The accelerator position sensor, which is installed to the accelerator pedal, detects the accelerator pedal position. When the ECM detects a malfunction in the accelerator position sensor, it sends a malfunction detection signal to the transmission control ECU assembly. A DTC is output when the transmission control ECU assembly receives this signal.
A DTC is output when a malfunction signal is received from the ECM for the engine torque amount requested from the transmission control ECU assembly, or when the signal cannot be received.
During sudden braking or when performing shift control while driving under lock-up, CAN communication is used to send an exhaust brake cut request signal to the ECM. A DTC is output when an exhaust brake operating signal is received while this exhaust brake cut request signal is sent.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Memory |
|---|---|---|---|---|---|
| P1604 | Engine Control System Malfunction | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
DTC Detection Condition 1:
1.
CAN communication is normal 2.
Accelerator position or engine torque ratio malfunction signal received from ECM, or no signal 3.
0.5 seconds or more 4.
1 trip detection logic DTC Detection Condition 2:
1.
CAN communication is normal 2.
Exhaust brake operating signal received during shift operation 3.
0.5 seconds or more 4.
8 trip detection logic |
·
ECD system ·
CAN communication system ·
ECM ·
Transmission control ECU assembly |
O/D OFF Indicator Light: Blinking | DTC stored |
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Start the engine.*1
Turn the exhaust brake switch to ON.*2
Perform the D Position Shift Test inspection in Road Test.*3
Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>ROAD TEST
Turn the ignition switch off.*4
Perform steps (*1) through (*4) 8 times.
Check for DTCs again.
Perform initialization when parts related to the automatic transmission are replaced.
Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION
Check for ECD system DTCs.
for N04C-WA: Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR
for N04C-VJ: Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| ECD system DTCs are not output | A |
| ECD system DTCs are output | B |
If any other codes besides ECD system DTCs are output, perform troubleshooting for those DTCs first.
A
B
for N04C-WA: Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
for N04C-VJ: Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / ECT / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| DTC U0100 is not output | A |
| DTC U0100 is output | B |
If any DTCs other than P1604 are output, perform troubleshooting for those DTCs first.
A
B
Check CAN communication system
Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication system is normally | A |
| CAN communication system is abnormal | B |
A
B
Replace the transmission control ECU assembly.
Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>TCM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / ECT / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P1604 is output | B |
A
B