Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2017.01–2019.08
RM2850E _58 Vehicle Interior _073141 METER / GAUGE / DISPLAY _0357098 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Engine Coolant Temperature Receiver Gauge Malfunction  


DESCRIPTION

w/ Multi-information Display:

The combination meter assembly receives engine coolant temperature signals from the ECM via the CAN communication line. The combination meter assembly displays an engine coolant temperature that is calculated based on the data received from the ECM.


w/o Multi-information Display:

The combination meter assembly controls the engine coolant temperature receiver gauge in accordance with engine coolant temperature signals from the engine coolant temperature sensor or water temperature sender gauge.


WIRING DIAGRAM

w/ Multi-information Display:


E402224E04
0.75,3.333 4.417,3.531 3.667,0.198 10 false : CAN Communication Line 1.688,2.49 2.135,2.688 0.448,0.198 10 false ECM 4.479,2.49 6.333,2.719 1.854,0.229 10 false Combination Meter Assembly


w/o Multi-information Display:


E199469E03
4.813,2.406 5.083,2.583 0.271,0.177 10 false J1 4.813,2.573 6.646,2.75 1.833,0.177 10 false Combination Meter Assembly 5.167,1.156 5.323,1.333 0.156,0.177 10 false S 3.292,1.063 3.448,1.24 0.156,0.177 10 false S 4.885,1.063 5.063,1.24 0.177,0.177 10 false 38 3.531,1.063 4.042,1.24 0.51,0.177 10 false 3*4 1.938,1.583 3.229,1.771 1.292,0.188 10 false A9*1, B32*2, B7*3 1.938,2.063 2.781,2.24 0.844,0.177 10 false k1*4 1.927,1.781 4.75,2 2.823,0.219 10 false Water Temperature Sender Gauge Assembly 1.938,2.24 4.406,2.427 2.469,0.188 10 false Engine Coolant Temperature Sensor 0.958,2.594 2.708,2.771 1.75,0.177 10 false *1: for 14B 0.958,2.875 3.823,3.052 2.865,0.177 10 false *2: for 1BZ-FPE 0.958,3.156 1.865,3.333 0.906,0.177 10 false *3: for 1HZ 0.958,3.438 3.594,3.656 2.635,0.219 10 false *4: for N04C-UH, N04C-VL, N04C-VQ 3.521,0.885 4.302,1.073 0.781,0.188 10 false 1*1, *2,*3


CAUTION / NOTICE / HINT

NOTICE:
·

The meter/gauge system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (w/ Multi-information Display) (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CHECK VEHICLE CONDITION
Result:
Result Proceed to
w/ Multi-information Display A
w/o Multi-information Display B



A

2.CHECK FOR DTC (ECD SYSTEM, SFI SYSTEM)

B

6.ENGINE MODEL
2.CHECK FOR DTC (ECD SYSTEM, SFI SYSTEM)
a.

Check for DTCs.


OK:

ECD system (for N04C) or SFI system (for 2TR-FE) DTC is not output.



Result:
Result proceed to
OK A
NG (for N04C) B
NG (for 2TR-FE) C



A

3.PERFORM ACTIVE TEST USING GTS (WATER TEMPERATURE METER OPERATION)

B

GO TO ECD SYSTEM

C

GO TO SFI SYSTEM

3.PERFORM ACTIVE TEST USING GTS (WATER TEMPERATURE METER OPERATION)
a.

Using the GTS, perform the Active Test (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter:
Tester Display Test Part Control Range Diagnostic Note
Water Temperature Meter Operation Engine coolant temperature receiver gauge LOW, NORMAL or HIGH Perform the test with the vehicle stopped and the engine idling.

HINT:

Confirm that the vehicle is stopped and the engine is idling.


OK:

Needle indication is normal according to the GTS operation.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (COOLANT TEMPERATURE)

NG

REPLACE COMBINATION METER ASSEMBLY

4.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Using the GTS, read the Data List (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Coolant Temperature Engine coolant temperature / Min.: 0°C (0°F), Max.: 127.5°C (261.5°F) 75 to 100°C (167 to 212°F): After warming up the engine -

OK:

Coolant temperature displayed on the GTS is between 75°C (167°F) and 100°C (212°F) after warming up.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (COOLANT TEMP, COOLANT TEMPERATURE)

NG

REPLACE COMBINATION METER ASSEMBLY

5.READ VALUE USING GTS (COOLANT TEMP, COOLANT TEMPERATURE)
a.

Using the GTS, read the Data List (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Coolant Temp Engine coolant temperature / Min.: 0°C (0°F), Max.: 127.5°C (261.5°F) 75 to 100°C (167 to 212°F): After warming up the engine -

Combination Meter:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Coolant Temperature Engine coolant temperature / Min.: 0°C (0°F), Max.: 127.5°C (261.5°F) 75 to 100°C (167 to 212°F): After warming up the engine -

OK:

"Coolant Temp" displayed on GTS is same as "Coolant Temperature" displayed on GTS.



