Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P2463  Particulate Filter Restriction - Soot Accumulation Bank 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2463 Particulate Filter Restriction - Soot Accumulation Bank 1 Diagnosis Condition:

Ignition switch ON


Malfunction Status:
·

Judge when soot deposit accumulated by ECM reaches the warning level judgment value.

·

Automatic regeneration was not completed for some reason. Then, the DPR light blinked, but manual regeneration was not performed. Or manual regeneration was attempted, but the regeneration did not start and the vehicle continued to be driven.

·

When DPR-clogging was detected by the DPR differential pressure between front and rear not within specifications.


Malfunction Duration:

-


·

DPR light

·

DPR switch

·

Harness or connector

·

ECM


Class C DTC stored

MONITOR DESCRIPTION

ECM constantly calculate and accumulate the amount of soot deposit from the engine.

Moreover, based on the accumulated amount, the regeneration mode is determined.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2463 PM forced regeneration

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P2463 is output A
DTC P2463 and other DTCs are output B




A

2.CHECK DPR INDICATOR LIGHT

B

2.CHECK DPR INDICATOR LIGHT
a.

Turn the ignition switch to ON.


b.

Start the engine.


c.

Check the blinking of the DPR indicator light in the combination meter and the DPR switch light.


Result:
Result Proceed to
DPR indicator light does not blink A
DPR indicator light blinks B



A

3.CHECK DPR INDICATOR LIGHT

B

11.PERFORM PM FORCED REGENERATION
3.CHECK DPR INDICATOR LIGHT
a.

Check the connector connection for the combination meter assembly connector.


b.

Check for broken bulb.


c.

Inspect the harness for disconnections and short-circuits.


Result:
Proceed to
OK
NG



OK

4.INSPECT DIFFERENTIAL PRESSURE SENSOR

NG

10.REPAIR OR REPLACE TROUBLE AREAS
4.INSPECT DIFFERENTIAL PRESSURE SENSOR

Result:
Proceed to
OK
NG



OK

5.CHECK DIFFERENTIAL PRESSURE SENSOR PIPE

NG

9.REPLACE DIFFERENTIAL PRESSURE SENSOR
5.CHECK DIFFERENTIAL PRESSURE SENSOR PIPE
a.

Check the differential pressure sensor pipe for clogging, cracks, and other damage.


Result:
Proceed to
OK
NG



OK

6.CHECK DIFFERENTIAL PRESSURE SENSOR HOSE

NG

8.REPAIR OR REPLACE DIFFERENTIAL PRESSURE SENSOR PIPE
6.CHECK DIFFERENTIAL PRESSURE SENSOR HOSE
a.

Check the differential pressure sensor hose for clogging, cracks, and other damages.


Result:
Proceed to
OK
NG



OK

11.PERFORM PM FORCED REGENERATION

NG

7.REPAIR OR REPLACE DIFFERENTIAL PRESSURE SENSOR HOSE
7.REPAIR OR REPLACE DIFFERENTIAL PRESSURE SENSOR HOSE
a.

Repair or replace the differential pressure sensor pipe.


Result:
Proceed to
NEXT



NEXT

11.PERFORM PM FORCED REGENERATION
8.REPAIR OR REPLACE DIFFERENTIAL PRESSURE SENSOR PIPE
a.

Repair or replace the differential pressure sensor pipe.


Result:
Proceed to
NEXT



NEXT

11.PERFORM PM FORCED REGENERATION
9.REPLACE DIFFERENTIAL PRESSURE SENSOR
a.

Replace the differential pressure sensor.


Result:
Proceed to
NEXT



NEXT

11.PERFORM PM FORCED REGENERATION
10.REPAIR OR REPLACE TROUBLE AREAS
a.

Repair or replace the trouble areas.


Result:
Proceed to
NEXT



NEXT

11.PERFORM PM FORCED REGENERATION
11.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.




Result:
Result Proceed to
Manual forced regeneration started normally A
Manual forced regeneration does not start normally B



A

12.PERFORM PM FORCED REGENERATION

B

14.CHECK DPR SWITCH ASSEMBLY
12.PERFORM PM FORCED REGENERATION
a.

Check if the regeneration normally completes. (Do not activate the accelerator or change the gear position. Or, the regeneration will be aborted.)


b.

The regeneration is complete if idling speed returns to normal and the number of the soot bars in the meter returns to 0.


Result:
Proceed to
OK
NG



OK

END

NG

13.CHECK DTC OUTPUT
13.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P2463 is output A
DTC P2463 and other DTCs are output B




A

11.PERFORM PM FORCED REGENERATION

B

14.CHECK DPR SWITCH ASSEMBLY
a.

Check the connector connection for the DPR switch assembly connector.

Standard:

The connector is connected securely and there are no contact pressure problems.




c.

Check for open or short circuit in wire harness.

Standard:

No open or short circuit in wire harness.



Result:
Proceed to
OK
NG



OK

15.CHECK EXHAUST BRAKE NEUTRAL SWITCH ASSEMBLY OR PARK/NEWTRAL POSITION SWITCH ASSEMBLY

NG

23.REPAIR OR REPLACE TROUBLE AREAS
15.CHECK EXHAUST BRAKE NEUTRAL SWITCH ASSEMBLY OR PARK/NEWTRAL POSITION SWITCH ASSEMBLY
a.

Check the installation of the switch connector.


b.

Inspect the harness for disconnections and short-circuits.


c.

Inspect the switch assembly.

for Manual Transmission:
·

Inspect the exhaust brake neutral switch assembly.

Click hereBrake>EXHAUST BRAKE>EXHAUST BRAKE NEUTRAL SWITCH>INSPECTION


for Automatic Transmission:
·


Result:
Proceed to
OK
NG



OK

16.CHECK ACCELERATOR PEDAL ASSEMBLY

NG

22.REPAIR OR REPLACE TROUBLE AREAS
16.CHECK ACCELERATOR PEDAL ASSEMBLY
a.

Check the installation of the accelerator pedal assembly connector.


b.

Inspect the harness for disconnections and short-circuits.



Result:
Proceed to
OK
NG



OK

17.PERFORM BASIC INSPECTION

NG

21.REPAIR OR REPLACE TROUBLE AREAS
17.PERFORM BASIC INSPECTION
a.

Turn the ignition switch to ON.


b.

Inspect the engine parts and systems based on the engine basic inspection sheet.


Result:
Proceed to
OK
NG



OK

18.PERFORM PM FORCED REGENERATION

NG

20.REPAIR OR REPLACE TROUBLE AREAS
18.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.




Result:
Result Proceed to
Manual forced regeneration started normally A
Manual forced regeneration does not start normally B



A

END

B

19.CHECK DTC OUTPUT
19.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC is output A
DTC is not output B




A

B

END

20.REPAIR OR REPLACE TROUBLE AREAS
a.

Repair or replace the trouble areas.


Result:
Proceed to
NEXT



NEXT

11.PERFORM PM FORCED REGENERATION
21.REPAIR OR REPLACE TROUBLE AREAS
a.

Repair or replace the trouble areas.


Result:
Proceed to
NEXT



NEXT

11.PERFORM PM FORCED REGENERATION
22.REPAIR OR REPLACE TROUBLE AREAS
a.

Repair or replace the trouble areas.


Result:
Proceed to
NEXT



NEXT

11.PERFORM PM FORCED REGENERATION
23.REPAIR OR REPLACE TROUBLE AREAS
a.

Repair or replace the trouble areas.


Result:
Proceed to
NEXT



NEXT

11.PERFORM PM FORCED REGENERATION