Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0111  Intake Air Temperature Sensor 1 Circuit Range/Performance Bank 1  P0112  Intake Air Temperature Sensor 1 Circuit Low Bank 1  P0113  Intake Air Temperature Sensor 1 Circuit High Bank 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0111 Intake Air Temperature Sensor 1 Circuit Range/Performance Bank 1 Diagnosis Condition:
·

The following conditions continue for at least 20 seconds:

-

Engine speed is range of 570 to 1000 rpm.

-

Fuel injection rate is at least 4 to 35 mm3/st. or less.

-

Engine coolant temperature is between -30°C (-22°F) to 55°C (131°F).

-

Battery voltage is in the range of 10 V to 16 V



Malfunction Status:
·

The following conditions continue for at least 3 seconds:

-

Difference between intake air temperature (mass air flow meter) and intercooler outlet temperature is at least 30°C (86°F), and difference between intake air temperature (mass air flow meter) and intake manifold air temperature is at least 30°C (86°F).



Malfunction Duration:

3 seconds or more


·

Intake air temperature sensor (built into mass air flow meter)

·

ECM


Class B1 DTC stored
P0112 Intake Air Temperature Sensor 1 Circuit Low Bank 1 Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

Output of the intake air temperature sensor (built into mass air flow meter) remains less than 0.06 V (90°C (194°F)) for 60 seconds or longer.


Malfunction Duration:

60 seconds or more


·

Intake air temperature sensor (built into mass air flow meter)

·

Harness or connector

·

ECM


Class B1 DTC stored
P0113 Intake Air Temperature Sensor 1 Circuit High Bank 1 Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

Output of the intake air temperature sensor (built into mass air flow meter) remains at 4.55 V (-42°C (-43.6°F)) or more for 3 seconds or longer.


Malfunction Duration:

3 seconds or more


·

Intake air temperature sensor (built into mass air flow meter)

·

Harness or connector

·

ECM


Class B1 DTC stored

MONITOR DESCRIPTION

The intake air temperature sensor (built into mass air flow meter) constantly measures the intake air temperature.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0111 Start the engine for 60 seconds or more.
P0112
P0113
Ignition switch ON for 60 seconds or more.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER))
a.

Check the connector connection for the intake air temperature sensor (built into mass air flow meter) connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER)

NG

14.CONNECT SECURELY
2.CHECK INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER)
a.

Check the installation of the intake air temperature sensor (built into mass air flow meter).


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the sensor.


Result:
Proceed to
OK
NG



OK

3.INSPECT INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER)

NG

13.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER)
3.INSPECT INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER)
a.

Inspect the intake air temperature sensor (built into mass air flow meter).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER)

NG

12.REPLACE INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER)
4.CHECK INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER)
A451192C05
0.385,0.948 0.802,1.24 0.417,0.292 1.01,1.813 1.427,1.135 true 2.021,1.854 1.583,1.135 true 0.49,1.031 0.948,1.229 0.458,0.198 10 false B51 0.896,1.854 1.354,2.052 0.458,0.198 10 false THA 1.979,1.896 2.438,2.094 0.458,0.198 10 false E2 0.094,0.104 0.552,0.302 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Intake Air Temperature Sensor (Built Into Mass Air Flow Meter))


a.

Disconnect the intake air temperature sensor (built into mass air flow meter) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B51-1 (THA) - B51-2 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

5.CHECK DTC OUTPUT

NG

8.CHECK HARNESS OR CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P0111, P0112 or P0113 is output A
DTCs are not output B




A

6.REPLACE ECM

B

END

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

8.CHECK HARNESS OR CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Disconnect the intake air temperature sensor (built into mass air flow meter) connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C19
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405886C06
1.5,0.083 1.917,0.354 0.417,0.271 1.646,0.146 1.802,0.344 0.156,0.198 10 false M 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-47 - Body ground and other terminals Always 10 kΩ or higher
M-32 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS OR CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.CHECK HARNESS OR CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405886C06
1.5,0.083 1.917,0.354 0.417,0.271 1.646,0.146 1.802,0.344 0.156,0.198 10 false M 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a
*a Signal Check Harness Lead Connector


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-47 - M-32 -20°C 13.6 to 18.4 kΩ
20°C 2.21 to 2.69 kΩ
60°C 0.49 to 0.67 kΩ



Result:
Proceed to
OK
NG



OK

5.CHECK DTC OUTPUT

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
12.REPLACE INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER)
a.

Replace the intake air temperature sensor (built into mass air flow meter).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
13.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER)
a.

intake air temperature sensor (built into mass air flow meter) carry out air blow from the suction port of the main body and install it properly.

HINT:

If damaged, replace the mass air flow meter.



Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
14.CONNECT SECURELY
a.

Connect securely the intake air flow meter sub-assembly connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT