Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P119F  Fuel Rail Pressure Sensor "A" Circuit Out of Range  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P119F Fuel Rail Pressure Sensor "A" Circuit Out of Range Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

Fuel pressure sensor outputs continuing for at least 0.5 second the voltage that is in the range of 4.75 V to 4.94 V.


Malfunction Duration:

0.5 seconds or more


·

Harness or connector

·

ECM

·

Fuel pressure sensor


Class B1 DTC stored

MONITOR DESCRIPTION

The fuel pressure sensor consistently measures common rail pressure.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P119F Idle the engine for 0.5 seconds or more.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P119F is output A
DTC P119F and other DTC are output B


HINT:

If P0192 or P0193 is output, it may have been detected due to a fuel pressure sensor malfunction.




A

2.CHECK CONNECTOR CONNECTION CONDITION (FUEL PRESSURE SENSOR CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (FUEL PRESSURE SENSOR CONNECTOR)
a.

Check the connector connection for the fuel pressure sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.CHECK FUEL PRESSURE SENSOR

NG

10.CONNECT SECURELY
3.CHECK FUEL PRESSURE SENSOR
a.

Turn the ignition switch off.


b.

Disconnect the fuel pressure sensor connector.


c.

Connect the signal check harness to the ECM and ECM vehicle side harness.


d.

Turn the ignition switch to ON.


A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C04
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness Lead Connector


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E-13 - E-56 Ignition switch ON 4.5 to 5.5 V
E-49 - E-56 Ignition switch ON 4.5 to 5.5 V
E-68 - E-56 Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.CHECK FUEL PRESSURE SENSOR

NG

9.REPLACE ECM
4.CHECK FUEL PRESSURE SENSOR
A405887C04
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness Lead Connector


a.

Turn the ignition switch off.


b.

Connect the fuel pressure sensor connector.


c.

Connect the signal check harness to the ECM and ECM vehicle side harness.


d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E-49 - E-68 Ignition switch ON 0.3 to 0.7 V



Result:
Proceed to
OK
NG



OK

5.CHECK DTC OUTPUT

NG

8.REPLACE COMMON RAIL ASSEMBLY
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P119F is output A
DTCs are not output B




A

6.REPLACE ECM

B

END

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

8.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>COMMON RAIL>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
9.REPLACE ECM
a.

Replace the ECM.


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
10.CONNECT SECURELY
a.

Connect securely the fuel pressure sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT