection Condition Specified Condition
J1-6 (+S) - Body ground Ignition switch ON Turn wheel slowly Generated intermittently


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)

HINT:

The output voltage should fluctuate up and down similarly to the diagram when the wheel is turned slowly.



Result:
Proceed to
OK
NG



OK

NG

CHECK COMBINATION METER ASSEMBLY