Home › Engine / Hybrid System › N04C-VL (ENGINE MECHANICAL) › ENGINE › from 2019.08
RM2850E _51 Engine / Hybrid System _073160 N04C-VL ENGINE MECHANICAL _0355999 ENGINE G

N04C-VL ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 17700 4.INSPECT AIR CLEANER ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly.


b.

Visually check that there is no dirt, blockage, or damage to the air cleaner filter element.

HINT:
·

If there is any dirt or blockage in the air cleaner filter element, clean it with compressed air.

·

If any dirt or blockage remains even after cleaning the air cleaner filter element with compressed air, replace it.




Hide 5.INSPECT ENGINE IDLE SPEED AND MAXIMUM SPEED

NOTICE:

Turn all the electrical systems and the A/C OFF.


a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

HINT:

Refer to the GTS operator manual for further information regarding the selection of Data List.



iv.

Check the engine idle speed.

Standard Idle Speed:

600 to 700 rpm



v.

Fully depress the accelerator pedal.


vi.

Check the maximum speed.

Maximum Speed:

3610 to 3690 rpm



vii.

Turn the ignition switch off.


viii.

Disconnect the GTS from the DLC3.



c.

When not using the GTS:

i.
A118802C01
0.344,1.626 0.509,1.876 0.165,0.25 10 *1 0.964,1.481 0.552,1.694 false
*1 TAC


Install SST to terminal (TAC) of DLC3, then connect a tachometer.

SST
09843-18040  

NOTICE:

Make sure the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.



ii.

Turn the ignition switch to ON.


iii.

Check the engine idle speed.

Standard Idle Speed:

600 to 700 rpm



iv.

Fully depress the accelerator pedal.


v.

Check the maximum speed.

Maximum Speed:

3610 to 3690 rpm



vi.

Turn the ignition switch off.


vii.

Disconnect the tachometer.


viii.

Remove SST from terminal.



Hide 6.INSPECT COMPRESSION

a.

Warm up and stop the engine.


b.

Remove the 4 bolts from the 4 glow plug holes.


c.

Remove the oil filler cap.


d.

Remove the No. 1 engine cover sub-assembly.

(Click hereEngine / Hybrid System>N04C-VL (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL)


e.

Disconnect all connectors from the 4 injectors.


f.

Crank the engine to remove foreign matter before measuring the compression.


g.

Install the attachment into the glow plug hole.


h.

Connect a compression gauge to SST.

SST
09992-78010  


i.

While cranking the engine, measure the compression pressure.

Compression Pressure (Engine speed at 280 rpm):

3200 kPa (33 kgf/cm2 464 psi)

Minimum Pressure (Engine speed at 280 rpm):

2700 kPa (28 kgf/cm2 392 psi)

Difference between Each Cylinder:

290 kPa (3 kgf/cm2 42 psi)


NOTICE:
·

Use a fully-charged battery so that the engine speed can be increased to 280 rpm or more.

·

Inspect the other cylinders in the same way.

·

Measure the compression pressure in as short a time as possible.



If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the glow plug hole, then measure it again.

HINT:
·

If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.

·

If the pressure stays low, a valve may be stuck or seated improperly, or there may be leakage from the gasket.




j.

Remove the compression gauge and SST.


k.

Disconnect the cable from the negative battery terminal.


l.

Connect all connectors to the 4 injectors.


m.

Install the No. 1 engine cover sub-assembly.

(Click hereEngine / Hybrid System>N04C-VL (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION)


n.

Install the 4 bolts to the glow plug hole.

Torque:
22.5 N*m (229 kgf*cm, 17 ft.*lbf)