Home › Engine / Hybrid System › N04C-VL (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073159 N04C-VL ENGINE CONTROL _0357053 ECD SYSTEM J

N04C-VL ENGINE CONTROL  ECD SYSTEM  Brake Override System  


DESCRIPTION

When the vehicle is being driven with the accelerator pedal depressed, depressing the brake pedal without releasing the accelerator pedal will activate the brake override system to restrict driving torque. The conditions for activating the brake override system as well as the items that are controlled are explained below.

A249321E10
0.125,0.104 2.135,0.531 2.01,0.427 12 false Brake Override System: 0.281,0.802 2.458,1.271 2.177,0.469 10 false Accelerator Pedal Position Sensor 0.271,1.615 2.365,1.979 2.094,0.365 10 false Stop Light Switch Assembly 0.271,2.396 2.354,3.115 2.083,0.719 10 false Vehicle Speed Sensor or Wheel Speed Sensor 4.24,1.854 4.708,2.177 0.469,0.323 10 false ECM 5.594,1.25 6.969,2.302 1.375,1.052 10 false Effective Accelerator Pedal Angle for System Control 3,1.813 3.688,2.167 0.688,0.354 10 false ON/OFF 2.667,1.031 4,1.677 1.333,0.646 10 false Actual Accelerator Pedal Angle 2.771,2.823 3.833,3.25 1.063,0.427 10 false Vehicle Speed

Activation Conditions
·

Vehicle is running at or above the specified speed.

·

The accelerator pedal is depressed beyond a specified level, and then the brake pedal is depressed.


NOTICE:

The vehicle may not enter the brake override system control due to the relation of the accelerator pedal angle and the vehicle's speed.


Items Controlled
·

Driving torque is restricted.


HINT:

During brake override system control, the value for the accelerator pedal angle (which is used for engine control) is forcibly reduced to a specified value. For this reason, the Data List value for Accel Position will be replaced with a specified value regardless of the actual accelerator pedal angle (Accel Sens. No. 1 Volt %, Accel Sens. No. 2 Volt %)


Deactivation Conditions
·

When the Stop Light Switch turns off or the actual accelerator pedal angle increases or decreases beyond the specified range.


CAUTION / NOTICE / HINT

Inspection Method

Drive at 10 km/h (6.25 mph), depress the accelerator pedal by 1/2 to 3/4 and keep it in that position. Under these conditions, if the engine speed decreases to 1000 rpm when the brake pedal is depressed, then the brake override system has been activated.


CAUTION:

When carrying out the inspection, use a place where you are able to carry it out safely and also pay close attention to your surroundings.

Also, when driving make absolutely sure that all road traffic laws, such as speed limits, are observed.


HINT:
·

Under normal conditions, the Accel Position value changes in response to the Accel Sens. No. 1 Volt % value. For more information on the numerical values, refer to the Data List (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>DATA LIST / ACTIVE TEST).

·

If the Data List values of Accel Position and Accel Sens. No. 1 Volt % do not match, and the value of Accel Position changes but the value of Accel Sens. No. 1 Volt % is constant, this confirms that brake override system has activated. (Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.)



NOTICE:

The brake override system restricts driving torque if the brake pedal is depressed when driving with the accelerator pedal depressed. If a customer reports experiencing loss of torque after the accelerator and brake pedals have both been intentionally depressed, explain to the customer that this is not a malfunction, and that the customer should avoid depressing both the accelerator and brake pedals at the same time.

Example: While operating the accelerator pedal, the customer uses their left foot to operate the brake pedal.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check DTCs.


Result:
Result Proceed to
DTC is not output A
DTC is output B



A

2.READ VALUE USING GTS (STOP LIGHT SWITCH)

B

GO TO DTC CHART

2.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.


e.

Check the Data List indication when the brake pedal is depressed and released.

Standard:
GTS Display Condition Specified Condition
Stop Light Switch Brake pedal released OFF
Brake pedal depressed ON



Result:
Proceed to
OK
NG



OK

3.INSPECT BRAKE PEDAL ASSEMBLY

NG

INSPECT STOP LIGHT SWITCH ASSEMBLY

3.INSPECT BRAKE PEDAL ASSEMBLY
a.

Inspect and adjust the brake pedal.

HINT:

If the stop light switch turns on too late, the start of brake override system control may be delayed; if it turns on too soon, brake override system control may begin too early, so conduct inspection of the brake pedal and stop light switch assembly.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR)

NG

REPAIR OR REPLACE BRAKE PEDAL ASSEMBLY

4.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No. 1 Volt % and Accel Sens. No. 2 Volt %.


e.

Read the value displayed on the GTS.

Standard:
GTS Display Condition Specified Condition
Accel Sens. No. 1 Volt % Accelerator PedalReleased → Depressed → Released Values smoothly change following accelerator pedal operation
Accel Sens. No. 2 Volt %


HINT:

For numerical values of Accel Sens. No. 1 Volt % and Accel Sens. No. 2 Volt %, refer to the Data List (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>DATA LIST / ACTIVE TEST).



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (VEHICLE SPEED)

NG

REPLACE ACCELERATOR PEDAL POSITION SENSOR (ACCELERATOR LINK ASSEMBLY)

5.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.


e.

Read the value displayed on the GTS.

Standard:
GTS Display Condition Specified Condition
Vehicle Speed Vehicle stopped, engine running 0 km/h (0 mph)
Vehicle running at constant speed between 16.1 to 64.4 km/h (10 to 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)

NG

6.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.


e.

Read the value displayed on the GTS.

Standard:
GTS Display Condition Specified Condition
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
Vehicle stopped, engine running 0 km/h (0 mph)
Vehicle running at constant speed between 16.1 to 64.4 km/h (10 to 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



Result:
Proceed to
OK
NG



OK

END

NG

INSPECT FRONT OR REAR SPEED SENSOR