Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P073D  Unable to Engage Neutral  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P073D Unable to Engage Neutral Diagnosis Condition:
·

Battery voltage is in the range of 10 V to 16 V


Malfunction Status:
·

Detected at one of the following conditions

-

The condition that there is an abnormality (communication blackout between the translate ECU assmbly and transmission ECU) in the lock up information provided by the translate ECU assmbly remains for 5 seconds or more.

-

The condition that the neutral switch is positioned at the neutral position even though the neutral information provided by the translate ECU assmbly recognizes the "non-neutral" state remains for 10 seconds or more.

-

The condition that the neutral information provided by the translate ECU assmbly recognizes the "neutral" state even though the lock up information recognizes the "lock up" remains for 10 seconds or more.



Malfunction Duration:

10 seconds or more


·

Neutral switch

·

Harness or connector

·

CAN communication

·

ECM


Class B1 DTC stored

MONITOR DESCRIPTION

Transmission information is transferred through CAN communication.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P073D (Click here)

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS to ON.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.


Result:
Result Proceed to
DTC P073D is output A
DTCs other than P073D are output B



A

2.READ VALUE USING GTS (NEUTRAL POSITION SWITCH)

B

2.READ VALUE USING GTS (NEUTRAL POSITION SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Neutral Position Switch.


e.

Read the value displayed on the GTS.


Standard:
Item Condition Reference Value
Neutral Position Switch Shift lever in N range ON
Shift lever in other range OFF


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SHORT IN WIRE HARNESS)

NG

7.CHECK AUTOMATIC TRANSMISSION SYSTEM
3.CHECK HARNESS AND CONNECTOR (SHORT IN WIRE HARNESS)
a.
A405886C16
1.479,0.125 1.896,0.396 0.417,0.271 0.177,0.167 0.49,0.365 0.313,0.198 10 false *a 1.635,0.188 1.948,0.385 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM and ECM vehicle side harness.


c.

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Condition Specified Condition
V-11 - Body ground and other terminals Ignition switch ON Shift lever in N range : 10 V or higher
Shift lever in other range : 0V


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

6.INSPECT NEUTRAL SWITCH CIRCUIT
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

6.INSPECT NEUTRAL SWITCH CIRCUIT
a.

Inspect the neutral switch circuit.


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
7.CHECK AUTOMATIC TRANSMISSION SYSTEM
a.

Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT