Home › Engine / Hybrid System › N04C-WA (EMISSION CONTROL) › UREA SELECTIVE CATALYTIC REDUCTION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082614 N04C-WA EMISSION CONTROL _0400651 UREA SELECTIVE CATALYTIC REDUCTION SYSTEM C

N04C-WA EMISSION CONTROL  UREA SELECTIVE CATALYTIC REDUCTION SYSTEM  P202E71  Reductant Injection Valve Circuit Range/Performance Bank 1 Unit 1 Actuator Stuck  


DESCRIPTION

The urea solution injection volume is diagnosed as abnormal.

The urea solution injection volume is controlled by the urea solution pressure and the opening of the urea injector assembly.

A444326C01
3,0.948 3.135,0.948 3.135,0.948 3.896,1.917 true 3.417,0.708 3.573,0.708 3.573,0.708 4.26,1.708 true 3.813,0.542 3.927,0.542 3.927,0.542 4.594,1.865 true 4.24,0.427 4.417,0.427 4.417,0.427 4.708,1.865 true 2.823,1.74 3,1.74 3,1.74 3.396,1.927 true 2.823,1.417 3,1.417 3,1.417 3.563,1.885 true 1.51,2.167 1.823,2.323 0.313,0.156 10 false *1 2.792,2.708 3.104,2.865 0.313,0.156 10 false *2 3.656,2.646 3.969,2.802 0.313,0.156 10 false *3 4.281,2.292 4.594,2.448 0.313,0.156 10 false *4 2.823,0.875 3.135,1.031 0.313,0.156 10 false *5 3.271,0.635 3.583,0.792 0.313,0.156 10 false *6 2.625,1.313 2.938,1.469 0.313,0.156 10 false *7 4.083,0.344 4.396,0.5 0.313,0.156 10 false *8 3.448,2.302 3.76,2.458 0.313,0.156 10 false *9 2.552,1.667 2.885,1.865 0.333,0.198 10 false *10 6.073,1.958 6.542,2.115 0.469,0.156 10 false *11 3.635,0.469 3.948,0.625 0.313,0.156 10 false *7
*1 Muffler *2 Urea Injector Assembly
*3 Urea Tube with Heater Assembly *4 Urea Pump
*5 Pressure Sensor *6 Pump Motor
*7 Temperature Sensor *8 Level Sensor
*9 Urea Sensor Assembly *10 Urea Solution Quality Sensor
*11 Urea Tank - -


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P202E71 Reductant Injection Valve Circuit Range/Performance Bank 1 Unit 1 Actuator Stuck Diagnosis Condition:
·

The total urea solution injection volume is higher than 0.545 g.

·

Ambient temperature is higher than -7°C (19.4°F).

·

Atmospheric pressure is higher than 75 kPa (10.9 psi).

·

The battery voltage is 9 to 16 V.


Malfunction Status:
·

The estimated urea solution injection volume is 20% or less of the requested urea solution injection volume.


Malfunction Duration:
·

-


·

Open or short in urea injector assembly circuit

·

Urea injector assembly

·

Urea tube with heater assembly

·

DCU (emission control ECU assembly)


Class A AdBlue consumption warning light:
Comes on
DTC stored

MONITOR DESCRIPTION

Description of malfunction

Failure of urea injector assembly at system startup is detected.


Reset condition

After having restored to the normal conditions.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P202E71 Perform "Pattern 2" of the "Reductant Injection" Utility.

WIRING DIAGRAM

A444325E01
0.958,1.604 2.76,1.854 1.802,0.25 10 false Urea Injector Assembly 0.969,1.427 2.344,1.625 1.375,0.198 10 false A114 5.438,2.146 6.875,2.51 1.438,0.365 10 false DCU (Emission Control ECU Assembly) 5.208,0.573 5.51,0.74 0.302,0.167 10 false P12 5.208,1.115 5.51,1.281 0.302,0.167 10 false P12 5.208,1.646 5.51,1.813 0.302,0.167 10 false P12 5.594,0.583 5.979,0.75 0.385,0.167 10 false UIV+ 5.583,1.115 5.969,1.281 0.385,0.167 10 false UIV- 5.583,1.656 5.969,1.823 0.385,0.167 10 false ISG 5.271,0.375 5.469,0.552 0.198,0.177 10 false 6 5.281,0.896 5.479,1.073 0.198,0.177 10 false 7 5.24,1.448 5.438,1.625 0.198,0.177 10 false 37 4.844,0.583 5.125,0.771 0.281,0.188 10 false E-6 4.833,1.125 5.104,1.302 0.271,0.177 10 false E-7 4.802,1.656 5.146,1.823 0.344,0.167 10 false E-37 3.823,1.802 4.552,1.979 0.729,0.177 10 false Shielded 1.271,1.115 1.656,1.281 0.385,0.167 10 false UIV+ 1.823,1.115 2.208,1.281 0.385,0.167 10 false UIV- 2.208,1 2.406,1.177 0.198,0.177 10 false 1 1.063,0.99 1.26,1.167 0.198,0.177 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
Handling urea solution
·

Wear protective equipment as necessary (protective glasses and gloves).

·

Do not dilute urea solution.

·

If urea solution contacts your eyes or skin, immediately wash the contacted area with a large amount of water and consult a doctor as necessary.

·

If urea solution dries, it deposits a white powder. Also, if urea solution contacts metals such as copper and aluminum for a long period of time, it may promote corrosion. Therefore, if urea solution is spilled, dampen a cloth or other item and wipe it up or rinse the area with cool or warm water.


Handling the urea injector assembly
·

The urea injector assembly is a precision instrument. Take necessary precautions for installation and shipping. Do not use the part if it has been struck or dropped.

·

If the urea solution remaining inside the urea injector assembly dries out, it may become unable to inject urea solution. Therefore, conduct urea tube with heater assembly installation and removal quickly.

·

If the urea solution dries out and deposition occurs, urea may cling to the O-ring of the pipe and cause seal problems. Therefore, clean the urea tube with heater assembly and intake port of the urea injector assembly with water before attaching them.

·

Perform this procedure in an environment where urea solution will not freeze.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT UREA TUBE WITH HEATER ASSEMBLY
a.

While checking the refill check tube, refill the urea solution until the tank level is half full or more.


b.

Disconnect the urea tube with heater assembly from the urea injector assembly.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA INJECTOR>REMOVAL

NOTICE:

If the urea solution remaining inside the urea injector assembly dries out, it may become unable to inject urea solution. Therefore, seal the urea injector assembly with an item such as a cover or rubber cap so that the inside does not dry out.



c.

Prepare a bucket or other receptacle for collecting urea solution from the urea tube with heater assembly.


d.

Connect the GTS to the DLC3.


e.

Turn the ignition switch to ON.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Reductant Discharge.


h.

Perform the Utility and check the Reductant Pump Pressure.


Result:
Result Proceed to
Except below A
Reductant Pump Pressure is 4.5 to 5.5 bar B


HINT:

If the Utility fails, troubleshoot the error message and perform the Utility again.



A

2.CHECK FOR UREA SOLUTION LEAKS

B

16.REPLACE UREA TUBE WITH HEATER ASSEMBLY
2.CHECK FOR UREA SOLUTION LEAKS
a.

Remove the urea injector assembly from the front exhaust pipe assembly.

HINT:
·

Do not disconnect the urea injector assembly from the urea tube with heater assembly.

·

Use a cover, etc., to prevent foreign matter from entering the exhaust pipe.




b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Pressure Rising Diagnosis (Leak Test).


f.

Perform the Utility and check that there are no urea solution leaks in the urea injector assembly and the area from the urea injector assembly to the urea pump.


OK:

No urea solution leaks in urea injector assembly and area from urea injector assembly to urea pump.


Result:
Proceed to
OK
NG


HINT:

If the Utility fails, troubleshoot the error message and perform the Utility again.



OK

3.INSPECT UREA INJECTOR ASSEMBLY

NG

14.REPAIR UREA SOLUTION LEAKS
3.INSPECT UREA INJECTOR ASSEMBLY
a.

While checking the refill check tube, refill the urea solution until the tank level is half full or more.


b.

Remove the urea injector assembly from the front exhaust pipe assembly.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA INJECTOR>REMOVAL

HINT:
·

Do not disconnect the urea injector assembly from the urea tube with heater assembly.

·

Use a cover, etc., to prevent foreign matter from entering the exhaust pipe.




c.

Prepare a bucket or other receptacle for collecting urea solution from the urea injector assembly.


d.

Connect the GTS to the DLC3.


e.

Turn the ignition switch to ON.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Reductant Injection / Pattern 3.


h.

Perform "Pattern 3" and check the urea solution injection.


OK:

Urea solution injects from urea injector assembly.


Result:
Proceed to
OK
NG



OK

4.CHECK UREA SOLUTION INJECTION VOLUME

NG

12.PERFORM INJECTOR REFRESH
4.CHECK UREA SOLUTION INJECTION VOLUME
a.

While checking the refill check tube, refill the urea solution until the tank level is half full or more.


b.

Remove the urea injector assembly from the front exhaust pipe assembly.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA INJECTOR>REMOVAL

HINT:
·

Do not disconnect the urea injector assembly from the urea tube with heater assembly.

·

Use a cover, etc., to prevent foreign matter from entering the exhaust pipe.




c.

Prepare a bucket or other receptacle for collecting urea solution from the urea injector assembly.


d.

Connect the GTS to the DLC3.


e.

Turn the ignition switch to ON.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Reductant Injection / Pattern 3.


h.

Perform "Pattern 3" and check the urea solution injection volume.

Standard Value:
Reductant Injection Urea Solution Injection Volume
Pattern 3 45 to 55 cc


NOTICE:

The measured value is within the standard value at least once during 3 times.


HINT:

Crystallized urea solution dissolves in urea solution, so blockages can be cleared by repeatedly supplying and injecting urea solution.

Therefore, even if crystals accumulate on the tip of the injector, the above injection is possible and it is not a malfunction.



Result:
Proceed to
OK
NG



OK

5.CHECK UREA SOLUTION INJECTION VOLUME

NG

7.CHECK HARNESS AND CONNECTOR (UREA INJECTOR ASSEMBLY - DCU (EMISSION CONTROL ECU ASSEMBLY))
5.CHECK UREA SOLUTION INJECTION VOLUME
a.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Reductant Injection / Pattern 2.


b.

Perform "Pattern 2" and check the urea solution injection volume.


Standard Value:
Reductant Injection Urea Solution Injection Volume
Pattern 2 16 to 24 cc


Result:
Proceed to
OK
NG



OK

6.CHECK UREA SOLUTION INJECTION VOLUME

NG

7.CHECK HARNESS AND CONNECTOR (UREA INJECTOR ASSEMBLY - DCU (EMISSION CONTROL ECU ASSEMBLY))
6.CHECK UREA SOLUTION INJECTION VOLUME
a.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Reductant Injection / Pattern 1.


b.

Perform "Pattern 1" and check the urea solution injection volume.


Standard Value:
Reductant Injection Urea Solution Injection Volume
Pattern 1 7 to 13 cc


Result:
Proceed to
OK
NG


HINT:

When the urea solution injection volume is within the standard range, blockages caused by crystallized urea solution have been cleared.



OK

19.CLEAR DTC

NG

7.CHECK HARNESS AND CONNECTOR (UREA INJECTOR ASSEMBLY - DCU (EMISSION CONTROL ECU ASSEMBLY))
7.CHECK HARNESS AND CONNECTOR (UREA INJECTOR ASSEMBLY - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-6 (UIV+) - E-7 (UIV-) Ignition switch off 17 Ω or less



Result:
Result Proceed to
NG A
OK B



A

8.INSPECT UREA INJECTOR ASSEMBLY

B

11.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
8.INSPECT UREA INJECTOR ASSEMBLY
a.

Result:
Proceed to
OK
NG



OK

9.REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

10.REPLACE UREA INJECTOR ASSEMBLY
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CHECK UREA SOLUTION INJECTION VOLUME
10.REPLACE UREA INJECTOR ASSEMBLY
a.

Replace the urea injector assembly.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CHECK UREA SOLUTION INJECTION VOLUME
11.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Replace the DCU (emission control ECU assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CHECK UREA SOLUTION INJECTION VOLUME
12.PERFORM INJECTOR REFRESH
NOTICE:

Injector Refresh takes approximately 40 minutes to complete. Therefore, perform the procedure somewhere the vehicle can be parked for a long period of time.


a.

While checking the refill check tube, refill the urea solution until the tank level is half full or more.


b.

Remove the urea injector assembly from the front exhaust pipe assembly.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA INJECTOR>REMOVAL

HINT:
·

Do not disconnect the urea injector assembly from the urea tube with heater assembly.

·

Use a cover, etc., to prevent foreign matter from entering the exhaust pipe.




c.

Prepare a bucket or other receptacle for collecting urea solution from the urea injector assembly.


d.

Connect the GTS to the DLC3.


e.

Turn the ignition switch to ON.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Injector Refresh.


h.

Perform the Injector Refresh.


OK:

Injector Refresh is complete.


HINT:

If the Utility fails, troubleshoot the error message and perform the Utility again.


Result:
Proceed to
NEXT



NEXT

13.CHECK UREA SOLUTION INJECTION VOLUME
13.CHECK UREA SOLUTION INJECTION VOLUME
a.

While checking the refill check tube, refill the urea solution until the tank level is half full or more.


b.

Remove the urea injector assembly from the front exhaust pipe assembly.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA INJECTOR>REMOVAL

HINT:
·

Do not disconnect the urea injector assembly from the urea tube with heater assembly.

·

Use a cover, etc., to prevent foreign matter from entering the exhaust pipe.




c.

Prepare a bucket or other receptacle for collecting urea solution from the urea injector assembly.


d.

Connect the GTS to the DLC3.


e.

Turn the ignition switch to ON.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Reductant Injection / Pattern 1 to 3.


h.

Perform "Pattern 1" to "Pattern 3" and check the urea solution injection volume.


Standard Value:
Reductant Injection Urea Solution Injection Volume
Pattern 3 45 to 55 cc
Pattern 2 16 to 24 cc
Pattern 1 7 to 13 cc


Result:
Proceed to
OK
NG



OK

19.CLEAR DTC

NG

15.CHECK INSPECTION RESULT
14.REPAIR UREA SOLUTION LEAKS
a.

Repair the urea solution leaks.


Result:
Proceed to
NEXT



NEXT

13.CHECK UREA SOLUTION INJECTION VOLUME
15.CHECK INSPECTION RESULT
Inspection Result:
Result Proceed to
When the urea tube with heater assembly is already replaced in step 1, abnormality in other parts can be suspected. Perform the check again. A
When the injector refresh is already performed in step 12, replace the urea injector assembly. B
When the urea injector assembly and urea tube with heater assembly are already replaced in steps 2 and 8, replace the DCU (emission control ECU assembly). C



A

2.CHECK FOR UREA SOLUTION LEAKS

B

17.REPLACE UREA INJECTOR ASSEMBLY

C

18.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
16.REPLACE UREA TUBE WITH HEATER ASSEMBLY
a.

Replace the urea tube with heater assembly.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA TUBE>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CHECK UREA SOLUTION INJECTION VOLUME
17.REPLACE UREA INJECTOR ASSEMBLY
a.

Replace the urea injector assembly.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

19.CLEAR DTC
18.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Replace the DCU (emission control ECU assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

19.CLEAR DTC
19.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

20.CHECK WHETHER DTC OUTPUT RECURS (DTC P202E71)
20.CHECK WHETHER DTC OUTPUT RECURS (DTC P202E71)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

OK:

DTCs are not output



Result:
Proceed to
NEXT



NEXT

END