Home › Engine / Hybrid System › N04C-UH (FUEL) › FUEL INJECTOR › 2019.08–2021.01
RM2850E _51 Engine / Hybrid System _073175 N04C-UH FUEL _0356078 FUEL INJECTOR A

N04C-UH FUEL  FUEL INJECTOR  INSTALLATION  


PROCEDURE

Hide 23670 1.INSTALL INJECTOR ASSEMBLY

A288762E05
2.344,1.688 2.552,0.76 true 2.24,1.708 2.5,1.969 0.26,0.26 10 false *1

Text in Illustration
*1 Injector Compensation Code

NOTICE:

Register the injector compensation code of a new fuel injector in the ECM when replacing the fuel injector. Register the injector compensation code in advance so that it can be installed in the correct position.


a.

Install 4 new injection nozzle seats to the cylinder head.


b.

Apply a light amount of clean engine oil to 4 new O-rings.


c.
A289254E03
1.208,0.865 1.406,1.208 false 1.073,0.688 1.385,0.885 0.313,0.198 10 false *1

Install an O-ring to each injector as shown in the illustration.

Text in Illustration
*1 O-ring


d.

Install a new No. 2 cylinder head cover gasket to each injector.


e.

Insert the 4 injectors into the cylinder head.

NOTICE:
·

Check that the insertion part of the fuel injector has no foreign matter attached.

·

When reusing a fuel injector, install the same fuel injector that was removed. Otherwise, it could cause the engine to malfunction.

·

Carefully insert the fuel injector so that the O-ring is not caught between the cylinder head and the injector.




f.
A146734

Temporarily install the 4 nozzle holder clamps with the 4 clamp bolts.

NOTICE:

Be sure to install the holder clamps and bolts in their original positions.



g.
A146733

Install the 4 holder seals.

NOTICE:

Securely insert the tip of the holder seal into the fuel injector.



h.
A146735

Temporarily install the nozzle leakage pipe assembly through 5 new gaskets by hand with the union bolt and 4 hollow screws.

NOTICE:

Make sure that the hollow screws and nozzle leakage pipe assembly are not deformed or damaged.



i.
A146738

Temporarily tighten the union nuts of injection pipe sub-assemblies No. 1, No. 2, No. 3 and No. 4 by hand.

NOTICE:

If an injector has been replaced, the corresponding injection pipe sub-assembly must also be replaced.



j.
A146734

Tighten the 4 nozzle holder clamp bolts.

Torque:

25 N*m (255 kgf*cm, 18 ft.*lbf)


NOTICE:

After tightening the nozzle holder clamp bolts, check that the fuel injector and the nozzle holder clamp do not interfere with the valve spring.



k.
A146732

Tighten the 4 hollow screws and union bolt.

Torque:

13 N*m (130 kgf*cm, 10 ft.*lbf)


NOTICE:

If the nozzle leakage pipe assembly has been tightened to more than the specified torque, replace it with a new one.



l.
A146738

Using a union nut wrench (17 mm), tighten the injection pipe union nuts.

Torque:

35 N*m (357 kgf*cm, 26 ft.*lbf)


NOTICE:

Refer to the torque above when not using the union nut wrench. When using the union nut wrench, calculate the torque in accordance with the lengths of the union nut wrench and torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Hide 23741B 2.INSTALL INJECTION PIPE CLAMP

a.

Install the 2 injection pipe clamps with the 2 nuts.

Tighten the 2 nuts until the clamp's edges make contact with the engine side clamp's edges.


Hide 11201 3.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.

Install a new cylinder head cover gasket onto the cylinder head cover.


b.

Install the cylinder head cover and the 2 cushions with the 2 bolts.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



c.

Install the cylinder head cover cushion rubber.


d.

Install the wire harness and connect the 5 connectors.


Hide 11202D 4.INSTALL NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY

a.

Install the No. 2 cylinder head cover and the 2 stays with the 2 bolts.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



Hide 12180E 5.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.

Install the oil filler cap.


Hide 25608 6.INSTALL EGR COOLER SUB-ASSEMBLY

Hide 17271 7.INSTALL NO. 1 TURBO INSULATOR

Hide 16206C 9.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 58701A 11.INSTALL FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY (for LHD)

Hide 58701A 12.INSTALL FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY (for RHD)

Hide 33504F 13.INSTALL SHIFT LEVER SUB-ASSEMBLY (for Manual Transmission)

Hide 58841A 14.INSTALL SHIFTING HOLE COVER (for Automatic Transmission)

Hide 33503F 15.INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY (for Automatic Transmission)

Hide 33820B 16.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for RHD)

Hide 33820B 17.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for LHD)

Hide 58848A 18.INSTALL SHIFT LEVER HOLE COVER WITH BOOTS (for RHD)

Hide 33531B 19.INSTALL SHIFT AND SELECT LEVER SHAFT DUST BOOT (for LHD)

Hide 58534A 20.INSTALL TRANSMISSION COVER MAT (for Manual Transmission)

Hide 58420 21.INSTALL NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY (for Automatic Transmission)

Hide 33820B 22.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transmission)

Hide 33820B 23.ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transmission)

Hide 24. SHIFT LEVER POSITION (for Automatic Transmission)

Hide 58420 25.INSTALL NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

Hide 26.BLEED AIR FROM FUEL SYSTEM

Hide 27.REGISTRATION INJECTOR COMPENSATION CODE

a.

Register the injector compensation code.

Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION


Hide 28.CHECK FOR INJECTOR COMPENSATION CODE

Hide 31.INSPECT FOR OIL LEAK

Hide 58521D 32.INSTALL ENGINE SERVICE HOLE COVER MAT (w/o Carpet)

Hide 58734B 33.INSTALL ENGINE SERVICE COVER REAR WEATHERSTRIP

Hide 58410 34.INSTALL ENGINE SERVICE HOLE COVER

Hide 58521D 35.INSTALL ENGINE SERVICE HOLE COVER MAT (w/ Carpet)