Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P007B  Charge Air Cooler Temperature Sensor Circuit Range/Performance Bank 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P007B Charge Air Cooler Temperature Sensor Circuit Range/Performance Bank 1 Diagnosis Condition:
Engine start:
·

The following conditions continue for at least 20 seconds:

-

The engine speed is range of 570 to 1000 rpm.

-

Fuel injection rate is at least 4 to 35 mm3/st or less.

-

Engine coolant temperature is in the range of -30 to 55°C (-22 to 131°F).

-

Battery voltage is in the range of 10 V to 16 V



Driving:
·

The conditions described below remain for 11 seconds or more.

-

Battery voltage is in the range of 10 V to 16 V

-

The condition that the engine speed remains at 500 rpm or more for 5 seconds or more.


·

The conditions described below remain for 40 seconds or more.

-

The engine speed is 1200 rpm or more.

-

Fuel injection quantity is 25 mm3/st. or more.

-

A change in the engine speed is 664 rpm or less.

-

A change in fuel injection quantity is 78 mm3/st or less.

-

Atmospheric pressure is higher than 75 kPa.

-

Vehicle speed is 21 km/h (13 mph) or more.

-

Mass air flow rate is 30 gm/s or more.

-

Intake air temperature is -10°C (14°F) or more.

-

Exhaust brake and DPR are not actuated.



Malfunction Status:
Engine start:
·

Judged when the average temperature of the intake air temperature sensor (built into the mass air flow meter) and the intake air temperature sensor (for intercooler side) is 30°C (86°F) or more while the average temperature of the intake air temperature sensor (for intercooler side) and the intake air temperature sensor (for intake manifold side) is 30°C (86°F) or more.


Driving:
·

The calculated intercooler efficiency, which is derived from the intake air temperature sensor, manifold absolute pressure sensor, intake air temperature sensor (for intercooler side), and atmospheric pressure sensor, is greater than 140%.

·

Judged when the calculated EGR cooler efficiency is less than 80%, the difference between the intake manifold temperature and the actual intake air temperature is lower than the specified value (less than 40°C (104°F) when the EGR rate is 0%, less than 47°C (117°F) when the EGR rate is 20% and less than 90°C (194°F) when the EGR rate is 60%), and the calculated intercooler efficiency is lower than the specified value (less than 45% when the vehicle speed is 20 km/h (12 mile/h) or less than 65% when the vehicle speed is 40 km/h (25 mile/h)).


Malfunction Duration:

-


·

Intake air temperature sensor (built into mass air flow meter)

·

Intake air temperature sensor (for intake manifold side)

·

Manifold absolute pressure sensor

·

ECM

·

Intake air temperature sensor (for intercooler side)


Class B1 DTC stored

MONITOR DESCRIPTION

The intake air temperature sensor (for intercooler side), which is installed downstream of the manifold absolute pressure sensor, constantly measures the intake air temperature at the intercooler outlet.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P007B After warming up the engine, drive at an engine speed of 1200 rpm or higher


WIRING DIAGRAM

A407162E19
1.552,0.813 2.01,1.01 0.458,0.198 10 false THG 1.635,1.385 2.094,1.583 0.458,0.198 10 false E2 1.927,0.792 2.385,0.99 0.458,0.198 10 false 2 1.917,1.354 2.375,1.552 0.458,0.198 10 false 1 4.938,0.667 5.396,0.865 0.458,0.198 10 false 2 4.458,0.906 4.917,1.104 0.458,0.198 10 false E-44 4.469,1.49 4.927,1.688 0.458,0.198 10 false M-54 4.823,1.49 5.281,1.688 0.458,0.198 10 false B142 4.833,0.906 5.292,1.104 0.458,0.198 10 false B142 5.646,2.438 6.104,2.635 0.458,0.198 10 false ECM 4.906,1.281 5.365,1.479 0.458,0.198 10 false 85 5.26,0.885 5.719,1.083 0.458,0.198 10 false THAO 5.271,1.448 5.583,1.646 0.313,0.198 10 false E2 0.563,1.896 1.021,2.094 0.458,0.198 10 false B148 0.594,2.104 2.479,2.469 1.885,0.365 10 false Intake Air Temperature Sensor (for Intercooler Side)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read Current DTCs.

Result:
Result Proceed to
DTC P007B is output A
DTC P007B and other DTC are output B


HINT:

If P0234, P0299 or P22D3 is output, it may have been detected due to a turbocharger system or EGR system malfunction.




A

2.CHECK CONNECTOR CONNECTION CONDITION

B

2.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connector connection for the intake air temperature sensor (for intercooler side) connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)

NG

22.CONNECT SECURELY
3.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
a.

Check the installation of the intake air temperature sensor (intercooler outlet).


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the intake air temperature sensor (intercooler outlet).


Result:
Proceed to
OK
NG



OK

4.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)

NG

21.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
4.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
a.

Inspect the intake air temperature sensor (for intercooler side).


Result:
Proceed to
OK
NG



OK

5.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE) (POWER SOURCE)

NG

19.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
5.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE) (POWER SOURCE)
a.

Disconnect the intake air temperature sensor (for intercooler side) connector.


A449990C02
0.323,0.927 0.74,1.208 0.417,0.281 1.083,1.677 1.5,1.26 true 2.229,1.698 1.938,1.271 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.375,0.979 0.74,1.188 0.365,0.208 10 false B148 0.885,1.688 1.344,1.885 0.458,0.198 10 false E2 2.25,1.708 2.708,1.906 0.458,0.198 10 false THG
*a Front view of wire harness connector
(to Intake Air Temperature Sensor (for Intercooler Side))


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B148-2 (THG) - B148-1 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

8.CHECK INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER)

NG

6.CHECK HARNESS OR CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE) - ECU)
6.CHECK HARNESS OR CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE) - ECU)
a.

Disconnect the ECM connector.


b.

Disconnect the intake air temperature sensor (for intercooler side) connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C11
1.479,0.115 1.896,0.396 0.417,0.281 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 1.635,0.156 1.792,0.354 0.156,0.198 10 false E
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-44 - Other terminals and Body ground Always 10 kΩ or higher
M-54 - Other terminals and Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


A405887C07
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector



OK

7.CHECK HARNESS OR CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE) - ECU)

NG

17.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CHECK HARNESS OR CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE) - ECU)
a.

Disconnect the ECM connector.


b.

Disconnect the intake air temperature sensor (for intercooler side) connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A449990C02
0.323,0.927 0.74,1.208 0.417,0.281 1.083,1.677 1.5,1.26 true 2.229,1.698 1.938,1.271 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.375,0.979 0.74,1.188 0.365,0.208 10 false B148 0.885,1.688 1.344,1.885 0.458,0.198 10 false E2 2.25,1.708 2.708,1.906 0.458,0.198 10 false THG
*a Front view of wire harness connector
(to Intake Air Temperature Sensor (for Intercooler Side))


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-44 - B148-2 (THG) Always 10 kΩ or higher
M-54 - B148-1 (E2) Always 10 kΩ or higher



Result:
Proceed to
OK
NG


A405887C11
1.479,0.115 1.896,0.396 0.417,0.281 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 1.635,0.156 1.792,0.354 0.156,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C07
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector



OK

8.CHECK INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER)

NG

17.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.CHECK INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER)
a.

Check the installation of the intake air temperature sensor (built into mass air flow meter).


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the intake air temperature sensor (built into mass air flow meter).


Result:
Proceed to
OK
NG



OK

9.INSPECT INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER)

NG

25.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER)
9.INSPECT INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER)
a.

Inspect the intake air temperature sensor (built into mass air flow meter).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

24.REPLACE INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER)
10.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Check the installation of the manifold absolute pressure sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the manifold absolute pressure sensor.


Result:
Proceed to
OK
NG



OK

11.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

23.REPAIR OR REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
11.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


A241069C38
0.281,1.115 0.771,1.406 0.49,0.292 0.99,1.76 1.406,1.344 true 2.208,1.75 1.844,1.354 true 0.854,1.771 1.01,1.969 0.156,0.198 10 false E 2.271,1.771 2.583,1.99 0.313,0.219 10 false VC 0.417,1.188 0.708,1.458 0.292,0.271 10 false B18 0.25,0.25 0.51,0.448 0.26,0.198 10 false *a
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B18-3 (VC) - B18-1 (E) Ignition switch ON 4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

12.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)

NG

GO TO MANIFOLD ABSOLUTE PRESSURE SENSOR POWER SOURCE

12.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Check the installation of the intake air temperature sensor (for intake manifold side).


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the intake air temperature sensor (for intake manifold side).


Result:
Proceed to
OK
NG



OK

13.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)

NG

20.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
13.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Inspect the intake air temperature sensor (for intake manifold side).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

14.CHECK DTC OUTPUT

NG

18.REPLACE INTAKE AIR TEMPERATURE SENSOR (for Intake Manifold Side)
14.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P007B is output A
DTCs are not output B




A

15.REPLACE ECM

B

16.CHECK DTC OUTPUT
15.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
16.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

17.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
18.REPLACE INTAKE AIR TEMPERATURE SENSOR (for Intake Manifold Side)
a.

Replace the intake air temperature sensor (for intake manifold side).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
19.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
a.

Replace the intake air temperature sensor (for intercooler side).


Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
20.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Repair or replace the intake air temperature sensor (for intake manifold side).

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the intake air temperature sensor (for intake manifold side).



Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
21.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTERCOOLER SIDE)
a.

Repair or replace the intake air temperature sensor (for intercooler side).

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the intake air temperature sensor (for intercooler side).



Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
22.CONNECT SECURELY
a.

Connect securely the intake air temperature sensor (for intercooler side) connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
23.REPAIR OR REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Repair or replace the manifold absolute pressure sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the manifold absolute pressure sensor.



Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
24.REPLACE INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER)
a.

Replace the intake air temperature sensor (built into mass air flow meter).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
25.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER)
a.

Repair or replace the intake air temperature sensor (built into mass air flow meter).

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the intake air temperature sensor (built into mass air flow meter).



Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT