Home › Drivetrain › A861E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2019.08
RM2850E _52 Drivetrain _082622 A861E AUTOMATIC TRANSMISSION / TRANSAXLE _0398655 AUTOMATIC TRANSMISSION SYSTEM C

A861E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0985  Shift Solenoid "E" Control Circuit Low  P0986  Shift Solenoid "E" Control Circuit High  


DESCRIPTION

Based on the signal from the transmission control ECU assembly, the shift solenoid valve S4 controls the pressure switching valve and converts the output pressure of the No. 1 control valve and No. 2 control valve to line pressure. This line pressure is used to operate the clutch and brake. If there is an open or short in the S4 solenoid system, the transmission control ECU assembly stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0985 Shift Solenoid "E" Control Circuit Low 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

-

2.

Shift solenoid valve S4 current 4 A or more

3.

0.1 seconds or more

4.

1 trip detection logic


·

Wire harness or connector (Shift solenoid valve S4 signal circuit)

·

No. 2 transmission wire

·

Shift solenoid valve S4

·

Transmission control ECU assembly


O/D OFF Indicator Light: Blinking DTC stored
P0986 Shift Solenoid "E" Control Circuit High 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

-

2.

Shift solenoid valve S4 resistance 100 kΩ or more

3.

0.1 seconds or more

4.

1 trip detection logic


·

Wire harness or connector (Shift solenoid valve S4 signal circuit)

·

No. 2 transmission wire

·

Shift solenoid valve S4

·

Transmission control ECU assembly


O/D OFF Indicator Light: Blinking DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



WIRING DIAGRAM

C372564E03
0.938,2.677 1.396,2.875 0.458,0.198 10 false B138 0.927,2.833 3.104,3.229 2.177,0.396 10 false No. 2 Transmission Wire 5.156,2.927 5.615,3.125 0.458,0.198 10 false B133 5.156,3.083 6.479,3.542 1.323,0.458 10 false Transmission Control ECU Assembly 1.354,1.74 2.979,2.094 1.625,0.354 10 false Shift Solenoid Valve S4 3.156,1.146 3.396,1.313 0.24,0.167 10 false S4 5.042,1.125 5.281,1.292 0.24,0.167 10 false S4 5.854,1.25 6.094,1.417 0.24,0.167 10 false IC 5.042,2.396 5.281,2.563 0.24,0.167 10 false E 3.479,1.146 3.719,1.313 0.24,0.167 10 false 4 4.76,1.125 4.979,1.292 0.219,0.167 10 false 19 4.823,2.281 4.948,2.458 0.125,0.177 10 false 8

CAUTION / NOTICE / HINT

NOTICE:
·

When inspecting each shift solenoid valve, do not remove it from the transmission valve body assembly.

·

Perform initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION



HINT:
·

Refer to Parts Location for the location of each shift solenoid valve and each oil pressure switch.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>PARTS LOCATION

·

Use a new transmission wire if the pin and socket terminals are removed on each oil pressure switch.



PROCEDURE

1.INSPECT NO. 2 TRANSMISSION WIRE (SHIFT SOLENOID VALVE S4)
a.

Disconnect the No. 2 transmission wire connectors.


b.
C239950C08
1.073,1.729 1.542,1.083 true 0.198,0.135 0.469,0.323 0.271,0.188 10 false *a 0.938,1.771 1.177,1.927 0.24,0.156 10 false S4
*a Component without harness connected
(No. 2 Transmission Wire)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (S4) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NO. 2 TRANSMISSION WIRE - TRANSMISSION CONTROL ECU ASSEMBLY)

NG

3.INSPECT SHIFT SOLENOID VALVE S4
2.CHECK HARNESS AND CONNECTOR (NO. 2 TRANSMISSION WIRE - TRANSMISSION CONTROL ECU ASSEMBLY)
a.

Disconnect the transmission control ECU assembly connector.


b.
C233561C06
1.698,0.073 2.125,0.333 0.427,0.26 2.135,1.635 2.448,1.427 true 2.5,1.927 2,1.729 true 1.76,0.135 2.135,0.313 0.375,0.177 10 false B133 0.135,0.104 0.427,0.271 0.292,0.167 10 false *a 2.573,1.865 3.063,2.031 0.49,0.167 10 false 19 (S4) 2.521,1.333 2.927,1.5 0.406,0.167 10 false 8 (E)
*a Rear view of wire harness connector
(to Transmission Control ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B133-19 (S4) - B133-8 (E) 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE S4
a.
C365573C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Shift Solenoid Valve S4)


Disconnect the shift solenoid valve S4 connector.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT SOLENOID VALVE>REMOVAL

NOTICE:

When inspecting the shift solenoid valve S4, do not remove it from the transmission valve body assembly.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal of shift solenoid valve S4 connector - Shift solenoid valve S4 body 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

NG