Home › Drivetrain › A861E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › 2019.08–2021.01
RM2850E _52 Drivetrain _082622 A861E AUTOMATIC TRANSMISSION / TRANSAXLE _0398655 AUTOMATIC TRANSMISSION SYSTEM C

A861E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0725  Engine Speed Input Circuit  


DESCRIPTION

The ECM sends the engine speed signal to the transmission control ECU assembly. When there is a malfunction in the engine speed signal, the transmission control ECU assembly stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0725 Engine Speed Input Circuit 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

Vehicle is being driven (Shift lever not in P or N position)

2.

Engine speed (NE): Below 300 rpm

3.

4 seconds or more

4.

2 trip detection logic


·

Wire harness or connector (NE signal circuit)

·

ECM

·

Transmission control ECU assembly


O/D OFF Indicator Light: Blinking DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


1.

Perform the D Position Shift Test inspection in Road Test.*1

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>ROAD TEST

2.

Turn the ignition switch off.

3.

Perform step (*1) again.


WIRING DIAGRAM

C373976E01
1.083,2.115 1.542,2.313 0.458,0.198 10 false A115 1.094,2.281 3.094,2.458 2,0.177 10 false ECM 3.469,3.208 4.063,3.438 0.594,0.229 10 false to DLC3 4.698,1.302 5.083,1.469 0.385,0.167 10 false B134 5.26,2.563 6.604,3.01 1.344,0.448 10 false Transmission Control ECU Assembly 4.688,2 5.115,2.188 0.427,0.188 10 false B133 5.115,1.198 5.354,1.365 0.24,0.167 10 false NE 5.125,2.01 5.365,2.177 0.24,0.167 10 false E 1.646,1.177 1.969,1.344 0.323,0.167 10 false TAC 2.031,1.177 2.344,1.375 0.313,0.198 10 false 15 4.76,1.083 5.073,1.281 0.313,0.198 10 false 15 4.813,1.792 5.125,1.99 0.313,0.198 10 false 8

CAUTION / NOTICE / HINT

NOTICE:

Perform initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK DTC OUTPUT (ECD SYSTEM)
a.

Check whether crank angle sensor system DTCs have been output.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR


Result:
Result Proceed to
Crank angle sensor system DTCs have been output A
Crank angle sensor system DTC have not been output B


HINT:

If crank angle sensor system DTCs have been output, troubleshoot the ECD system first.



A

2.INSPECT TRANSMISSION CONTROL ECU ASSEMBLY (NE TERMINAL WAVEFORM)

B

2.INSPECT TRANSMISSION CONTROL ECU ASSEMBLY (NE TERMINAL WAVEFORM)
a.
C372884C01
1.719,0.354 2.115,0.604 0.396,0.25 2.198,0.354 2.594,0.604 0.396,0.25 1.885,1.708 2.125,1.188 true 2.656,1.708 2.417,1.281 true 0.125,0.094 0.427,0.292 0.302,0.198 10 false *a 1.771,0.417 2.167,0.594 0.396,0.177 10 false B133 2.24,0.417 2.635,0.615 0.396,0.198 10 false B134 1.76,1.771 2.188,1.938 0.427,0.167 10 false 8 (E) 2.573,1.75 3.135,1.948 0.563,0.198 10 false 15 (NE) 2.917,3.5 3.24,3.688 0.323,0.188 10 false GND
*a Component with harness connected
(Transmission Control ECU Assembly)


Connect an oscilloscope between the transmission control ECU assembly terminals specified in the table below.

Item Content
Terminal NE - E
Tool setting 2 V/DIV, 20 ms/DIV
Vehicle conditions Engine idling

HINT:

The wavelength shortens as the engine speed increases.



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (ECM - TRANSMISSION CONTROL ECU ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (ECM - TRANSMISSION CONTROL ECU ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the transmission control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A115-15 (TAC) - B134-15 (NE) Always Below 1 Ω
A115-15 (TAC) or B134-15 (NE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR