Home › Engine / Hybrid System › N04C-VJ (EXHAUST) › EXHAUST PIPE › from 2021.01
RM2850E _51 Engine / Hybrid System _096895 N04C-VJ EXHAUST _0461981 EXHAUST PIPE A

N04C-VJ EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17410 2.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Install a new gasket.


b.

Temporarily install the front exhaust pipe assembly with a new bolt, 3 spacers and 2 new nuts.


c.

Temporarily install the clamp to the No. 1 exhaust pipe support bracket with a new clamp bolt.


d.

Tighten the bolt and 2 nuts.

Torque:
70 N*m (714 kgf*cm, 52 ft.*lbf)


e.

Tighten the clamp bolt.

Torque:
25.4 N*m (259 kgf*cm, 19 ft.*lbf)


Hide 19971G 4.INSTALL VACUUM PIPE

a.
A396332

Install the vacuum pipe with the 2 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


b.

Connect the 2 vacuum hoses.


Hide 16028 5.CONNECT NO. 2 TURBO WATER PIPE SUB-ASSEMBLY

Hide 17402 7.INSTALL FRONT NO. 2 EXHAUST PIPE SUB-ASSEMBLY

a.

Install the a new gasket to the front exhaust pipe assembly.


b.

Install the front No. 2 exhaust pipe sub-assembly with 3 new bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17420 8.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.
A077857

Using a vernier caliper, measure the free length of the compression spring.

Minimum free length:

38.5 mm (1.52 in.)


If the free length is less than the minimum, replace the compression spring.


b.

Fully push a new gasket onto the front No. 2 exhaust pipe sub-assembly by hand.


c.
A424812C02
0.167,2.229 0.417,2.229 false 2.406,0.917 2.833,0.917 true 1.125,3.156 1.375,2.073 1.375,2.073 1.552,2.073 true 0.969,4.073 1.583,4.406 1.583,4.406 1.844,4.406 true 1.344,1.406 1.521,1.406 1.521,1.406 1.917,1.323 true 1.156,1.313 1.344,1.5 0.188,0.188 10 false *1 1.594,1.99 1.802,2.188 0.208,0.198 10 false *2 1.875,4.323 2.083,4.51 0.208,0.188 10 false *3 0.448,2.125 0.656,2.323 0.208,0.198 10 false *a 2.865,0.823 3.052,1.01 0.188,0.188 10 false *b
*1 Gasket
*2 Front No. 2 Exhaust Pipe Sub-assembly
*3 Center Exhaust Pipe Assembly
*a Gap Between Flanges
*b Wooden Block


Using a wooden block and hammer, gradually tap the gasket until it is flush with the end face of the front No. 2 exhaust pipe sub-assembly.

NOTICE:
·

Make sure to install the gasket in the correct direction.

·

Do not reuse the gasket.

·

Do not drop or otherwise damage the gasket.

·

Do not damage the sliding portion of the gasket.

·

Make sure to push the gasket by hand. Do not push in the gasket as you install the center exhaust pipe assembly.




d.

Install the center exhaust pipe assembly with 4 new nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


e.

Install the center exhaust pipe assembly to the front No. 2 exhaust pipe sub-assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


f.

Install the 4 hose clips to the 2 air hoses.


g.

Install the 2 air hoses to the differential pressure sensor and center exhaust pipe assembly and slide the 4 hose clips to secure it.


Hide 17430 9.INSTALL EXHAUST TAILPIPE ASSEMBLY

a.
A077857

Using a vernier caliper, measure the free length of the compression spring.

Minimum free length:

38.5 mm (1.52 in.)


If the free length is less than the minimum, replace the compression spring.


b.

Fully push a new gasket onto the center exhaust pipe assembly by hand.


c.
A481278C01
0.406,2.177 0.656,2.177 false 2.406,0.917 2.833,0.917 true 1.5,3.042 1.729,2.115 1.729,2.115 1.906,2.115 true 1.385,4.115 2,4.375 2,4.375 2.26,4.375 true 1.344,1.406 1.521,1.406 1.521,1.406 1.917,1.323 true 1.156,1.313 1.344,1.5 0.188,0.188 10 false *1 1.938,2.042 2.146,2.24 0.208,0.198 10 false *2 2.313,4.292 2.521,4.479 0.208,0.188 10 false *3 0.698,2.094 0.906,2.292 0.208,0.198 10 false *a 2.865,0.823 3.052,1.01 0.188,0.188 10 false *b
*1 Gasket
*2 Center Exhaust Pipe Assembly
*3 Exhaust Tailpipe Assembly
*a Gap Between Flanges
*b Wooden Block


Using a wooden block and hammer, gradually tap the gasket until it is flush with the end face of the center exhaust pipe assembly.

NOTICE:
·

Make sure to install the gasket in the correct direction.

·

Do not reuse the gasket.

·

Do not drop or otherwise damage the gasket.

·

Do not damage the sliding portion of the gasket.

·

Make sure to push the gasket by hand. Do not push in the gasket as you install the exhaust tailpipe assembly.




d.
A261473N02
0.885,2.385 1.042,2.583 0.156,0.198 10 true A 1.813,2.344 1.969,2.542 0.156,0.198 10 true A 1.792,0.125 1.948,0.323 0.156,0.198 10 true B 2.594,0.219 2.75,0.417 0.156,0.198 10 true B

Install the exhaust tailpipe assembly with 4 new nuts.

Torque:
Bolt A : 19 N*m (194 kgf*cm, 14 ft.*lbf)
Bolt B : 6.0 N*m (61 kgf*cm, 53 in.*lbf)


e.

Install the exhaust tailpipe assembly to the center exhaust pipe assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 16.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

Hide 17. CLEAR ENGINE HISTORY DATA USING ENGINE HISTORY UTILITY (PM Accumulation History Data)