Home › Drivetrain › A861E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › 2019.08–2021.01
RM2850E _52 Drivetrain _082622 A861E AUTOMATIC TRANSMISSION / TRANSAXLE _0398655 AUTOMATIC TRANSMISSION SYSTEM C

A861E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P1604  Engine Control System Malfunction  


DESCRIPTION

·

The accelerator position sensor, which is installed to the accelerator pedal, detects the accelerator pedal position. When the ECM detects a malfunction in the accelerator position sensor, it sends a malfunction detection signal to the transmission control ECU assembly. A DTC is output when the transmission control ECU assembly receives this signal.

·

A DTC is output when a malfunction signal is received from the ECM for the engine torque amount requested from the transmission control ECU assembly, or when the signal cannot be received.

·

During sudden braking or when performing shift control while driving under lock-up, CAN communication is used to send an exhaust brake cut request signal to the ECM. A DTC is output when an exhaust brake operating signal is received while this exhaust brake cut request signal is sent.


DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P1604 Engine Control System Malfunction 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
DTC Detection Condition 1:
1.

CAN communication is normal

2.

Accelerator position or engine torque ratio malfunction signal received from ECM, or no signal

3.

0.5 seconds or more

4.

1 trip detection logic


DTC Detection Condition 2:
1.

CAN communication is normal

2.

Exhaust brake operating signal received during shift operation

3.

0.5 seconds or more

4.

8 trip detection logic


·

ECD system

·

CAN communication system

·

ECM

·

Transmission control ECU assembly


O/D OFF Indicator Light: Blinking DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


1.

Start the engine.*1

2.

Turn the exhaust brake switch to ON.*2

3.

Perform the D Position Shift Test inspection in Road Test.*3

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>ROAD TEST

4.

Turn the ignition switch off.*4

5.

Perform steps (*1) through (*4) 8 times.


CAUTION / NOTICE / HINT

NOTICE:

Perform initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK DTC OUTPUT (ECD SYSTEM)

Result:
Result Proceed to
ECD system DTCs are not output A
ECD system DTCs are output B


HINT:

If any other codes besides ECD system DTCs are output, perform troubleshooting for those DTCs first.



A

2.CHECK DTC OUTPUT

B

2.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Trouble Codes.


e.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTC U0100 is not output A
DTC U0100 is output B


HINT:

If any DTCs other than P1604 are output, perform troubleshooting for those DTCs first.



A

3.CHECK CAN COMMUNICATION SYSTEM

B

3.CHECK CAN COMMUNICATION SYSTEM

Result:
Result Proceed to
CAN communication system is normally A
CAN communication system is abnormal B



A

4.REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

B

4.REPLACE TRANSMISSION CONTROL ECU ASSEMBLY
a.

Replace the transmission control ECU assembly.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Trouble Codes.


e.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTCs are not output A
DTC P1604 is output B



A

END

B