Home › Drivetrain › A861E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2019.08
RM2850E _52 Drivetrain _082622 A861E AUTOMATIC TRANSMISSION / TRANSAXLE _0398655 AUTOMATIC TRANSMISSION SYSTEM C

A861E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0730  Incorrect Gear Ratio  


DESCRIPTION

The transmission control ECU assembly detects the gear position based on signals from the speed sensor (NT) and transmission revolution sensor (NC). If the detected gear position differs from the commanded gear position, the transmission control ECU determines that there is a mechanical problem in the solenoid or inside the automatic transmission and stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0730 Incorrect Gear Ratio 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

Shift lever in D, 4 or 2/L

2.

The clutch slip (Turbine speed - output speed / gear ratio) is specified value or more

3.

0.5 seconds or more

4.

1 trip detection logic


·

Shift Solenoid Valve S1

·

Shift Solenoid Valve S2

·

Shift Solenoid Valve S3

·

Automatic transmission assembly


O/D OFF Indicator Light: Blinking DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



CAUTION / NOTICE / HINT

NOTICE:
·

When inspecting each shift solenoid valve, do not remove it from the transmission valve body assembly.

·

Perform initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION



HINT:
·

Refer to Parts Location for the location of each shift solenoid valve and each oil pressure switch.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>PARTS LOCATION

·

Use a new transmission wire if the pin and socket terminals are removed on each oil pressure switch.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Trouble Codes.


e.

Read DTCs using the GTS.


Result:
Result Proceed to
Only DTC P0730 is output A
DTC P0730 and other DTCs are output B


HINT:

If any other codes besides P0730 are output, perform troubleshooting for those DTCs first.



A

2.CLEAR DTC AND PERFORM ROAD TEST

B

2.CLEAR DTC AND PERFORM ROAD TEST
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Trouble Codes.


e.

Clear the DTCs.


f.

Perform the D Position Shift Test inspection in Road Test.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>ROAD TEST


Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Trouble Codes.


e.

Read DTCs using the GTS.


Result:
Result Proceed to
DTC is not output A
DTC P0730 is output B



A

B

4.INSPECT SHIFT SOLENOID VALVE S1
4.INSPECT SHIFT SOLENOID VALVE S1
a.
C357041C03
0.052,0.042 0.323,0.302 0.271,0.26 10 false *a
*a Component without harness connected
(Shift Solenoid Valve S1)


Disconnect the shift solenoid valve S1 connector.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT SOLENOID VALVE>REMOVAL

NOTICE:

When inspecting the shift solenoid valve S1, do not remove it from the transmission valve body assembly.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal of shift solenoid valve S1 connector - Shift solenoid valve S1 body 20°C (68°F) 11 to 15 Ω



c.

Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

5.INSPECT SHIFT SOLENOID VALVE S2

NG

5.INSPECT SHIFT SOLENOID VALVE S2
a.
C357041C03
0.052,0.042 0.323,0.302 0.271,0.26 10 false *a
*a Component without harness connected
(Shift Solenoid Valve S2)


Disconnect the shift solenoid valve S2 connector.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT SOLENOID VALVE>REMOVAL

NOTICE:

When inspecting the shift solenoid valve S2, do not remove it from the transmission valve body assembly.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal of shift solenoid valve S2 connector - Shift solenoid valve S2 body 20°C (68°F) 11 to 15 Ω



c.

Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

6.INSPECT SHIFT SOLENOID VALVE S3

NG

6.INSPECT SHIFT SOLENOID VALVE S3
a.
C357041C03
0.052,0.042 0.323,0.302 0.271,0.26 10 false *a
*a Component without harness connected
(Shift Solenoid Valve S3)


Disconnect the shift solenoid valve S3 connector.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT SOLENOID VALVE>REMOVAL

NOTICE:

When inspecting the shift solenoid valve S3, do not remove it from the transmission valve body assembly.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal of shift solenoid valve S3 connector - Shift solenoid valve S3 body 20°C (68°F) 11 to 15 Ω



c.

Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

NG