Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0192  Fuel Rail Pressure Sensor "A" Circuit Low  P0193  Fuel Rail Pressure Sensor "A" Circuit High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0192 Fuel Rail Pressure Sensor "A" Circuit Low Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

Output of the fuel pressure sensor remains at 0.27 V or lower for 1 second or longer.


Malfunction Duration:

1 seconds or more


·

Fuel pressure sensor (built into common rail assembly)

·

Harness or connector

·

ECM


Class B1 DTC stored
P0193 Fuel Rail Pressure Sensor "A" Circuit High Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

Output of the fuel pressure sensor remains at 4.74 V (260 MPa) or higher for 1 second or longer.


Malfunction Duration:

1 seconds or more


·

Fuel pressure sensor (built into common rail assembly)

·

Harness or connector

·

ECM


Class B1 DTC stored

HINT:

When the vehicle runs out of fuel, the ECM determines that the fuel pressure has dropped and P0192 may be stored.


MONITOR DESCRIPTION

The fuel pressure sensor consistently measures common rail pressure.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0192
P0193
Ignition switch ON for 6 seconds or more.


WIRING DIAGRAM

A407164E04
0.625,2.083 1.927,2.302 1.302,0.219 10 false B140 1.594,0.51 2.052,0.708 0.458,0.198 10 false VC1 1.677,1 2.135,1.198 0.458,0.198 10 false E2 1.49,1.479 1.948,1.677 0.458,0.198 10 false PCR1 2.021,0.406 2.479,0.604 0.458,0.198 10 false 1 2.031,0.865 2.438,1.104 0.406,0.24 10 false 3 2.042,1.344 2.448,1.583 0.406,0.24 10 false 2 4.635,0.531 5.094,0.729 0.458,0.198 10 false E-13 4.635,1.01 5.094,1.208 0.458,0.198 10 false E-56 4.646,1.49 5.104,1.688 0.458,0.198 10 false E-49 4.635,1.958 5.094,2.156 0.458,0.198 10 false E-68 4.99,0.531 5.448,0.729 0.458,0.198 10 false B142 4.99,1.01 5.448,1.208 0.458,0.198 10 false B142 4.99,1.49 5.448,1.688 0.458,0.198 10 false B142 4.99,1.969 5.448,2.167 0.458,0.198 10 false B142 5.073,0.333 5.531,0.531 0.458,0.198 10 false 41 5.073,0.823 5.531,1.021 0.458,0.198 10 false 63 5.073,1.292 5.531,1.49 0.458,0.198 10 false 10 5.115,1.771 5.573,1.969 0.458,0.198 10 false 9 5.427,0.51 5.885,0.708 0.458,0.198 10 false VC1 5.438,0.979 5.896,1.177 0.458,0.198 10 false E1 5.438,1.49 5.896,1.688 0.458,0.198 10 false PCR1 5.427,1.958 5.885,2.156 0.458,0.198 10 false PCR2 5.802,2.573 6.26,2.771 0.458,0.198 10 false ECM 0.323,2.281 3.417,2.844 3.094,0.563 10 false Fuel Pressure Sensor (Common Rail Assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization(Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (FUEL PRESSURE SENSOR CONNECTOR)
a.

Check the connector connection for the fuel pressure sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK FUEL PRESSURE SENSOR

NG

13.CONNECT SECURELY
2.CHECK FUEL PRESSURE SENSOR
a.

Check the installation of the fuel pressure sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the sensor.


Result:
Proceed to
OK
NG



OK

3.INSPECT FUEL PRESSURE SENSOR

NG

12.REPLACE COMMON RAIL ASSEMBLY
3.INSPECT FUEL PRESSURE SENSOR
a.

Inspect the fuel pressure sensor.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>COMMON RAIL>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK FUEL PRESSURE SENSOR

NG

12.REPLACE COMMON RAIL ASSEMBLY
4.CHECK FUEL PRESSURE SENSOR
A451756C01
0.313,0.979 0.833,1.229 0.521,0.25 0.958,1.594 1.344,1.135 true 2.385,1.594 2.031,1.104 true 0.167,0.177 0.479,0.375 0.313,0.198 10 false *a 0.406,1.01 0.771,1.25 0.365,0.24 10 false B140 0.688,1.635 1,1.833 0.313,0.198 10 false VC1 2.417,1.635 2.729,1.833 0.313,0.198 10 false E2
*a Front view of wire harness connector
(to Fuel Pressure Sensor)


a.

Disconnect the fuel pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B140-1 (VC1) - B140-3 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

5.CHECK FUEL PRESSURE SENSOR

NG

6.CHECK HARNESS OR CONNECTOR (FUEL PRESSURE SENSOR - ECM)
5.CHECK FUEL PRESSURE SENSOR
A451756C02
0.271,0.896 0.823,1.167 0.552,0.271 1.844,1.74 1.729,1.135 true 1.104,1.781 1.354,1.135 true 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 0.396,0.958 0.802,1.156 0.406,0.198 10 false B140 0.969,1.813 1.281,2.01 0.313,0.198 10 false VC1 1.813,1.792 2.25,1.99 0.438,0.198 10 false PCR1
*a Front view of wire harness connector
(to Fuel Pressure Sensor)


a.

Disconnect the fuel pressure sensor connector.


b.

Turn the ignition switch off.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance::
Tester Connection Switch Condition Specified Condition
B140-1 (VC1) - B140-2 (PCR1) Ignition switch off 200 to 250 kΩ



Result:
Proceed to
OK
NG



OK

8.CHECK DTC OUTPUT

NG

6.CHECK HARNESS OR CONNECTOR (FUEL PRESSURE SENSOR - ECM)
6.CHECK HARNESS OR CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the fuel pressure sensor connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405886C09
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-13 - Body ground and other terminals Always 10 kΩ or higher
E-49 - Body ground and other terminals Always 10 kΩ or higher
E-68 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS OR CONNECTOR (FUEL PRESSURE SENSOR - ECM)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CHECK HARNESS OR CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the fuel pressure sensor connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405886C09
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A451756C03
0.271,0.896 0.802,1.167 0.531,0.271 1.135,1.729 1.385,1.125 true 2.438,1.729 2.021,1.115 true 1.76,1.771 1.729,1.135 true 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 0.396,0.958 0.833,1.156 0.438,0.198 10 false B140 0.917,1.771 1.229,1.969 0.313,0.198 10 false VC1 2.438,1.781 2.75,1.979 0.313,0.198 10 false E1 1.646,1.802 2.104,2 0.458,0.198 10 false PCR1
*a Front view of wire harness connector
(to Fuel Pressure Sensor)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-13 - B140-1 (VC1) Always Below 2 Ω
E-49 - B140-2 (PCR1) Always Below 2 Ω
E-68 - B140-2 (PCR1) Always Below 2 Ω
E-56 - B140-3 (E1) Always Below 2 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK DTC OUTPUT

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P0192 or P0193 is output A
DTCs are not output B




A

9.REPLACE ECM

B

END

9.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
12.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>COMMON RAIL>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
13.CONNECT SECURELY
a.

Connect securely the fuel pressure sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
14.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END