Home › Engine / Hybrid System › N04C-VL (ENGINE MECHANICAL) › VALVE CLEARANCE › from 2019.08
RM2850E _51 Engine / Hybrid System _073160 N04C-VL ENGINE MECHANICAL _0356001 VALVE CLEARANCE N

N04C-VL ENGINE MECHANICAL  VALVE CLEARANCE  ADJUSTMENT  


PROCEDURE

Hide 51441D 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 23670 2.REMOVE INJECTOR ASSEMBLY

Hide 3.INSPECT VALVE CLEARANCE

a.
A146510C06
2.635,1.021 2.031,0.198 2.031,0.198 1.875,0.198 false 1.677,0.094 1.875,0.365 0.198,0.271 10 false *a
*a Timing Mark


Set the No. 1 cylinder to TDC/compression.

HINT:
·

Make sure that there is free play in the No. 1 cylinder rocker arms and that there is no free play in the No. 4 cylinder rocker arms.

·

If not, turn the crankshaft 1 revolution (360°) to set the No. 1 cylinder to TDC/compression.




b.
A462575

Check the valve clearance indicated in the illustration.

Standard Valve Clearance (Cold):
Item Specified Condition
Intake 0.3 mm (0.0118 in.)
Exhaust 0.45 mm (0.0177 in.)


NOTICE:

Do not apply excessive force to the valve adjusting screw.


HINT:

If the clearance is not as specified, record the measured value, and then adjust the valve clearance.



c.

Turn the crankshaft 360° to set the No. 4 cylinder to TDC/compression.

HINT:
·

Make sure that there is free play in the No. 4 cylinder rocker arms and that there is no free play in the No. 1 cylinder rocker arms.

·

If not, turn the crankshaft 1 revolution (360°) to set the No. 4 cylinder to TDC/compression.




d.
A462576

Check the valve clearance indicated in the illustration.

Standard Valve Clearance (Cold):
Item Specified Condition
Intake 0.3 mm (0.0118 in.)
Exhaust 0.45 mm (0.0177 in.)


NOTICE:

Do not apply excessive force to the valve adjusting screw.


HINT:

If the clearance is not as specified, record the measured value, and then adjust the valve clearance.



Hide 4.ADJUST VALVE CLEARANCE

a.
A151511C02
2.906,1.75 2.552,1.219 true 2.906,3.99 2.552,3.458 true 0.188,2.333 0.385,2.531 0.198,0.198 10 false *b 0.188,0.104 0.385,0.302 0.198,0.198 10 false *a 2.875,3.99 3.073,4.188 0.198,0.198 10 false *c 2.875,1.75 3.073,1.948 0.198,0.198 10 false *c
*a TDC of No. 1 and No. 4 Cylinder
*b TDC of No. 2 and No. 3 Cylinder
*c Timing Mark


Turn the crankshaft clockwise to align the timing mark on the crankshaft pulley with the pointer on the timing gear case.


b.
A462577C03
2.573,0.833 2.76,1.542 2.76,1.542 2.958,1.542 false 1.24,1.031 1.885,0.167 1.885,0.167 2.094,0.167 true 1.208,1.073 0.99,1.813 0.99,1.813 0.802,1.813 true 2.156,0.073 2.354,0.24 0.198,0.167 10 false *a 2.99,1.448 3.177,1.635 0.188,0.188 10 false *b 0.615,1.729 0.813,1.896 0.198,0.167 10 true *c
*a Adjusting Screw
*b Feeler Gauge
*c Lock Nut


With each piston positioned at TDC on the compression stroke, using a feeler gauge, adjust each valve clearance.

Standard Valve Clearance (Cold):
Item Specified Condition
Intake 0.3 mm (0.0118 in.)
Exhaust 0.45 mm (0.0177 in.)


HINT:

The feeler gauge should move with a very slight pull.



c.

Loosen the lock nut on the valve rocker arm and loosen the adjusting screw.


d.

Insert a 0.30 mm (0.0118 in.) feeler gauge for the intake valve or a 0.45 mm (0.0177 in.) feeler gauge for the exhaust valve between the adjusting screw on the valve rocker arm and the valve bridge.


e.

Turn the adjusting screw on the valve rocker arm until the feeler gauge slides with a very slight drag, and lock the adjusting screw with the lock nut.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



f.

Recheck the clearance.


Hide 23670 5.INSTALL INJECTOR ASSEMBLY

Hide 51441D 6.INSTALL NO. 1 ENGINE UNDER COVER