| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P242B | Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 3 | Diagnosis Condition:
Engine start-up:
·
Battery voltage is in the range of 10 V to 16 V ·
Engine speed 500 rpm or more for at least 5 seconds. ·
Less than 10 seconds has elapsed since start of engine. ·
Difference between engine coolant temperature and intake air temperature is within 10°C (18°F). ·
Difference between engine coolant temperature before ignition switch ON and after ignition switch ON is 20°C (68°F) or more. ·
Engine coolant temperature and intake air temperature are at least -10°C (14°F). Driving
·
At least 10 seconds has elapsed since engine was started. ·
Cumulative exhaust gas flow amount 2 kg or more. ·
Cumulative exhaust gas flow amount of 20 kg or more with after regeneration. ·
After the above -
Battery voltage is in the range of 10 V to 16 V -
Engine speed 500 rpm or more for at least 5 seconds. -
Engine speed 1000 rpm or more -
Exhaust fuel addition injector amount 30 mm3/st/sec or more -
Exhaust gas flow rate 120 kg/h or more -
Difference between engine coolant temperature and intake air temperature is more than 10°C (18°F) ·
In addition, the following conditions continue for at least 10 seconds -
Exhaust fuel addition injector rate variation is within 5 mm3/st. -
Engine speed variation is within 25 rpm/sec. -
Vehicle speed 30 km/h (19 mile) or more. Malfunction Status: Engine start-up:
·
The conditions described below remain for 1 second or more. -
Difference between No. 1 exhaust gas temperature sensor and No. 2 exhaust gas temperature sensor stays less than 70°C (126°F) -
Difference between No. 2 exhaust gas temperature sensor and No. 3 exhaust gas temperature sensor stays more than 70°C (126°F) -
Difference between No. 3 exhaust gas temperature sensor and No. 4 exhaust gas temperature sensor stays more than 70°C (126°F) Driving:
·
Difference between calculated value and actual value of No. 2 exhaust gas temperature sensor is less than 100°C (212°F) for 3 seconds. ·
Difference between calculated value and actual value of No. 3 exhaust gas temperature sensor is not less than 100°C (212°F) for 3 seconds. Malfunction Duration: 3 seconds or more |
·
Sensor or sensing unit ·
ECM |
Class B1 | DTC stored |
The exhaust gas temperature is constantly detected by the No. 3 exhaust gas temperature sensor.
The value of the No. 3 exhaust gas temperature sensor is used to control DPR regeneration.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P242B | Drive for a certain amount of time after starting the engine. |
Refer to DTC P242C.
Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>P242C
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Check for exhaust pipe crack, exhaust gas leak (soot contamination) and improper coupling flange tightening.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the connector connection for the No. 3 exhaust gas temperature sensor connector.
The connector is connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the installation of the No. 3 exhaust gas temperature sensor.
Make sure there is no dirt, damage or clogging in the sensing unit of the No. 3 exhaust gas temperature sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the No. 3 exhaust gas temperature sensor.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 3 Exhaust Gas Temperature Sensor) |
Disconnect the No. 3 exhaust gas temperature sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A111-1 (THC3) - A111-2 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the connector connection for the No. 2 exhaust gas temperature sensor connector.
The connector is connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the installation of the No. 2 exhaust gas temperature sensor.
Make sure there is no dirt, damage or clogging in the sensing unit of the No. 2 exhaust gas temperature sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the No. 2 exhaust gas temperature sensor.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 2 Exhaust Gas Temperature Sensor) |
Disconnect the No. 2 exhaust gas temperature sensor.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch | Specified Condition |
|---|---|---|
| A110-1 (THCO) - A110-2 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the No. 2 exhaust gas temperature sensor connector.
Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)
| *a | Signal Check Harness Lead Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V-46 - Body ground and other terminals | Always | 10 kΩ or higher |
| V-49 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Connect the No. 2 exhaust gas temperature sensor connector.
Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)
| *a | Signal Check Harness Lead Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V-46 - V-49 | Always (20°C) | 13.7 to 29.8 kΩ |
| V-46 - V-49 | Always (50°C) | 7.13 to 13.7 kΩ |
| V-46 - V-49 | Always (80°C) | 4.1 to 7.13 kΩ |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off for 30 seconds or more.
Perform the confirmation driving pattern.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read Current DTCs.
| Result | Proceed to |
|---|---|
| DTC P242B is output | A |
| DTCs are not output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the No. 2 exhaust gas temperature sensor.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the No. 2 exhaust gas temperature sensor.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the No. 2 exhaust gas temperature sensor.
Clean the sensing unit and install it properly.
If damaged, replace the No. 2 exhaust gas temperature sensor.
| Proceed to |
|---|
| NEXT |
NEXT
Connect securely the No. 2 exhaust gas temperature sensor connector.
Repair it as needed.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch off.
Disconnect the No. 3 exhaust gas temperature sensor connector.
Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)
| *a | Signal Check Harness Lead Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V-46 - Body ground and other terminals | Always | 10 kΩ or higher |
| V-69 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Connect the No. 3 exhaust gas temperature sensor connector.
Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)
| *a | Signal Check Harness Lead Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V-46 - V-69 | Always (20°C) | 13.7 to 29.8 kΩ |
| V-46 - V-69 | Always (50°C) | 7.13 to 13.7 kΩ |
| V-46 - V-69 | Always (80°C) | 4.1 to 7.13 kΩ |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off for 30 seconds or more.
Perform the confirmation driving pattern.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read Current DTCs.
| Result | Proceed to |
|---|---|
| DTC P242B is output | A |
| DTCs are not output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the No. 3 exhaust gas temperature sensor.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace No. 3 the exhaust gas temperature sensor.
Clean the sensing unit and install it properly.
If damaged, replace the No. 3 exhaust gas temperature sensor.
| Proceed to |
|---|
| NEXT |
NEXT
Connect securely the No. 3 exhaust gas temperature sensor connector.
Repair it as needed.
| Proceed to |
|---|
| NEXT |
NEXT
Repair the exhaust pipe.
Replace it as needed.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off for 30 seconds or more.
Perform the confirmation driving pattern.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT