Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0263  Cylinder 1 Contribution/Balance  P0266  Cylinder 2 Contribution/Balance  P0269  Cylinder 3 Contribution/Balance  P0272  Cylinder 4 Contribution/Balance  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0263 Cylinder 1 Contribution/Balance Diagnosis Condition:
·

The following conditions continue for more than 30 seconds.

-

The engine speed is in the range of lower than 850 rpm.

-

The fuel injection quantity is within 0 to 40 mm3/st.

-

The vehicle speed is lower than 5 km/h (3 mile).



Malfunction Status:

The state that the amount of injection exceeds the threshold (29 mm3/st) continues for at least 30 seconds.


Malfunction Duration:

30 seconds or more


·

Fuel injection pipe (breakage, crack, fuel leakage)

·

Injector assembly

·

Fuel filter element sub-assembly

·

Engine assembly (compression leakage, Faulty valve clearance adjustment)

·

ECM


- DTC stored
P0266 Cylinder 2 Contribution/Balance Diagnosis Condition:
·

The following conditions continue for more than 30 seconds.

-

The engine speed is in the range of lower than 850 rpm.

-

The fuel injection quantity is within 0 to 40 mm3/st.

-

The vehicle speed is lower than 5 km/h (3 mile).



Malfunction Status:

The state that the amount of injection exceeds the threshold (29 mm3/st) continues for at least 30 seconds.


Malfunction Duration:

30 seconds or more


·

Fuel injection pipe (breakage, crack, fuel leakage)

·

Injector assembly

·

Fuel filter element sub-assembly

·

Engine assembly (compression leakage, Faulty valve clearance adjustment)

·

ECM


- DTC stored
P0269 Cylinder 3 Contribution/Balance Diagnosis Condition:
·

The following conditions continue for more than 30 seconds.

-

The engine speed is in the range of lower than 850 rpm.

-

The fuel injection quantity is within 0 to 40 mm3/st.

-

The vehicle speed is lower than 5 km/h (3 mile).



Malfunction Status:

The state that the amount of injection exceeds the threshold (29 mm3/st) continues for at least 30 seconds.


Malfunction Duration:

30 seconds or more


·

Fuel injection pipe (breakage, crack, fuel leakage)

·

Injector assembly

·

Fuel filter element sub-assembly

·

Engine assembly (compression leakage, Faulty valve clearance adjustment)

·

ECM


- DTC stored
P0272 Cylinder 4 Contribution/Balance Diagnosis Condition:
·

The following conditions continue for more than 30 seconds.

-

The engine speed is in the range of lower than 850 rpm.

-

The fuel injection quantity is within 0 to 40 mm3/st.

-

The vehicle speed is lower than 5 km/h (3 mile).



Malfunction Status:

The state that the amount of injection exceeds the threshold (29 mm3/st) continues for at least 30 seconds.


Malfunction Duration:

30 seconds or more


·

Fuel injection pipe (breakage, crack, fuel leakage)

·

Injector assembly

·

Fuel filter element sub-assembly

·

Engine assembly (compression leakage, Faulty valve clearance adjustment)

·

ECM


- DTC stored

MONITOR DESCRIPTION

P0263:

·

The rotation speed of No. 1 cylinder is monitored by the crankshaft position sensor (NE sensor).

·

The amount of injection compensation for No. 1 cylinder is increased or decreased to make the rotation speed of each cylinder constant.


P0266:

·

The rotation speed of No. 2 cylinder is monitored by the crankshaft position sensor (NE sensor).

·

The amount of injection compensation for No. 2 cylinder is increased or decreased to make the rotation speed of each cylinder constant.


P0269:

·

The rotation speed of No. 3 cylinder is monitored by the crankshaft position sensor (NE sensor).

·

The amount of injection compensation for No. 3 cylinder is increased or decreased to make the rotation speed of each cylinder constant.


P0272:

·

The rotation speed of No. 4 cylinder is monitored by the crankshaft position sensor (NE sensor).

·

The amount of injection compensation for No. 4 cylinder is increased or decreased to make the rotation speed of each cylinder constant.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0263
P0266
P0269
P0272
After warming up engine, idle engine for 60 seconds or more.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When P0263, P0266, P0269, or P0272 is output and the GTS is used to clear the DTC, the same DTC will be output again. Therefore, clear it by disconnecting the battery.

·

After replacing the injector assembly, the ECM needs registration (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).

·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:
·

When P0263 is displayed, check the No. 1 injector assembly circuit.

·

When P0266 is displayed, check the No. 2 injector assembly circuit.

·

When P0269 is displayed, check the No. 3 injector assembly circuit.

·

When P0272 is displayed, check the No. 4 injector assembly circuit.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P0263, P0266, P0269 or P0272 is output A
DTC P0263, P0266, P0269 or P0272 and other DTC are output B




A

2.CHECK FUEL HOSE

B

2.CHECK FUEL HOSE
a.

Check that the fuel cap, hose, and piping do not have fuel leak or clogging.

Major parts to check
·

Contamination of the fuel tank by foreign material.

·

Breakage, collapse, and looseness of the fuel hose.

·

Breakage, collapse, and looseness of the high pressure pipe.



Result:
Proceed to
OK
NG



OK

3.CHECK FUEL FILTER ELEMENT SUB-ASSEMBLY

NG

20.REPLACE FUEL PIPES AND HOSES
3.CHECK FUEL FILTER ELEMENT SUB-ASSEMBLY
a.

Check that the fuel filter element sub-assembly does not have dirt, clogging, or damage.


Result:
Proceed to
OK
NG



OK

4.CHECK FUEL FILTER ELEMENT SET

NG

18.REPLACE FUEL FILTER ELEMENT SUB-ASSEMBLY
4.CHECK FUEL FILTER ELEMENT SET
a.

Check the fuel filter element set.

·

Has the replacement period expired.

·

Is it a genuine Hino part?



b.

Check for bleeding the air from the fuel filter element set at adequate levels.


c.

Check the fuel filter element set connections for breathing the air and fuel leakage.

HINT:

If the air bleeding plug is loosened, it is caused by breathing the air into the fuel system.



Result:
Proceed to
OK
NG



OK

5.CHECK DTC OUTPUT

NG

17.REPLACE FUEL FILTER ELEMENT SET
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P0263, P0266, P0269 or P0272 is output A
DTCs are not output B




A

6.REPLACE INJECTOR ASSEMBLY

B

END

6.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P0263, P0266, P0269 or P0272 is output A
DTCs are not output B




A

8.REPLACE COMMON RAIL ASSEMBLY

B

END

8.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>COMMON RAIL>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT
9.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P0263, P0266, P0269 or P0272 is output A
DTCs are not output B




A

10.CHECK NOZZLE HOLDER CLAMP

B

END

10.CHECK NOZZLE HOLDER CLAMP
a.

Check that the injector nozzle clamp is not loose.


b.

Check that the claws of the injector nozzle clamp is not in the state of "Defective hooking".


Result:
Proceed to
OK
NG



OK

11.INSPECT VALVE CLEARANCE

NG

23.REPAIR OR REPLACE NOZZLE HOLDER CLAMP
11.INSPECT VALVE CLEARANCE
a.

Inspect that the valve clearance of each cylinder is within the standard range. (Check all valves.)


Result:
Proceed to
OK
NG



OK

12.INSPECT COMPRESSION PRESSURE

NG

22.ADJUST VALVE CLEARANCE
12.INSPECT COMPRESSION PRESSURE
a.

Inspect the compression pressure.


Result:
Proceed to
OK
NG



OK

13.CHECK CRANKSHAFT POSITION SENSOR

NG

21.ENGINE OVERHAUL
13.CHECK CRANKSHAFT POSITION SENSOR
a.

Check the installation of the crankshaft position sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the crankshaft position sensor.


Result:
Proceed to
OK
NG



OK

14.CHECK DTC OUTPUT

NG

19.REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR
14.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P0263, P0266, P0269 or P0272 is output A
DTCs are not output B




A

15.CHECK ENGINE

B

END

15.CHECK ENGINE
a.

Check the drive system parts such as crankshaft, connecting rod, and flywheel.


Result:
Proceed to
OK
NG



OK

END

NG

16.ENGINE OVERHAUL
16.ENGINE OVERHAUL
a.

Overhaul the engine.


Result:
Proceed to
NEXT



NEXT

24.CHECK DTC OUTPUT
17.REPLACE FUEL FILTER ELEMENT SET
a.

Replace the fuel filter element set.


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
18.REPLACE FUEL FILTER ELEMENT SUB-ASSEMBLY
a.

Replace the fuel filter element sub-assembly.


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
19.REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR
a.

Repair or replace the crankshaft position sensor.


Result:
Proceed to
NEXT



NEXT

24.CHECK DTC OUTPUT
20.REPLACE FUEL PIPES AND HOSES
a.

Replace the fuel pipes and hoses.


Result:
Proceed to
NEXT



NEXT

3.CHECK FUEL FILTER ELEMENT SUB-ASSEMBLY
21.ENGINE OVERHAUL
a.

Overhaul the engine.


Result:
Proceed to
NEXT



NEXT

24.CHECK DTC OUTPUT
22.ADJUST VALVE CLEARANCE
a.

Adjust the valve clearance.


Result:
Proceed to
NEXT



NEXT

24.CHECK DTC OUTPUT
23.REPAIR OR REPLACE NOZZLE HOLDER CLAMP
a.

Repair or replace the nozzle holder clamp.


Result:
Proceed to
NEXT



NEXT

24.CHECK DTC OUTPUT
24.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END