Result:
Result proceed to
OK A
NG (for N04C) B
NG (for 2TR-FE) C



A

REPLACE COMBINATION METER ASSEMBLY

B

C

6.ENGINE MODEL
Result:
Result Proceed to
for N04C-UH, N04C-VL, NO4C-VQ A
except N04C-UH, N04C-VL, NO4C-VQ B



A

7.INSPECT COMBINATION METER ASSEMBLY (ENGINE COOLANT TEMPERATURE RECEIVER GAUGE)

B

9.INSPECT COMBINATION METER ASSEMBLY (ENGINE COOLANT TEMPERATURE RECEIVER GAUGE)
7.INSPECT COMBINATION METER ASSEMBLY (ENGINE COOLANT TEMPERATURE RECEIVER GAUGE)
a.
E204584E05
0.49,0.792 0.979,1.083 0.49,0.292 1.781,1.229 2.135,1.594 2.135,1.594 2.292,1.594 true 0.125,0.083 0.281,0.313 0.156,0.229 10 false *1 2.354,1.521 2.51,1.698 0.156,0.177 10 false S 0.656,0.854 0.969,1.094 0.313,0.24 10 false k1

Disconnect the engine coolant temperature sensor connector.


b.

Turn the ignition switch to ON, and then check the position of the receiver gauge needle.

OK:

Needle position is on COOL.



Text in Illustration
*1 Front view of wire harness connector
(to Engine Coolant Temperature Sensor)

c.

Connect terminal 3 (S) and body ground on the wire harness side connector of the engine coolant temperature sensor.


d.

Turn the ignition switch to ON, and then check the position of the receiver gauge needle.

OK:

Needle position is on HOT.



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ENGINE COOLANT TEMPERATURE SENSOR)

NG

REPLACE ENGINE COOLANT TEMPERATURE SENSOR

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ENGINE COOLANT TEMPERATURE SENSOR)
a.

Disconnect the J1 combination meter assembly connector.


b.

Disconnect the k1 engine coolant temperature sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-38 (S) - k1-3 (S) Always Below 1 Ω
J1-38 (S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT COMBINATION METER ASSEMBLY (ENGINE COOLANT TEMPERATURE RECEIVER GAUGE)
a.
E204585E02
0.688,1 1.115,1.292 0.427,0.292 0.688,0.604 1.115,0.896 0.427,0.292 0.698,1.427 1.125,1.719 0.427,0.292 1.792,1.042 2.073,1.385 2.073,1.385 2.271,1.385 true 0.094,0.073 0.25,0.25 0.156,0.177 10 false *1 2.375,1.302 2.531,1.479 0.156,0.177 10 false S 0.771,1.073 1.063,1.271 0.292,0.198 10 false B32 0.813,0.667 1.104,0.865 0.292,0.198 10 false A9 1.156,0.667 1.323,0.844 0.167,0.177 10 false *A 1.167,1.073 1.333,1.25 0.167,0.177 10 false *B 1.188,1.51 1.354,1.688 0.167,0.177 10 false *C 0.823,1.49 1.094,1.677 0.271,0.188 10 false B7

Disconnect the water temperature sender gauge connector.


b.

Turn the ignition switch to ON, and then check the position of the receiver gauge needle.

OK:

Needle position is on COOL.



Text in Illustration
*A for 14B
*B for 1BZ-FPE
*C for 1HZ
*1 Front view of wire harness connector
(to Water Temperature Sender Gauge)

c.

Connect terminal 1 (S) and body ground on the wire harness side connector of the water temperature sender gauge.


d.

Turn the ignition switch to ON, and then check the position of the receiver gauge needle.

OK:

Needle position is on HOT.



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS OR CONNECTOR (COMBINATION METER - WATER TEMPERATURE SENDER GAUGE)

NG

REPLACE WATER TEMPERATURE SENDER GAUGE ASSEMBLY

10.CHECK HARNESS OR CONNECTOR (COMBINATION METER - WATER TEMPERATURE SENDER GAUGE)

*1: for 14B

*2: for 1BZ-FPE

*3: for 1HZ


a.

Disconnect the J1 combination meter assembly connector.


b.

Disconnect the A9*1, B32*2 or B7*3 water temperature sender gauge connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-38 (S) - A9-1 (S)*1 Always Below 1 Ω
J1-38 (S) - B32-1 (S)*2 Always Below 1 Ω
J1-38 (S) - B7-1 (S)*3 Always Below 1 Ω
J1-38 (S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR