Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0652  Sensor Reference Voltage "B" Circuit Low  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0652 Sensor Reference Voltage "B" Circuit Low Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V


Malfunction Status:

Power supply voltage no greater than 3.5 V for at least 3 seconds.


Malfunction Duration:

3 seconds or more


·

Harness or connector

·

Mass air flow meter

·

Accelerator pedal assembly

·

Camshaft position sensor

·

ECM


Class B1 DTC stored

MONITOR DESCRIPTION

Power is supplied to the sensor supply 2 circuit.

(Mass air flow meter, accelerator pedal position sensor, camshaft position sensor)

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0652 Ignition switch ON for 8 seconds or more.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and disconnect the intake mass air flow meter sub-assembly connector.


f.

Perform the confirmation driving pattern.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read the DTCs.

Result:
Result Proceed to
DTC P0652 is output A
DTCs are not output B




A

2.CHECK DTC OUTPUT

B

10.REPLACE MASS AIR FLOW METER
2.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and disconnect the accelerator pedal assembly connector.


f.

Perform the confirmation driving pattern.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read the DTCs.

Result:
Result Proceed to
DTC P0652 is output A
DTCs are not output B




A

3.CHECK DTC OUTPUT

B

9.REPLACE ACCELERATOR PEDAL ASSEMBLY
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and disconnect the camshaft position sensor connector.


f.

Perform the confirmation driving pattern.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read the DTCs.

Result:
Result Proceed to
DTC P0652 is output A
DTCs are not output B




A

4.CHECK HARNESS OR CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

B

8.REPLACE CAMSHAFT POSITION SENSOR
4.CHECK HARNESS OR CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
A405886C12
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


a.

Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-74 - Body ground and other terminals Always 10 kΩ or higher
V-50 - Body ground and other terminals Always 10 kΩ or higher
E-53 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
8.REPLACE CAMSHAFT POSITION SENSOR

Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
9.REPLACE ACCELERATOR PEDAL ASSEMBLY
a.

Replace the accelerator pedal assembly.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
10.REPLACE MASS AIR FLOW METER

Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT