Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM C

N04C-VJ ENGINE CONTROL  ECD SYSTEM  P0088  Fuel Rail / System Pressure - Too High  P0627  Fuel Pump Control Circuit / Open  P1229  Fuel Pump System  


DESCRIPTION

The injection or supply pump assembly is a single-type pump and has a circuit for fuel suction that achieves high pressure force feed and reduction of driving torque, and for force feed process. The ECM controls the suction control valve, which operates fuel suction by the plunger in the process of suction.

When the internal fuel pressure of the common rail assembly exceeds the target pressure, the pressure limiter on the common rail assembly starts operating to control the internal fuel pressure of the common rail assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0088 Fuel Rail / System Pressure - Too High Conditions (a) and (b) are met 60 seconds or more:
(1 trip detection logic)

(a) Ignition switch ON

(b) Internal fuel pressure of the common rail: 250 MPa (2549.3 kg/cm2, 36250 psi) or more


·

Harness and connector

·

Injection or supply pump assembly (suction control valve)

·

Common rail assembly

·

ECM


Comes on DTC stored
P0627 Fuel Pump Control Circuit / Open Open or short in suction control valve circuit for more than 0.5 seconds
(1 trip detection logic)
·

Harness and connector

·

Injection or supply pump assembly (suction control valve)

·

Common rail assembly

·

ECM


Comes on DTC stored
P1229 Fuel Pump System Conditions (a) and (b) are met 60 seconds or more:
(1 trip detection logic)

After the engine starts

The actual fuel pressure is 300 MPa (3059.19 kg/cm2, 43500 psi) or more than the target fuel pressure


·

Harness and connector

·

Injection or supply pump assembly (suction control valve)

·

Common rail assembly

·

ECM

·

Input signal to injection or supply pump assembly (suction control valve)


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0088
P1229
After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds
P0627 Idle the engine for 1 seconds or more.

WIRING DIAGRAM

A261580E03
0.667,2.135 0.979,2.292 0.313,0.156 10 false B52 0.656,2.302 2.615,2.458 1.958,0.156 10 false Suction Control Valve 1.5,3.427 1.969,3.615 0.469,0.188 10 false VC2 1.521,6.208 1.948,6.385 0.427,0.177 10 false VC1 1.417,3.979 1.833,4.167 0.417,0.188 10 false PCR2 1.417,5.656 1.938,5.833 0.521,0.177 10 false PCR1 1.594,4.531 1.906,4.74 0.313,0.208 10 false E2 1.594,5.115 1.99,5.271 0.396,0.156 10 false E1 5.74,3.396 6.281,3.615 0.542,0.219 10 false VC2 5.75,6.229 6.094,6.469 0.344,0.24 10 false VC 5.74,6.792 6.052,6.979 0.313,0.188 10 false E01 5.74,3.969 6.229,4.167 0.49,0.198 10 false PCR2 5.75,1.646 6.479,1.906 0.729,0.26 10 false PCV- 5.74,1 6.271,1.229 0.531,0.229 10 false PCV+ 5.74,5.656 6.198,5.854 0.458,0.198 10 false PCR1 5.74,4.531 6.094,4.698 0.354,0.167 10 false E21 5.75,5.083 6.01,5.26 0.26,0.177 10 false E2 1.927,3.292 2.083,3.448 0.156,0.156 10 false 6 1.927,6.083 2.083,6.24 0.156,0.156 10 false 1 1.938,3.854 2.094,4.01 0.156,0.156 10 false 5 1.927,5.542 2.083,5.698 0.156,0.156 10 false 2 1.885,0.885 2.042,1.042 0.156,0.156 10 false 1 1.927,4.406 2.083,4.563 0.156,0.156 10 false 4 1.927,4.99 2.083,5.146 0.156,0.156 10 false 3 5.302,3.417 5.74,3.625 0.438,0.208 10 false B105 5.302,1.01 5.74,1.208 0.438,0.198 10 false B103 5.302,3.979 5.75,4.198 0.448,0.219 10 false B105 5.302,4.531 5.729,4.708 0.427,0.177 10 false B105 5.302,5.094 5.76,5.292 0.458,0.198 10 false B104 5.292,5.656 5.688,5.854 0.396,0.198 10 false B105 5.302,6.208 5.729,6.396 0.427,0.188 10 false B104 5.313,6.813 5.74,6.979 0.427,0.167 10 false B102 5.906,7.354 6.396,7.625 0.49,0.271 10 false ECM 0.438,6.677 0.729,6.833 0.292,0.156 10 false B93 0.417,6.833 3.75,7.125 3.333,0.292 10 false Common Rail Assembly (Fuel Pressure Sensor) 5.365,3.219 5.646,3.417 0.281,0.198 10 false 13 5.365,6.021 5.646,6.208 0.281,0.188 10 false 13 5.365,5.469 5.646,5.625 0.281,0.156 10 false 16 5.365,4.896 5.708,5.063 0.344,0.167 10 false 14 5.375,4.344 5.667,4.51 0.292,0.167 10 false 14 5.417,3.792 5.667,4.01 0.25,0.219 10 false 2 5.375,1.469 5.552,1.625 0.177,0.156 10 false 12 5.385,0.802 5.563,0.958 0.177,0.156 10 false 23 5.375,6.615 5.594,6.823 0.219,0.208 10 false 11 1.885,1.521 2.042,1.677 0.156,0.156 10 false 2 1.427,1 1.844,1.188 0.417,0.188 10 false SCV+ 1.417,1.656 1.833,1.844 0.417,0.188 10 false SCV- 5.292,1.656 5.729,1.854 0.438,0.198 10 false B103

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injection or supply pump assembly, the ECM needs initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read DTCs.


Result:
Result Proceed to
DTC P0180, P0182, P0183, P0190, P0191, P0192, P0193 or P0200, P0201, P0202, P0203, P0204, P062D is not output A
DTC P0180, P0182, P0183, P0190, P0191, P0192, P0193 or P0200, P0201, P0202, P0203, P0204, P062D is output B



A

2.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

B

2.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.

Inspect the suction control valve.

Click hereEngine / Hybrid System>N04C-VJ (FUEL)>FUEL SUPPLY PUMP>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read DTCs.


Result:
Result Proceed to
DTC P0088 and/or P1229 A
DTC P0627 B



A

4.READ VALUE USING GTS (TARGET PUMP SCV CURRENT)

B

8.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
4.READ VALUE USING GTS (TARGET PUMP SCV CURRENT)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Target Pump SCV Current.


e.

Read the value.

Standard:
Engine Speed Result
Idling 1350 to 2200 mA



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (FUEL PRESS)

NG

12.CHECK FUEL INJECTION SYSTEM
5.READ VALUE USING GTS (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press, Target Common Rail Pressure.


e.

Check that the internal fuel pressure of the common rail is within the specification below.

Standard:
Item Engine Speed Specified Condition
Fuel Press Idling Approximately 20000 to 30000 kPa
2800rpm Approximately 110000 to 120000 kPa
Target Common Rail Pressure Idling Difference from target common rail pressure within 5000 kPa
2800rpm Difference from target common rail pressure within 5000 kPa


NOTICE:

The fuel pressure is listed here as a standard value, but the standard value will vary depending on the vehicle condition and model.

When judging the fuel pressure, check that the common rail target fuel pressure and fuel pressure follow reliably with the accelerator position and engine speed at a constant setting.

However, the common rail target fuel pressure and fuel pressure will not follow immediately after operating the accelerator pedal.



Result:
Result Proceed to
NG A
OK B



A

6.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

B

8.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
6.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Check the wire harness and connector.

i.

Disconnect the fuel pressure sensor connector.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Standard Resistance Condition Specified Condition
B104-13(VC) - B93-1(VC1) Always Below 1 Ω
B105-16(PCR1) - B93-2(PCR1) Always Below 1 Ω
B104-14(E2) - B93-3(E1) Always Below 1 Ω
B105-14(E21) - B93-4(E2) Always Below 1 Ω
B105-2(PCR2) - B93-5(PCR2) Always Below 1 Ω
B105-13(VC2) - B93-6(VC2) Always Below 1 Ω
B104-13(VC) or B93-1(VC1) - Body ground Always 10 kΩ or higher
B105-16(PCR1) or B93-2(PCR1) - Body ground Always 10 kΩ or higher
B104-14(E2) or B93-3(E1) - Body ground Always 10 kΩ or higher
B105-14(E21) or B93-4(E2) - Body ground Always 10 kΩ or higher
B105-2(PCR2) or B93-5(PCR2) - Body ground Always 10 kΩ or higher
B105-13(VC2) or B93-6(VC2) Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (FUEL PRESS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.READ VALUE USING GTS (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.


e.

Wiggle the fuel pressure sensor connector and check that the fuel pressure reading does not change.

OK:

The fuel pressure reading does not change.



Result:
Proceed to
OK
NG



OK

12.CHECK FUEL INJECTION SYSTEM

NG

REPLACE FUEL PRESSURE SENSOR

8.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Check the wire harness and connector.

i.

Disconnect the suction control valve connector.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Standard Resistance Condition Specified Condition
B103-23 (PCV+) - B52-1 (SCV+) Always Below 1 Ω
B103-12 (PCV-) - B52-2 (SCV-) Always Below 1 Ω
B103-23 (PCV+) or B52-1 (SCV+) - Body ground Always 10 kΩ or higher
B103-12 (PCV-) or B52-2 (SCV-) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

9.INSPECT ECM (PCV+ AND PCV- OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT ECM (PCV+ AND PCV- OUTPUT VOLTAGE)
a.
A256048C06
2.823,0.156 3.313,0.448 0.49,0.292 2.271,0.156 2.76,0.448 0.49,0.292 3.219,0.969 2.979,1.542 true 2.74,0.969 2.271,1.542 true 2.729,0.844 1.615,1.51 true 2.917,0.229 3.271,0.396 0.354,0.167 10 false B102 2.365,0.229 2.781,0.417 0.417,0.188 10 false B103 2,1.594 2.604,1.76 0.604,0.167 10 false 23(PCV+) 1.26,1.583 1.875,1.76 0.615,0.177 10 false 12(PCV-) 2.75,1.594 3.271,1.76 0.521,0.167 10 false 11(E01) 2.771,3.583 3.365,3.823 0.594,0.24 10 false 5 V/DIV. 2.802,3.917 3.396,4.135 0.594,0.219 10 false 1 V/DIV. 0.167,3.604 0.635,3.781 0.469,0.177 10 false PCV+ 0.167,3.969 0.583,4.188 0.417,0.219 10 false PCV- 0.125,0.094 0.302,0.25 0.177,0.156 10 false *a 1.281,4.333 3.115,4.531 1.833,0.198 10 false 5 msec./DIV.
*a Component with harness connected
(ECM)


While cranking or idling the engine, check the waveform of the ECM connector using an oscilloscope.

OK:
Tester Connection Condition Tool Setting Specified Condition
B103-23 (PCV+) - B102-11 (E01) Idling or cranking with warm engine 5 V/DIV., 5 msec./DIV. Correct waveform appears as shown
B103-1 (PCV-) - B102-11 (E01) Idling or cranking with warm engine 1 V/DIV., 5 msec./DIV. Correct waveform appears as shown



Result:
Proceed to
OK
NG



OK

10.CLEAR DTC

NG

10.CLEAR DTC
a.

Connect the GTS to the DLC3.



Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS
11.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.


f.

Read the DTCs.


Result:
Result Proceed to
P0088, P0627 or P1229 is output A
P0088, P0627 or P1229 is not output B



A

12.CHECK FUEL INJECTION SYSTEM

B

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

12.CHECK FUEL INJECTION SYSTEM

Result:
Proceed to
OK
NG



OK

NG

END