22100
1.INSTALL INJECTION OR SUPPLY PUMP ASSEMBLY
2.INSTALL COMMON RAIL ASSEMBLY FUEL PIPE SUPPORT
Install the common rail assembly fuel pipe support with the 2 bolts.
55 N*m (561 kgf*cm, 41 ft.*lbf)
82702E
3.INSTALL WIRING HARNESS BRACKET SUB-ASSEMBLY
Install the wiring harness bracket sub-assembly with the 2 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
23849G
4.INSTALL FUEL PIPE SUPPORT
Install the fuel pipe support with the 2 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
23810A
5.INSTALL COMMON RAIL ASSEMBLY
6.INSTALL NO. 3 NOZZLE LEAKAGE PIPE SUB-ASSEMBLY
Install the No. 3 nozzle leakage pipe sub-assembly with 2 new gaskets and the 2 union bolts.
13 N*m (133 kgf*cm, 10 ft.*lbf)
Install the fuel pipe clamp with the nut. Tighten the nut until the clamp edges make contact.
16206A
7.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Install 3 new O-rings and install the No. 2 water by-pass pipe sub-assembly with the 5 bolts.
12204
8.INSTALL VENTILATION VALVE SUB-ASSEMBLY
Install the ventilation valve sub-assembly with the bolt.
Connect the hose and slide the clamp to secure the hose.
29300
9.INSTALL VACUUM PUMP ASSEMBLY
29601B
10.INSTALL VACUUM PUMP OIL PIPE SUB-ASSEMBLY
19971E
11.INSTALL VACUUM PIPE
Install the vacuum pipe with 2 new gaskets and the union bolt.
Install the 2 pipe clamps with the 2 nuts. Tighten the 2 nuts until the clamp edges make contact with the engine side clamp edges.
23803H
12.INSTALL FUEL RETURN PIPE SUB-ASSEMBLY
23811
13.INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE
16100
14.INSTALL ENGINE WATER PUMP ASSEMBLY
16206
15.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
Install 3 new O-rings, 2 new gaskets and the water by-pass pipe sub-assembly with the 8 bolts.
16206B
16.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY
Connect the water hose and slide the clamp to secure the hose.
Install the No. 3 water by-pass pipe sub-assembly with the 2 bolts.
Connect the 2 connectors.
87208L
17.INSTALL WATER PIPE SUB-ASSEMBLY
Install a new O-ring and the water pipe sub-assembly with the 3 bolts.
16333
18.INSTALL WATER OUTLET HOUSING
Install a new gasket and the water outlet housing with the 3 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
16331A
19.INSTALL THERMOSTAT
16331
20.INSTALL WATER OUTLET
Install the water outlet with the 3 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
88431
21.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)
Install the No. 1 compressor mounting bracket and compressor mounting bracket set with the 7 bolts.
55 N*m (561 kgf*cm, 41 ft.*lbf)
29 N*m (291 kgf*cm, 21 ft.*lbf)
Firmly press and hold, the No. 1 compressor mounting bracket and compressor mounting bracket set against the timing gear cover to eliminate any gaps. Then uniformly tighten the 7 bolts.
88444
22.INSTALL IDLE PULLEY ASSEMBLY WITH BRACKET (w/ Air Conditioning System)
Install the idle pulley assembly with bracket with the 3 bolts.
55 N*m (561 kgf*cm, 41 ft.*lbf)
16630G
23.INSTALL IDLER PULLEY ASSEMBLY
Install the idler pulley assembly with the 2 bolts.
55 N*m (561 kgf*cm, 41 ft.*lbf)
24.INSTALL CAMSHAFT POSITION SENSOR
25.INSTALL CRANKSHAFT POSITION SENSOR
89422
26.INSTALL ENGINE COOLANT TEMPERATURE SENSOR
15710
27.INSTALL OIL COOLER ASSEMBLY
83530
28.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY
17141
29.INSTALL EXHAUST MANIFOLD
17111
30.INSTALL INTAKE MANIFOLD
23670
31.INSTALL INJECTOR ASSEMBLY
23741B
32.INSTALL INJECTION PIPE CLAMP
17138A
33.INSTALL INTAKE PIPE STAY
Apply a continuous bead of seal packing (width: 1.5 to 2.5 mm (0.0591 to 0.0984 in.)) as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
| *1 | Seal Packing |
Remove any oil from the contact surface.
Install the intake pipe within 3 minutes, and tighten the bolts within 15 minutes of applying the seal packing.
Install the intake pipe with the 4 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
34.INSTALL INTAKE PIPE WITH VENTURI ASSEMBLY
15301
35.INSTALL OIL DIPSTICK GUIDE
Install the oil dipstick guide with a new O-ring with the bolt.
29 N*m (291 kgf*cm, 21 ft.*lbf)
25625
36.INSTALL EGR VALVE BRACKET
Install the EGR valve bracket with the 4 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
11202D
37.INSTALL NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY
Install 4 new No. 2 cylinder head cover gaskets to the 4 injector assemblies.
| *a | Connector Insertion Side of Injector Assembly |
|
Engine Oil |
To make inserting the part into the injector assembly easier, align the part with the head shape of the injector assembly.
The No. 2 cylinder head cover sub-assembly can be installed in any direction.
Apply a light coat of the engine oil to the 4 No. 2 cylinder head cover gaskets as shown in the illustration.
Install a new cylinder head cover gasket to the No. 2 cylinder head cover sub-assembly.
Install the 2 cylinder head cover spacers and 2 cylinder head cushion to the No. 2 cylinder head cover sub-assembly.
Install the No. 2 cylinder head cover sub-assembly with the 2 bolts.
Connect the PCV hose and install the oil separator assembly with the 6 bolts.
Connect the 4 connectors and install the wire harness with the bolt.
12601B
38.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
Install the No. 1 engine cover sub-assembly and 2 cylinder head cover stays with the 2 bolts.
12180E
39.INSTALL OIL FILLER CAP ASSEMBLY
Install the oil filler cap sub-assembly.
40.INSTALL ENGINE ASSEMBLY
Support the engine with an engine lifter.
Install the engine assembly.
Install the front No. 1 engine mounting bracket LH with the 4 bolts.
|
Bolt |
|
Nut |
Install the engine mounting stabilizer and engine mounting insulator with the 2 nuts.
87 N*m (887 kgf*cm, 64 ft.*lbf)
90 N*m (918 kgf*cm, 66 ft.*lbf)
Install the front No. 1 engine mounting bracket RH with the 4 bolts.
|
Bolt |
|
Nut |
Install the engine mounting stabilizer and engine mounting insulator with the 2 nuts.
87 N*m (887 kgf*cm, 64 ft.*lbf)
90 N*m (918 kgf*cm, 66 ft.*lbf)
82121
41.INSTALL ENGINE WIRE
Install the engine wire.
51202D
42.INSTALL FRONT LOWER SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Install the front lower suspension crossmember sub-assembly with the 6 bolts, 4 washers and 4 nuts.
160 N*m (1631 kgf*cm, 118 ft.*lbf)
45450
43.INSTALL STEERING RELAY ROD ASSEMBLY
| *a | for Center Arm Bracket Assembly Side |
| *b | for Idler Arm Bracket Assembly Side |
Connect the steering relay rod assembly to the center arm bracket assembly and idler arm bracket assembly with the 2 nuts.
Install 2 new cotter pins.
Connect the steering relay rod assembly to the tie rod assembly LH with the nut.
Install a new cotter pin.
87245B
44.CONNECT INLET HEATER WATER HOSE B
Connect the inlet heater water hose B and slide the clamp to secure the hose.
87246B
45.CONNECT OUTLET HEATER WATER HOSE B
Connect the outlet heater water hose B and slide the clamp to secure the hose.
28100
46.INSTALL STARTER ASSEMBLY
47.CONNECT NO. 1 FUEL HOSE RETURN TUBE
22100A
48.CONNECT INJECTION PUMP TO FUEL FILTER FUEL HOSE OR PIPE
44774
49.CONNECT UNION TO CONNECTOR TUBE HOSE
Connect the union to connector tube hose.
17342P
50.INSTALL NO. 2 AIR HOSE
44310
51.INSTALL VANE PUMP ASSEMBLY
Coat a new O-ring with power steering fluid and install it onto the vane pump assembly.
Install the vane pump assembly with the 2 bolts.
20 N*m (204 kgf*cm, 15 ft.*lbf)
53712C
52.INSTALL FRONT FENDER APRON LH
Install the front fender apron LH with the 6 bolts.
7.0 N*m (71 kgf*cm, 62 in.*lbf)
44360
53.INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY
Install the vane pump oil reservoir assembly with the 3 bolts.
18 N*m (184 kgf*cm, 13 ft.*lbf)
27020
54.INSTALL GENERATOR ASSEMBLY
88320
55.INSTALL COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
Install the cooler compressor assembly with the 6 bolts.
47 N*m (475 kgf*cm, 34 ft.*lbf)
Connect the connector.
16577C
56.INSTALL RADIATOR PIPE
Install a new gasket and the radiator pipe with the 2 bolts.
17201
57.INSTALL TURBOCHARGER SUB-ASSEMBLY
31250
58.INSTALL CLUTCH DISC ASSEMBLY
33110
59.INSTALL MANUAL TRANSMISSION ASSEMBLY
16400
60.INSTALL RADIATOR ASSEMBLY