Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0006  Fuel Shutoff Valve "A" Control Circuit Low  P0007  Fuel Shutoff Valve "A" Control Circuit High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0006 Fuel Shutoff Valve "A" Control Circuit Low Diagnosis Condition:
·

Fuel addition cut valve assembly activity request is in progress.

·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V


Malfunction Status:

The condition that the fuel addition cut valve assembly circuit voltage is 2.8 V or less remains for 15 seconds.


Malfunction Duration:

15 seconds or more


·

Harness or connector

·

Fuel addition cut valve assembly

·

ECM


Class C DTC stored
P0007 Fuel Shutoff Valve "A" Control Circuit High Diagnosis Condition:
·

Fuel addition cut valve assembly is not in operation.

·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V


Malfunction Status:
·

The condition that the fuel addition cut valve assembly circuit voltage is 3 V or more remains for 3 seconds.


Malfunction Duration:

3 seconds or more


·

Harness or connector

·

Fuel addition cut valve assembly

·

ECM


Class C DTC stored

MONITOR DESCRIPTION

The fuel addition fuel pipe is closed by the fuel addition cut valve assembly when the failure in the fuel addition cut valve assembly is occurred.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0006 Ignition switch ON for 15 seconds or more
P0007 Ignition switch ON for 3 seconds or more

WIRING DIAGRAM

A407157E04
2.177,1.906 5.542,2.104 3.365,0.198 10 false Fuel Addition Cut Valve Assembly 2.198,1.74 2.823,1.958 0.625,0.219 10 false B144 2.052,1.167 2.365,1.365 0.313,0.198 10 false 2 3.229,1.167 3.542,1.365 0.313,0.198 10 false 1 5.25,1.323 5.604,1.521 0.354,0.198 10 false FCV 4.844,1.302 5.198,1.5 0.354,0.198 10 false B142 4.917,1.094 5.271,1.292 0.354,0.198 10 false 96 4.49,1.302 4.844,1.5 0.354,0.198 10 false E-31 5.677,2.417 6.323,2.677 0.646,0.26 10 false ECM 2.917,1.198 3.229,1.396 0.313,0.198 10 false +B 2.208,1.198 2.521,1.396 0.313,0.198 10 false GND

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P0006 is output A
DTC P0007 is output B




A

2.INSPECT FUEL ADDITION CUT VALVE ASSEMBLY

B

9.CHECK CONNECTOR CONNECTION CONDITION
2.INSPECT FUEL ADDITION CUT VALVE ASSEMBLY
a.

Inspect the fuel addition cut valve assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL ADDITION CUT VALVE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

NG

8.REPLACE FUEL ADDITION CUT VALVE ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-31 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK DTC OUTPUT

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P0006 is output A
DTCs are not output B




A

5.REPLACE ECM

B

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
8.REPLACE FUEL ADDITION CUT VALVE ASSEMBLY
a.

Replace the fuel addition cut valve assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL ADDITION CUT VALVE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
9.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connector connection for the fuel addition injector cut valve assembly connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

10.INSPECT FUEL ADDITION CUT VALVE ASSEMBLY

NG

16.CONNECT SECURELY
10.INSPECT FUEL ADDITION CUT VALVE ASSEMBLY
a.

Inspect the fuel addition cut valve assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL ADDITION CUT VALVE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

NG

8.REPLACE FUEL ADDITION CUT VALVE ASSEMBLY
11.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-31 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN WIRE HARNESS)

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
12.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN WIRE HARNESS)
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A409073C07
0.396,1.063 0.823,1.354 0.427,0.292 1.198,1.844 1.5,1.354 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.458,1.135 1.021,1.51 0.563,0.375 10 false B144 1.094,1.885 1.552,2.115 0.458,0.229 10 false +B
*a Front view of wire harness connector
(to Fuel Addition Cut Valve Assembly)


Disconnect the ECM connector.


b.

Disconnect the fuel addition cut valve assembly connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-31 - B144-1 (+B) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (CHECK FOR GROUND)

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
13.CHECK HARNESS AND CONNECTOR (CHECK FOR GROUND)
A409073C06
0.396,1.063 0.823,1.354 0.427,0.292 2.208,1.844 1.906,1.344 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.458,1.135 1.021,1.51 0.563,0.375 10 false B144 2.125,1.896 2.688,2.146 0.563,0.25 10 false GND
*a Front view of wire harness connector
(to Fuel Addition Cut Valve Assembly)


a.

Disconnect the fuel addition cut valve assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B144-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

14.CHECK DTC OUTPUT

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
14.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P0007 is output A
DTCs are not output B




A

5.REPLACE ECM

B

END

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
16.CONNECT SECURELY
a.

Connect securely the fuel addition cut valve assembly connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT