Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P007C  Charge Air Cooler Temperature Sensor Circuit Low Bank 1  P007D  Charge Air Cooler Temperature Sensor Circuit High Bank 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P007C Charge Air Cooler Temperature Sensor Circuit Low Bank 1 Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

Output of the intake air temperature sensor (for intercooler side) remains at 0.06 V (200°C (392°F) or less for 3 seconds or longer.


Malfunction Duration:

3 seconds or more


·

Harness or connector

·

Intake air temperature sensor (for intercooler side)

·

ECM


Class B1 DTC stored
P007D Charge Air Cooler Temperature Sensor Circuit High Bank 1 Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.

·

Intake air temperature is -10°C (14°F) or more.


Malfunction Status:

Output of the intake air temperature sensor (for intercooler side) remains at 4.87 V (-35°C (-31°F) or higher for 3 seconds or longer.


Malfunction Duration:

3 seconds or more


·

Harness or connector

·

Intake air temperature sensor (for intercooler side)

·

ECM


Class B1 DTC stored

MONITOR DESCRIPTION

P007C

The intake air temperature sensor (for intercooler side) installed to the downstream of the manifold absolute pressure sensor consistently measures temperature at the outlet of the intercooler.


P007D

The intake air temperature sensor (for intercooler side) installed to the downstream of the manifold absolute pressure sensor consistently measures temperature at the outlet of the intercooler.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P007C
P007D
Ignition switch ON for 3 seconds or more.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connector connection for the intake air temperature sensor (for intercooler side) connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)

NG

14.CONNECT SECURELY
2.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
a.

Check the installation of the intake air temperature sensor (for intercooler side).


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the intake air temperature sensor (for intercooler side).


Result:
Proceed to
OK
NG



OK

3.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)

NG

13.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
3.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
a.

Inspect the intake air temperature sensor (for intercooler side).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS OR CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE) - ECM)

NG

12.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
4.CHECK HARNESS OR CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE) - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the intake air temperature sensor (for intercooler side) connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C12
1.5,0.115 1.875,0.385 0.375,0.271 0.26,0.208 0.573,0.406 0.313,0.198 10 false *a 1.635,0.167 1.792,0.365 0.156,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C07
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-44 - Body ground and other terminals Always 10 kΩ or higher
M-54 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS OR CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE) - ECM)

NG

8.REPLACE ECM
5.CHECK HARNESS OR CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE) - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the intake air temperature sensor (for intercooler side) connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A449990C03
0.323,0.927 0.74,1.208 0.417,0.281 2.375,1.667 1.917,1.271 true 1.052,1.698 1.531,1.281 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.375,0.979 0.74,1.188 0.365,0.208 10 false B148 2.417,1.677 2.781,1.885 0.365,0.208 10 false THG 0.76,1.698 1.125,1.906 0.365,0.208 10 false E2
*a Front view of wire harness connector
(to Intake Air Temperature Sensor (for Intercooler Side))


A405887C12
1.5,0.115 1.875,0.385 0.375,0.271 0.26,0.208 0.573,0.406 0.313,0.198 10 false *a 1.635,0.167 1.792,0.365 0.156,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C07
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-44 - B148-2 (THG) Always Below 1 Ω
M-54 - B148-1 (E2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE) (POWER SOURCE)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE) (POWER SOURCE)
a.

Disconnect the intake air temperature sensor (for intercooler side) connector.


b.

Turn the ignition switch to ON.


c.
A449990C03
0.323,0.927 0.74,1.208 0.417,0.281 2.375,1.667 1.917,1.271 true 1.052,1.698 1.531,1.281 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.375,0.979 0.74,1.188 0.365,0.208 10 false B148 2.417,1.677 2.781,1.885 0.365,0.208 10 false THG 0.76,1.698 1.125,1.906 0.365,0.208 10 false E2
*a Front view of wire harness connector
(to Intake Air Temperature Sensor (for Intercooler Side))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Condition Specified
B148-2 (THG) - B148-1 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

7.CHECK DTC OUTPUT

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P0006 is output A
DTCs are not output B




A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT
9.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT
12.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
a.

Replace intake air temperature sensor (for intercooler side).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT
13.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
a.

Replace or replace the intake air temperature sensor (for intercooler side).

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the intake air temperature sensor (for intercooler side).



Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT
14.CONNECT SECURELY
a.

Connect securely the ambient intake air temperature sensor (for intercooler side) connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT