Home › Drivetrain › A861E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2021.01
RM2850E _52 Drivetrain _082622 A861E AUTOMATIC TRANSMISSION / TRANSAXLE _0398655 AUTOMATIC TRANSMISSION SYSTEM C

A861E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  U0100  Lost Communication With ECM/PCM "A"  


DESCRIPTION

The ECM communicates with the transmission control ECU assembly via the Controller Area Network (CAN).

If there is a problem in communication, the transmission control ECU assembly stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
U0100 Lost Communication With ECM/PCM "A" 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

Battery voltage 10 V or higher and 1 second or more elapses since recovering from low voltage status

2.

Lost communication between ECM and transmission control ECU assembly

3.

2 seconds or more

4.

1 trip detection logic


·

Wire harness or connector

·

ECM

·

Transmission control ECU assembly

·

CAN communication system


O/D OFF Indicator Light: Blinking DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


1.

Turn the ignition switch to ON.


WIRING DIAGRAM

C454815E01
0.063,0.073 2.271,0.313 2.208,0.24 12 false for N04C-WA: 0.823,2.469 3.167,2.646 2.344,0.177 10 false from ENG STOP/ P LOCK NO. 2 Reray 1.99,1.875 3.365,2.073 1.375,0.198 10 false IGN NO. 1 2,1.063 3.375,1.26 1.375,0.198 10 false EFI NO. 2 4.708,0.906 5.052,1.094 0.344,0.188 10 false V-1 5.094,0.906 5.438,1.094 0.344,0.188 10 false A115 4.667,1.729 5.01,1.917 0.344,0.188 10 false V-13 5.083,1.719 5.427,1.906 0.344,0.188 10 false A115 4.667,2.198 5.01,2.385 0.344,0.188 10 false V-33 5.094,2.198 5.438,2.385 0.344,0.188 10 false A115 5.083,3.135 5.427,3.323 0.344,0.188 10 false A115 5.094,3.677 5.438,3.865 0.344,0.188 10 false A115 5.083,4.49 5.427,4.677 0.344,0.188 10 false A115 5.083,4.969 5.427,5.156 0.344,0.188 10 false A115 5.083,5.438 5.427,5.625 0.344,0.188 10 false A115 4.667,3.135 5.01,3.323 0.344,0.188 10 false V-36 4.667,3.677 5.01,3.865 0.344,0.188 10 false V-16 4.667,4.49 5.01,4.677 0.344,0.188 10 false V-40 4.656,4.958 5,5.146 0.344,0.188 10 false V-60 4.656,5.448 5,5.635 0.344,0.188 10 false V-39 5.771,6.438 6.115,6.625 0.344,0.188 10 false ECM 5.167,0.688 5.531,0.875 0.365,0.188 10 false 49 5.208,1.49 5.563,1.688 0.354,0.198 10 false 6 5.208,1.979 5.552,2.167 0.344,0.188 10 false 5 5.167,2.917 5.51,3.104 0.344,0.188 10 false 48 5.177,3.448 5.521,3.635 0.344,0.188 10 false 59 5.156,4.271 5.5,4.458 0.344,0.188 10 false 12 5.167,4.75 5.51,4.938 0.344,0.188 10 false 36 5.177,5.229 5.521,5.417 0.344,0.188 10 false 60 5.5,0.896 5.844,1.083 0.344,0.188 10 false +B 5.5,1.708 6.063,1.917 0.563,0.208 10 false IGSW 5.5,2.208 6.063,2.417 0.563,0.208 10 false IG 5.49,3.125 6.052,3.333 0.563,0.208 10 false CANH 1.354,3.135 1.917,3.344 0.563,0.208 10 false CAN+ 1.823,2.927 2.167,3.115 0.344,0.188 10 false 20 1.354,3.677 1.917,3.885 0.563,0.208 10 false CAN- 1.823,3.479 2.167,3.667 0.344,0.188 10 false 21 5.49,3.656 6.052,3.865 0.563,0.208 10 false CANL 5.479,4.479 6.042,4.688 0.563,0.208 10 false E01 5.479,4.958 6.042,5.167 0.563,0.208 10 false E02 5.479,5.427 6.042,5.635 0.563,0.208 10 false E11 0.688,6 4.354,6.198 3.667,0.198 10 false : CAN Communication Line 0.677,4.115 1.24,4.323 0.563,0.208 10 false B133 0.677,4.281 1.99,4.677 1.313,0.396 10 false Transmission Control ECU Assembly 3.521,2.396 3.677,2.594 0.156,0.198 10 false * 0.167,6.49 1.958,6.719 1.792,0.229 10 false *: w/ Enjine Stop System

C373195E03
2.042,0.833 3.333,1.063 1.292,0.229 10 false EFI NO.2 2.031,1.385 3.625,1.552 1.594,0.167 10 false IGN NO.1 2.323,2.146 2.719,2.323 0.396,0.177 10 false CAN+ 2.313,2.677 2.708,2.854 0.396,0.177 10 false CAN- 5.5,0.667 5.781,0.844 0.281,0.177 10 false +B 5.521,1.208 5.917,1.385 0.396,0.177 10 false IGSW 5.5,2.135 5.896,2.313 0.396,0.177 10 false CANP 5.5,2.698 5.896,2.875 0.396,0.177 10 false CANN 5.521,3.406 5.917,3.583 0.396,0.177 10 false E1 5.135,0.677 5.438,0.865 0.302,0.188 10 false A57 5.115,1.208 5.417,1.396 0.302,0.188 10 false A56 5.125,2.156 5.427,2.344 0.302,0.188 10 false A56 5.125,2.688 5.427,2.875 0.302,0.188 10 false A56 5.094,3.406 5.448,3.604 0.354,0.198 10 false B102 2.781,1.958 3.031,2.115 0.25,0.156 10 false 20 2.781,2.49 3.031,2.646 0.25,0.156 10 false 21 5.156,0.469 5.406,0.625 0.25,0.156 10 false 24 5.177,1.01 5.427,1.167 0.25,0.156 10 false 24 5.188,1.927 5.438,2.083 0.25,0.156 10 false 8 5.188,2.479 5.438,2.635 0.25,0.156 10 false 2 5.208,3.198 5.458,3.354 0.25,0.156 10 false 1 1.604,3.115 2.208,3.281 0.604,0.167 10 false B133 1.594,3.271 3.313,3.656 1.719,0.385 10 false Transmission Control ECU Assembly 5.74,4 6.563,4.26 0.823,0.26 10 false ECM 0.531,4.24 2.917,4.469 2.385,0.229 10 false : CAN Communication Line 0.063,0.063 1.323,0.344 1.26,0.281 12 false for N04C-VJ:

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Perform initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION



PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
for N04C-WA A
for N04C-VJ B



A

2.INSPECT ECM (POWER SOURCE)

B

4.CHECK ECM (ECM POWER SOURCE CIRCUIT)
2.INSPECT ECM (POWER SOURCE)
a.

Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM and ECM vehicle side harness.


c.

Turn the ignition switch to ON.


d.
A405886C03
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


Measure the voltage according to the value(s) in the table below.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM

Standard Voltage:
Tester Connection Condition Specified Condition
V-1 - Body ground Ignition switch ON 11 to 14 V
V-13 - Body ground Ignition switch ON 11 to 14 V
V-33 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


c.
A405886C03
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM

Standard Resistance:
Tester Connection Condition Specified Condition
V-40 - Body ground Always Below 1 Ω
V-60 - Body ground Always Below 1 Ω
V-39 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ECM (ECM POWER SOURCE CIRCUIT)
a.
A360756C17
0.198,0.208 0.573,0.448 0.375,0.24 0.698,0.208 1.073,0.448 0.375,0.24 0.146,1.583 0.198,1.073 true 1.021,1.594 0.677,0.938 true 0.271,0.26 0.573,0.438 0.302,0.177 10 false A57 0.781,0.25 1.083,0.427 0.302,0.177 10 false A56 0.063,0.042 0.25,0.24 0.188,0.198 10 false *a 0.073,1.635 0.552,1.823 0.479,0.188 10 false 24(+B) 0.792,1.625 1.417,1.813 0.625,0.188 10 false 24(IGSW)
*a Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A57-24(+B) - Body ground Ignition switch ON 11 to 14 V
A56-24 (IGSW)- Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.
C373148C02
2.615,1.208 3.052,1.458 0.438,0.25 2.792,2.906 3.156,1.875 true 2.688,1.271 3.083,1.448 0.396,0.177 10 false B102 2.594,2.958 2.99,3.125 0.396,0.167 10 false 1(E1) 0.125,0.094 0.521,0.26 0.396,0.167 10 false *a
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B102-1 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ECM - TRANSMISSION CONTROL ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ECM - TRANSMISSION CONTROL ECU ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the transmission control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A56-8 (CANP) - B133-20 (CAN+) Always Below 1 Ω
A56-2 (CANN) - B133-21 (CAN-) Always Below 1 Ω
A56-8 (CANP) or B133-20 (CAN+) - Body ground Always 10 kΩ or higher
A56-2 (CANN) or B133-21 (CAN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE TRANSMISSION CONTROL ECU ASSEMBLY
a.

Replace the transmission control ECU assembly.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
8.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Trouble Codes.


e.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTC U0100 is not output A
DTC U0100 is output B



A

END

B