Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0506  Idle Control System RPM - Lower Than Expected  P0507  Idle Control System RPM - Higher Than Expected  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0506 Idle Control System RPM - Lower Than Expected Diagnosis Condition:

Ignition switch ON


·

The conditions described below remain for 10 seconds or longer.

-

Accelerator pedal opening = 0% (pedal not depressed)

-

Engine coolant temperature is 60°C (140°F) or higher.

-

The target idling speed is within the range of 595 to 605 rpm.

-

Vehicle speed is 0 km/h (0 mile).

-

The monitor disable DTC table can be referred to.



Malfunction Status:

Actual speed remains at 575 rpm or lower for 15 seconds or longer.


Malfunction Duration:

15 seconds or more


·

Injector assembly

·

Transmission

·

Compressor and magnetic clutch

·

Vane pump assembly


Class B1 DTC stored
P0507 Idle Control System RPM - Higher Than Expected Diagnosis Condition:

Ignition switch ON


·

The conditions described below remain for 10 seconds or longer.

-

Accelerator pedal opening = 0% (pedal not depressed)

-

Engine coolant temperature is 60°C (140°F) or higher.

-

The target idling speed is within the range of 595 to 605 rpm.

-

Vehicle speed is 0 km/h (0 mile).

-

The monitor disable DTC table can be referred to.



Malfunction Status:

Actual speed remains at 625 rpm or higher for 15 seconds or longer.


Malfunction Duration:

15 seconds or more


·

Injector assembly

·

Transmission

·

Compressor and magnetic clutch

·

Vane pump assembly


Class B1 DTC stored

MONITOR DESCRIPTION

A difference between a target speed and an actual speed is detected during idling in the ECM.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0506
P0507
After warming up engine, idle engine for 15 seconds or more.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read Current DTCs.

Result:
Result Proceed to
DTC P0506 or P0507 is output A
DTCs are not output B




A

2.READ VALUE USING GTS (INJECTION VOLUME AND ENGINE SPEED)

B

2.READ VALUE USING GTS (INJECTION VOLUME AND ENGINE SPEED)
a.

Start the engine.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed, Injection Volume


d.

Read the value.


Standard:
Item Condition Reference Value
Engine Speed
·

Engine speed: 1500 rpm

·

Engine coolant temperature: 80°C or higher

·

Shift position N

·

A/C OFF

·

Air compressor OFF


Speed fluctuation amount is 15 rpm or less
Injection Volume 5 mm3/st or more


Result:
Proceed to
OK
NG



OK

3.CHECK COMPRESSOR AND MAGNETIC CLUCH

NG

10.REPLACE INJECTOR ASSEMBLY
3.CHECK COMPRESSOR AND MAGNETIC CLUCH
a.

Check the compressor and magnetic clutch.

Click hereVehicle Interior>AIR CONDITIONING>COMPRESSOR (for N04C-WA)>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK VANE PUMP ASSEMBLY

NG

9.REPLACE COMPRESSOR AND MAGNETIC CLUCH
4.CHECK VANE PUMP ASSEMBLY

Result:
Proceed to
OK
NG



OK

5.CHECK DTC OUTPUT

NG

8.REPLACE VANE PUMP ASSEMBLY
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P0506 or P0507 is output A
DTCs are not output B




A

6.REPLACE ECM

B

END

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

8.REPLACE VANE PUMP ASSEMBLY

Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
9.REPLACE COMPRESSOR AND MAGNETIC CLUCH
a.

Replace the compressor and magnetic clutch.

Click hereVehicle Interior>AIR CONDITIONING>COMPRESSOR (for N04C-WA)>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
10.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT