Home › Drivetrain › A861E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2019.08
RM2850E _52 Drivetrain _082622 A861E AUTOMATIC TRANSMISSION / TRANSAXLE _0398655 AUTOMATIC TRANSMISSION SYSTEM C

A861E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0973  Shift Solenoid "A" Control Circuit Low  P0974  Shift Solenoid "A" Control Circuit High  P0976  Shift Solenoid "B" Control Circuit Low  P0977  Shift Solenoid "B" Control Circuit High  P0979  Shift Solenoid "C" Control Circuit Low  P0980  Shift Solenoid "C" Control Circuit High  


DESCRIPTION

The transmission control ECU assembly controls gear shifting between 1st and 6th gears based on the combination of the SL1, SL2, SL3, S1, S2, and S3 solenoids. If there is an open or short in any of the solenoid valves, the transmission control ECU assembly turns the other solenoid valves on or off as part of fail-safe operation. Also, if all of the solenoid valves malfunction, only the mechanical hydraulic circuits will be available, and shifting will be manual only. (In the case of an open or short, the transmission control ECU assembly cuts the electrical power supply to the malfunctioning solenoid valve.)

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0973 Shift Solenoid "A" Control Circuit Low 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

-

2.

Shift solenoid valve S1 current 4 A or more

3.

0.1 seconds or more

4.

1 trip detection logic


·

Wire harness or connector (Shift solenoid valve S1 signal circuit)

·

No. 2 transmission wire

·

Shift solenoid valve S1

·

Transmission control ECU assembly


O/D OFF Indicator Light: Blinking DTC stored
P0974 Shift Solenoid "A" Control Circuit High 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

-

2.

Shift solenoid valve S1 resistance 100 kΩ or more

3.

0.1 seconds or more

4.

1 trip detection logic


·

Wire harness or connector (Shift solenoid valve S1 signal circuit)

·

No. 2 transmission wire

·

Shift solenoid valve S1

·

Transmission control ECU assembly


O/D OFF Indicator Light: Blinking DTC stored
P0976 Shift Solenoid "B" Control Circuit Low 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

-

2.

Shift solenoid valve S2 current 4 A or more

3.

0.1 seconds or more

4.

1 trip detection logic


·

Wire harness or connector (Shift solenoid valve S2 signal circuit)

·

No. 2 transmission wire

·

Shift solenoid valve S2

·

Transmission control ECU assembly


O/D OFF Indicator Light: Blinking DTC stored
P0977 Shift Solenoid "B" Control Circuit High 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

-

2.

Shift solenoid valve S2 resistance 100 kΩ or more

3.

0.1 seconds or more

4.

1 trip detection logic


·

Wire harness or connector (Shift solenoid valve S2 signal circuit)

·

No. 2 transmission wire

·

Shift solenoid valve S2

·

Transmission control ECU assembly


O/D OFF Indicator Light: Blinking DTC stored
P0979 Shift Solenoid "C" Control Circuit Low 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

-

2.

Shift solenoid valve S3 current 4 A or more

3.

0.1 seconds or more

4.

1 trip detection logic


·

Wire harness or connector (Shift solenoid valve S3 signal circuit)

·

No. 2 transmission wire

·

Shift solenoid valve S3

·

Transmission control ECU assembly


O/D OFF Indicator Light: Blinking DTC stored
P0980 Shift Solenoid "C" Control Circuit High 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

-

2.

Shift solenoid valve S3 resistance 100 kΩ or more

3.

0.1 seconds or more

4.

1 trip detection logic


·

Wire harness or connector (Shift solenoid valve S3 signal circuit)

·

No. 2 transmission wire

·

Shift solenoid valve S3

·

Transmission control ECU assembly


O/D OFF Indicator Light: Blinking DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



WIRING DIAGRAM

C372563E03
1.323,5.167 3.51,5.563 2.188,0.396 10 false No. 2 Transmission Wire 5.229,4.969 6.542,5.354 1.313,0.385 10 false Transmission Control ECU Assembly 1.396,4.073 2.906,4.375 1.51,0.302 10 false Shift Solenoid Valve S3 1.406,2.885 2.917,3.188 1.51,0.302 10 false Shift Solenoid Valve S2 1.417,1.677 2.927,1.979 1.51,0.302 10 false Shift Solenoid Valve S1 5.906,1.188 6.219,1.385 0.313,0.198 10 false IC 5.896,2.396 6.208,2.594 0.313,0.198 10 false IC 5.885,3.594 6.198,3.792 0.313,0.198 10 false IC 4.667,1.198 5.094,1.406 0.427,0.208 10 false B132 4.667,2.396 5.052,2.594 0.385,0.198 10 false B132 4.667,3.594 5.073,3.792 0.406,0.198 10 false B132 4.656,4.438 5.021,4.635 0.365,0.198 10 false B133 3.219,1.083 3.448,1.26 0.229,0.177 10 false S1 3.208,2.281 3.438,2.458 0.229,0.177 10 false S2 3.198,3.469 3.427,3.646 0.229,0.177 10 false S3 3.521,1.083 3.75,1.26 0.229,0.177 10 false 10 3.531,2.281 3.76,2.458 0.229,0.177 10 false 3 3.531,3.458 3.76,3.635 0.229,0.177 10 false 9 5.083,1.083 5.313,1.26 0.229,0.177 10 false S1 5.094,2.271 5.323,2.448 0.229,0.177 10 false S2 5.094,3.469 5.323,3.646 0.229,0.177 10 false S3 4.781,0.99 5.01,1.167 0.229,0.177 10 false 1 4.74,2.188 4.969,2.365 0.229,0.177 10 false 22 4.781,3.375 5.01,3.552 0.229,0.177 10 false 3 4.792,4.219 5.021,4.396 0.229,0.177 10 false 8 1.323,5.01 1.74,5.208 0.417,0.198 10 false B138 5.083,4.427 5.313,4.604 0.229,0.177 10 false E

