Home › Engine / Hybrid System › N04C-WA (EMISSION CONTROL) › UREA SELECTIVE CATALYTIC REDUCTION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082614 N04C-WA EMISSION CONTROL _0400651 UREA SELECTIVE CATALYTIC REDUCTION SYSTEM C

N04C-WA EMISSION CONTROL  UREA SELECTIVE CATALYTIC REDUCTION SYSTEM  P204D15  Reductant Pressure Sensor Circuit High Circuit Short to Battery or Open  


DESCRIPTION

The pressure sensor embedded in the urea pump is used to check the pressure in the urea pump.

Disconnections and short circuits in the pressure sensor of the urea pump are detected by the DCU (emission control ECU assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P204D15 Reductant Pressure Sensor Circuit High Circuit Short to Battery or Open Diagnosis Condition:
·

Ignition switch ON.


Malfunction Status:
·

The pressure sensor voltage is higher than 4.763 V.


Malfunction Duration:
·

3 seconds or more.


·

Open or short in pressure sensor (urea pump) circuit

·

Pressure sensor (urea pump)

·

DCU (emission control ECU assembly)


Class A AdBlue consumption warning light:
Comes on
DTC stored

MONITOR DESCRIPTION

Description of malfunction

High voltage abnormality is detected in the pressure sensor located in the urea pump.


Reset condition

Procedure to turn off MIL and AdBlue consumption warning light by returning system to normal.

With the urea solution not frozen, start the engine.

When the exhaust gas temperature is 160°C (320°F) or more, the urea SCR system starts and diagnosis of the urea pump and urea injector assembly is performed. After diagnosis is complete, stop the engine.

Repeat the above procedure 3 times.

When the urea SCR system determines that it is normal after starting 1 time, the illuminated MIL remains illuminated and the AdBlue consumption warning light turns off. When the urea SCR system determines that it is normal after starting 3 times, the MIL turns off.


Procedure to turn off MIL and AdBlue consumption warning light after repairs.

After repairs are complete, connect the GTS and clear* the urea SCR system DTCs.

When the engine starts, check that the MIL illuminates and the AdBlue consumption warning light turns off. After 1 minute elapses, stop the engine. Start the engine again and check that the MIL turns off and the system returns to normal.

(*: The ECM malfunction information is not cleared, even if the urea SCR system DTCs are cleared. However, the command that caused the MIL to continuously illuminate is cleared.)



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P204D15 Ignition switch ON for 5 seconds or more.

WIRING DIAGRAM

·

For the circuit diagram of the pressure sensor (urea pump) refer to the DTC P0642A2.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0642A2

·

For the circuit diagram of the DCU (emission control ECU assembly) power source refer to the DTC P0562A2.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0562A2

·

For the circuit diagram of the VCPU terminal refer to the DTC P0642A2.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0642A2

·

For the circuit diagram of the VCLU terminal refer to the DTC P0652A2.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0652A2


CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (PRESSURE SENSOR (UREA PUMP))
a.

Check the connector connection and contact pressure of the pressure sensor (urea pump) connector.

OK:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR (UREA PUMP) - DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

15.CONNECT SECURELY
2.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR (UREA PUMP) - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


A405887C01
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


A360358C15
1.479,0.833 1.896,1.094 0.417,0.26 1.656,1.625 1.135,2.542 true 1.781,1.625 1.917,2.563 true 1.969,1.625 2.615,2.531 true 0.146,0.177 0.458,0.375 0.313,0.198 10 false *a 1.573,0.896 1.885,1.094 0.313,0.198 10 false P11 1.844,2.594 2.167,2.823 0.323,0.229 10 false PU 0.969,2.563 1.417,2.781 0.448,0.219 10 false VCPU 2.594,2.583 3.073,2.802 0.479,0.219 10 false EPU
*a Front view of wire harness connector
(to Pressure Sensor (Urea Pump))


Disconnect the pressure sensor (urea pump) connector.


b.

Disconnect the DCU (emission control ECU assembly) connector.


c.

Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-25 (VCPU) - P11-5 (VCPU) Ignition switch off Below 1 Ω
E-44 (EPU) - P11-3 (EPU) Ignition switch off Below 1 Ω
E-56 (PU) - P11-4 (PU) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR (UREA PUMP) - DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

14.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR (UREA PUMP) - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


A405887C01
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


Disconnect the urea pump connector.


b.

Disconnect the DCU (emission control ECU assembly) connector.


c.

Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-25 (VCPU) - Body ground Ignition switch off 10 kΩ or higher
E-44 (EPU) - Body ground Ignition switch off 10 kΩ or higher
E-56 (PU) - Body ground Ignition switch off 10 kΩ or higher
E-56 (PU) - E-17 (+BU1) Ignition switch off 10 kΩ or higher
E-56 (PU) - E-18 (+BU2) Ignition switch off 10 kΩ or higher
E-56 (PU) - E-19 (+BU3) Ignition switch off 10 kΩ or higher
E-56 (PU) - E-33 (+BU4) Ignition switch off 10 kΩ or higher
E-56 (PU) - E-51 (+BU5) Ignition switch off 10 kΩ or higher
E-56 (PU) - E-52 (PB3) Ignition switch off 10 kΩ or higher
E-56 (PU) - E-24 (VCLU) Ignition switch off 10 kΩ or higher
E-56 (PU) - E-25 (VCPU) Ignition switch off 10 kΩ or higher
E-56 (PU) - E-30 (BATT) Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK PRESSURE SENSOR (UREA PUMP)

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK PRESSURE SENSOR (UREA PUMP)
a.
A355506C08
0.771,1.75 1.292,1.042 true 1.448,1.74 1.542,1.042 true 2.417,1.75 1.906,1.031 true 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 0.573,1.802 1.135,2.063 0.563,0.26 10 false EPU 1.333,1.802 1.844,2.042 0.51,0.24 10 false PU 2.302,1.781 2.865,2.01 0.563,0.229 10 false VCPU
*a Component without harness connected
(Pressure Sensor (Urea Pump))


Disconnect the pressure sensor (urea pump) connector.


b.

Check that the pressure sensor (urea pump) terminal is free of bending and damage.

OK:

Pressure sensor (urea pump) terminal is free of bending and damage.



Result:
Proceed to
OK
NG



OK

5.CHECK DCU (EMISSION CONTROL ECU ASSEMBLY)

NG

12.REPLACE PRESSURE SENSOR (UREA PUMP)
5.CHECK DCU (EMISSION CONTROL ECU ASSEMBLY)
a.
A444330C01
1.875,1.854 1.573,1.385 true 1,1.896 1.417,1.479 true 2.531,1.875 1.583,1.115 true 0.156,0.125 0.469,0.281 0.313,0.156 10 false *a 2.469,1.906 3.083,2.104 0.615,0.198 10 false VCPU 1.802,1.906 2.219,2.115 0.417,0.208 10 false EPU 0.896,1.938 1.51,2.135 0.615,0.198 10 false PU
*a Component without harness connected
(DCU (Emission Control ECU Assembly))


Disconnect the DCU (emission control ECU assembly) connector.


b.

Check that the DCU (emission control ECU assembly) terminal is free of bending and damage.

OK:

DCU (emission control ECU assembly) terminal is free of bending and damage.



Result:
Proceed to
OK
NG



OK

6.CLEAR DTC

NG

11.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
6.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P204D15)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P204D15)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
DTC P204D15 is output A
DTCs are not output B




A

8.REPLACE PRESSURE SENSOR (UREA PUMP)

B

END

8.REPLACE PRESSURE SENSOR (UREA PUMP)
a.

Replace the pressure sensor (urea pump).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CLEAR DTC
9.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P204D15)
10.CHECK WHETHER DTC OUTPUT RECURS (DTC P204D15)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
DTC P204D15 is output A
DTCs are not output B




A

11.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)

B

END

11.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Replace the DCU (emission control ECU assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.CLEAR DTC
12.REPLACE PRESSURE SENSOR (UREA PUMP)
a.

Replace the pressure sensor (urea pump).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.CLEAR DTC
13.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

16.CLEAR DTC
14.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

16.CLEAR DTC
15.CONNECT SECURELY
a.

Securely connect the pressure sensor (urea pump) connector.

HINT:

Repair parts as necessary.



Result:
Proceed to
NEXT



NEXT

16.CLEAR DTC
16.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

17.CHECK WHETHER DTC OUTPUT RECURS (DTC P204D15)
17.CHECK WHETHER DTC OUTPUT RECURS (DTC P204D15)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

OK:

DTCs are not output



Result:
Proceed to
NEXT



NEXT

END