Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P1271  Fuel Pressure Regulator Circuit (Open/Short)  P1272  Fuel Pressure Regulator Circuit (+B Short)  


DESCRIPTION

A208468E34
0.057,0.035 4.208,0.212 4.151,0.177 10 Pressure Discharge Valve Operation Due to Sudden Deceleration: 0.928,0.378 2.056,0.722 1.128,0.343 10 Accelerator Pedal Opening Angle 0.403,1.389 2.038,1.552 1.635,0.163 10 Pressure Discharge Valve 1.132,2.292 2.044,2.455 0.913,0.163 10 Fuel Pressure 2.595,0.546 2.980,0.709 0.385,0.163 10 Open 4.139,1.391 4.524,1.554 0.385,0.163 10 Open 2.595,1.156 3.077,1.319 0.482,0.163 10 Closed 4.139,0.722 4.659,0.885 0.519,0.163 10 Closed 4.22,2.134 6.133,2.276 1.913,0.142 10 w/o Pressure Discharge Valve 1.673,2.706 3.482,2.848 1.809,0.142 10 w/ Pressure Discharge Valve 2.079,3.063 3.430,3.226 1.350,0.163 10 Target Fuel Pressure 3.932,3.287 4.942,3.450 1.010,0.163 10 Time Reduction 3.323,3.528 3.674,3.677 0.350,0.149 10 Time 3.73,2.783 3.499,2.783 false 3.685,3 3.495,3.14 3.495,3.14 3.415,3.14 false 3.898,2.424 4.087,2.224 4.087,2.224 4.183,2.224 false

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1271 Fuel Pressure Regulator Circuit (Open/Short) Diagnosis Condition:
·

Elapse of at least 2 seconds after the ignition switch ON.

·

Battery voltage is in the range of 10 V to 16 V

·

Malfunction about actuator of the injection does not occur.

·

Pressure discharge valve activity request is in progress.


Malfunction Status:

Pressure discharge valve driver current remains short of the specification for at least 2 seconds with the engine runs at 600 rpm.


Malfunction Duration:

2 seconds or more


·

Pressure discharge valve

·

Harness or connector

·

ECM


- DTC stored
P1272 Fuel Pressure Regulator Circuit (+B Short) Diagnosis Condition:
·

Elapse of at least 2 seconds after the ignition switch ON.

·

Battery voltage is in the range of 10 V to 16 V

·

Malfunction about actuator of the injection does not occur.

·

Pressure discharge valve activity request is in progress.


Malfunction Status:

Pressure discharge valve driver current remains short of the specification for at least 2 seconds with the engine runs at 600 rpm.


Malfunction Duration:

2 seconds or more


·

Pressure discharge valve

·

Harness or connector

·

ECM


- DTC stored

HINT:
·

When P1271 and P1272 are output, check the Data List "Actual Common Rail Pressure" using the GTS.

·

P1271:

-

After clearing the DTC, drive the vehicle at 50 km/h in 3rd gear, release the accelerator pedal to decelerate and check that P1271 is not output.


·

P1272:

-

After clearing the DTC, repeat the following procedure 5 times, and then check that P1272 is not stored: Drive the vehicle at 50 km/h in 3rd gear and release the accelerator pedal to decelerate.




Standard:
Condition Actual Common Rail Pressure
Idling after warm-up The "Actual Common Rail Pressure" is within 5000 kPa of the "Target Common Rail Pressure"


MONITOR DESCRIPTION

Pressure discharge valve controls the common rail fuel delivery by releasing the common rail pressure.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P1271
P1272
Turn the ignition switch off from ON and release the accelerator pedal to decelerate after driving at 50 km/h in 3rd gear.

WIRING DIAGRAM

A407169E05
1.615,0.802 2.229,1 0.615,0.198 10 false PRV+ 1.604,1.417 2.219,1.615 0.615,0.198 10 false PRV- 0.844,1.854 1.458,2.052 0.615,0.198 10 false B143 0.844,2.104 2.979,2.406 2.135,0.302 10 false Pressure Discharge Valve 2.177,0.604 2.792,0.802 0.615,0.198 10 false 1 2.177,1.25 2.792,1.448 0.615,0.198 10 false 2 4.594,0.792 5.208,0.99 0.615,0.198 10 false M-60 4.594,1.427 5.208,1.625 0.615,0.198 10 false M-48 4.969,0.802 5.583,1 0.615,0.198 10 false B142 4.969,1.427 5.583,1.625 0.615,0.198 10 false B142 5.052,0.583 5.667,0.781 0.615,0.198 10 false 35 5.052,1.219 5.667,1.417 0.615,0.198 10 false 34 5.813,2.083 6.427,2.281 0.615,0.198 10 false ECM 5.375,0.792 5.99,0.99 0.615,0.198 10 false PC 5.375,1.438 5.99,1.635 0.615,0.198 10 false PRD

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (PRESSURE DISCHARGE VALVE)
a.

Check the connector connection for the pressure discharge valve connector (looseness and poor contact).

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.INSPECT PRESSURE DISCHARGE VALVE

NG

11.CONNECT SECURELY
2.INSPECT PRESSURE DISCHARGE VALVE
a.

Disconnect the pressure discharge valve connector.


b.

Check the pressure discharge valve.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>COMMON RAIL>INSPECTION


A403372C01
0.125,0.135 0.344,0.323 0.219,0.188 10 false *a
*a Component without harness connected
(Pressure Discharge Valve)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - Body ground Always 10 MΩ or higher
2 - Body ground Always 10 MΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS OR CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

NG

10.REPLACE COMMON RAIL ASSEMBLY
3.CHECK HARNESS OR CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C07
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M-60 - Body ground and other terminals Always 10 kΩ or higher
M-48 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS OR CONNECTOR (CHECK FOR OPEN IN WIRE HARNESS)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS OR CONNECTOR (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the pressure discharge valve connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A407232C03
0.302,0.917 0.76,1.188 0.458,0.271 1,1.792 1.521,1.125 true 2.365,1.792 1.875,1.125 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 0.375,0.979 0.844,1.177 0.469,0.198 10 false B143 0.833,1.833 1.323,2.031 0.49,0.198 10 false PRV+ 2.24,1.823 2.729,2.021 0.49,0.198 10 false PRV-
*a Front view of wire harness connector
(to Pressure Discharge Valve)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M-60 - B143-1 (PRV+) Always Below 1 Ω
M-48 - B143-2 (PRV-) Always Below 1 Ω



Result:
Proceed to
OK
NG


A405887C17
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector



OK

5.CHECK DTC OUTPUT

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P1271 or P1272 is output A
DTCs are not output B




A

6.REPLACE ECM

B

END

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
10.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>COMMON RAIL>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
11.CONNECT SECURELY
a.

Connect securely the pressure discharge valve connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT