Home › Drivetrain › A861E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2019.08
RM2850E _52 Drivetrain _082622 A861E AUTOMATIC TRANSMISSION / TRANSAXLE _0398655 AUTOMATIC TRANSMISSION SYSTEM C

A861E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0710  Transmission Fluid Temperature Sensor "A" Circuit  


DESCRIPTION

The Automatic Transmission Fluid (ATF) temperature sensor converts the ATF temperature into a resistance value which is input into the transmission control ECU assembly.

The transmission control ECU assembly applies voltage to the temperature sensor through the transmission control ECU assembly terminal OIL2.

The sensor resistance changes with the transmission fluid temperature. As the temperature becomes higher, the sensor resistance decreases. One terminal of the sensor is grounded so that the sensor resistance decreases and the voltage goes down as the temperature becomes higher. The transmission control ECU assembly calculates the fluid temperature based on the voltage signal.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0710 Transmission Fluid Temperature Sensor "A" Circuit 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

-

2.

ATF temperature sensor resistance is below 59 Ω or higher than 309 kΩ

3.

0.5 seconds or more

4.

1 trip detection logic


·

Wire harness or connector (ATF temperature sensor circuit)

·

No. 1 transmission wire

·

Transmission valve body assembly (ATF temperature sensor)

·

Transmission control ECU assembly


- DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


1.

Turn the ignition switch to ON.


WIRING DIAGRAM

C452961E02
5.635,0.292 6.094,0.49 0.458,0.198 10 false OIL2 5.24,0.406 5.698,0.604 0.458,0.198 10 false B133 5.313,0.219 5.771,0.417 0.458,0.198 10 false 15 5.646,1.073 6.104,1.271 0.458,0.198 10 false E2 5.229,1.188 5.688,1.385 0.458,0.198 10 false B132 5.313,0.99 5.771,1.188 0.458,0.198 10 false 28 3.917,0.208 4.375,0.406 0.458,0.198 10 false 3 3.917,0.99 4.375,1.188 0.458,0.198 10 false 8 3.802,0.406 4.26,0.604 0.458,0.198 10 false B137 3.802,1.188 4.26,1.385 0.458,0.198 10 false B137 2.885,1.198 3.344,1.396 0.458,0.198 10 false A 2.885,0.427 3.344,0.625 0.458,0.198 10 false A 2.885,0.99 3.344,1.188 0.458,0.198 10 false 2 2.896,0.219 3.354,0.417 0.458,0.198 10 false 4 3.448,0.302 3.906,0.5 0.458,0.198 10 false OIL2 3.458,1.083 3.917,1.281 0.458,0.198 10 false GND 2.396,1.083 2.854,1.281 0.458,0.198 10 false GND 2.375,0.313 2.833,0.51 0.458,0.198 10 false OIL2 0.792,1.469 2.458,1.74 1.667,0.271 10 false ATF Temperature Sensor 0.802,2.021 3.042,2.594 2.24,0.573 10 false Transmission Valve Body Assembly (No. 1 Transmission Wire) 5.573,2 6.917,2.438 1.344,0.438 10 false Transmission Control ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

Perform initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION


PROCEDURE

1.INSPECT TRANSMISSION VALVE BODY ASSEMBLY (ATF TEMPERATURE SENSOR)
a.

Disconnect the No. 1 transmission wire connector.


b.
C233564C08
1.313,1.781 1.677,1.26 true 1.771,1.052 2.292,1.781 true 0.083,0.083 0.323,0.281 0.24,0.198 10 false *a 2.26,1.813 2.667,2 0.406,0.188 10 false OIL2 1.208,1.813 1.615,2 0.406,0.188 10 false GND
*a Component without harness connected
(No. 1 Transmission Wire)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (OIL2) - 8 (GND) Always 59 Ω to 309 kΩ
3 (OIL2) - Body ground Always 10 kΩ or higher
8 (GND) - Body ground Always 10 kΩ or higher


HINT:

If the resistance is out of the specified range at either of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.

ATF Temperature Specified Condition
10°C (50°F) 5.80 to 7.09 kΩ
110°C (230°F) 0.231 to 0.263 kΩ



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - TRANSMISSION CONTROL ECU ASSEMBLY)

NG

3.INSPECT NO. 1 TRANSMISSION WIRE
2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - TRANSMISSION CONTROL ECU ASSEMBLY)
a.

Disconnect the transmission control ECU assembly connector.


b.
C233567C03
0.958,0.063 1.375,0.313 0.417,0.25 1.656,0.052 2.063,0.323 0.406,0.271 0.792,2.031 1.063,1.74 true 1.75,1.635 2.438,1.563 true 1.01,0.115 1.385,0.323 0.375,0.208 10 false B132 1.708,0.115 2.104,0.302 0.396,0.188 10 false B133 0.125,0.104 0.427,0.281 0.302,0.177 10 false *a 0.281,1.958 0.865,2.156 0.583,0.198 10 false 28 (E2) 2.49,1.479 3.177,1.677 0.688,0.198 10 false 15 (OIL2)
*a Rear view of wire harness connector
(to Transmission Control ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B133-15 (OIL2) - B132-28 (E2) Always 59 Ω to 309 kΩ
B133-15 (OIL2) - Body ground Always 10 kΩ or higher
B132-28 (E2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NO. 1 TRANSMISSION WIRE

b.
C365247C02
2.771,1.74 3.177,1.958 0.406,0.219 1.396,1.292 1.76,0.729 true 1.844,0.896 2.156,1.302 true 2.677,2.969 2.896,2.521 true 2.354,2.604 2.875,2.281 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *1 2.938,1.792 3.25,1.99 0.313,0.198 10 false A 1.292,1.344 1.75,1.542 0.458,0.198 10 false OIL2 2.115,1.354 2.573,1.552 0.458,0.198 10 false GND 2.344,2.906 2.802,3.104 0.458,0.198 10 false OIL2 2.021,2.552 2.479,2.75 0.458,0.198 10 false GND
*1 No. 1 Transmission Wire


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (OIL2) - A-4 (OIL2) Always Below 1 Ω
8 (GND) - A-2 (GND) Always Below 1 Ω
3 (OIL2) or A-4 (OIL2) - Body ground Always 10 kΩ or higher
8 (GND) or A-2 (GND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG