47264D
1.INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS
Temporarily install the lock nut and brake master cylinder push rod clevis to the brake booster assembly.
Tighten the lock nut when adjusting the brake pedal height.
44610
2.INSTALL BRAKE BOOSTER ASSEMBLY
Install the brake booster assembly to the pedal bracket sub-assembly with the 4 nuts.
13 N*m (133 kgf*cm, 10 ft.*lbf)
Install push rod pin (Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL>INSTALLATION).
55106D
3.INSTALL PEDAL BRACKET SUB-ASSEMBLY
Install the pedal bracket sub-assembly with the 5 bolts and 2 nuts.
19 N*m (194 kgf*cm, 14 ft.*lbf)
8.0 N*m (82 kgf*cm, 71 in.*lbf)
20 N*m (199 kgf*cm, 14 ft.*lbf)
Connect the clamps to the pedal bracket sub-assembly.
4.CONNECT VACUUM HOSE ASSEMBLY
Connect the vacuum hose assembly to the brake booster assembly with the clip.
5.INSTALL BRAKE TUBE
Install a new No. 3 brake tube clamp with the bolt.
7.5 N*m (76 kgf*cm, 66 in.*lbf)
Using a union nut wrench, connect the 2 brake tubes to the tube connector.
24 N*m (245 kgf*cm, 18 ft.*lbf)
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 22 N*m (224 kgf*cm, 16 ft.*lbf)
| *a | Torque Wrench Fulcrum Length |
| *b | Union Nut Wrench |
Connect the 2 brake tubes to the No. 3 brake tube clamp.
Install the 2 new No. 3 brake tube clamps with the 2 bolts.
7.5 N*m (76 kgf*cm, 66 in.*lbf)
Attach the 4 claws and connect the 2 brake tubes to the No. 3 brake tube clamps.
Install a new No. 2 brake tube clamp.
Connect the 2 brake tubes to the No. 2 brake tube clamp.
Install a new No. 1 brake tube clamp.
Connect the 2 brake tubes to the No. 1 brake tube clamp.
31481K
6.INSTALL MASTER CYLINDER TO TUBE CONNECTOR TUBE
Using a union nut wrench, connect the master cylinder to tube connector tube to the tube connector.
24 N*m (245 kgf*cm, 18 ft.*lbf)
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 22 N*m (224 kgf*cm, 16 ft.*lbf)
| *a | Torque Wrench Fulcrum Length |
| *b | Union Nut Wrench |
Attach the claw and connect the master cylinder to tube connector tube to the No. 3 brake tube clamp.
Attach the 2 claws and connect the master cylinder to tube connector tube to the No. 3 brake tube clamps.
Connect the master cylinder to tube connector tube to the No. 2 brake tube clamp.
Connect the clamp to the master cylinder to tube connector tube.
Install the clamp to the pedal bracket sub-assembly with the bolt.
7.5 N*m (76 kgf*cm, 66 in.*lbf)
Connect the master cylinder to tube connector tube (Click hereDrivetrain>CLUTCH>CLUTCH MASTER CYLINDER>INSTALLATION).
7.CONNECT CLUTCH RESERVOIR TUBE
8.CONNECT NO. 1 CLUTCH BOOSTER VACUUM HOSE
47201
9.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY
55305C
10.INSTALL INSTRUMENT PANEL REINFORCEMENT SUB-ASSEMBLY
Install the instrument panel reinforcement sub-assembly with the 4 bolts.
18 N*m (184 kgf*cm, 13 ft.*lbf)
55330B
11.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY
12.INSTALL STEERING COLUMN ASSEMBLY
55301
13.INSTALL INSTRUMENT PANEL SUB-ASSEMBLY