CAUTION / NOTICE / HINT

NOTICE:
·

When inspecting each shift solenoid valve, do not remove it from the transmission valve body assembly.

·

Perform initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION



HINT:
·

Refer to Parts Location for the location of each shift solenoid valve and each oil pressure switch.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>PARTS LOCATION

·

Use a new transmission wire if the pin and socket terminals are removed on each oil pressure switch.



PROCEDURE

1.INSPECT NO. 2 TRANSMISSION WIRE (SHIFT SOLENOID VALVE S1, S2 AND S3)
a.

Disconnect the No. 2 transmission wire connector.


b.
C239950C07
1.813,1.271 1.948,1.74 true 1.073,1.729 1.521,1.281 true 1.906,1.073 2.521,1.75 true 0.198,0.135 0.469,0.323 0.271,0.188 10 false *a 0.938,1.771 1.177,1.927 0.24,0.156 10 false S1 1.865,1.781 2.104,1.938 0.24,0.156 10 false S3 2.531,1.792 2.771,1.948 0.24,0.156 10 false S2
*a Component without harness connected
(No. 2 Transmission Wire)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
10 (S1) - Body ground 20°C (68°F) 11 to 15 Ω
3 (S2) - Body ground 20°C (68°F) 11 to 15 Ω
9 (S3) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Result Proceed to
OK A
NG (Shift solenoid valve S1) B
NG (Shift solenoid valve S2) C
NG (Shift solenoid valve S3) D



A

2.CHECK HARNESS AND CONNECTOR (NO. 2 TRANSMISSION WIRE - TRANSMISSION CONTROL ECU ASSEMBLY)

B

3.INSPECT SHIFT SOLENOID VALVE S1

C

4.INSPECT SHIFT SOLENOID VALVE S2

D

5.INSPECT SHIFT SOLENOID VALVE S3
2.CHECK HARNESS AND CONNECTOR (NO. 2 TRANSMISSION WIRE - TRANSMISSION CONTROL ECU ASSEMBLY)
a.

Disconnect the transmission control ECU assembly connector.


b.
C233560C13
1,0.073 1.427,0.313 0.427,0.24 1.677,0.073 2.115,0.313 0.438,0.24 1.302,1.563 0.583,1.302 true 2.438,1.438 2.104,0.844 true 1.51,1.573 1.781,1.479 true 1.51,1.76 1.75,1.938 true 0.073,0.063 0.25,0.229 0.177,0.167 10 false *a 1.063,0.115 1.438,0.271 0.375,0.156 10 false B132 0.146,1.219 0.698,1.417 0.552,0.198 10 false 3 (S3) 2.385,1.469 2.844,1.635 0.458,0.167 10 false 8 (E) 1.823,1.396 2.292,1.583 0.469,0.188 10 false 1 (S1) 1.802,1.885 2.323,2.094 0.521,0.208 10 false 22 (S2) 1.74,0.125 2.125,0.292 0.385,0.167 10 false B133
*a Rear view of wire harness connector
(to Transmission Control ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B132-1 (S1) - B133-8 (E) 20°C (68°F) 11 to 15 Ω
B132-22 (S2) - B133-8 (E) 20°C (68°F) 11 to 15 Ω
B133-3 (S3) - B133-8 (E) 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE S1
a.
C365573C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Shift Solenoid Valve S1)


Disconnect the shift solenoid valve S1 connector.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT SOLENOID VALVE>REMOVAL

NOTICE:

When inspecting the shift solenoid valve S1, do not remove it from the transmission valve body assembly.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal of shift solenoid valve S1 connector - Shift solenoid valve S1 body 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT SHIFT SOLENOID VALVE S2
a.
C365573C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Shift Solenoid Valve S2)


Disconnect the shift solenoid valve S2 connector.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT SOLENOID VALVE>REMOVAL

NOTICE:

When inspecting the shift solenoid valve S2, do not remove it from the transmission valve body assembly.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal of shift solenoid valve S2 connector - Shift solenoid valve S2 body 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

NG

5.INSPECT SHIFT SOLENOID VALVE S3
a.
C365573C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Shift Solenoid Valve S3)


Disconnect the shift solenoid valve S3 connector.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT SOLENOID VALVE>REMOVAL

NOTICE:

When inspecting the shift solenoid valve S3, do not remove it from the transmission valve body assembly.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal of shift solenoid valve S3 connector - Shift solenoid valve S3 body 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

NG