Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0327  Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)  P0328  Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)  P0332  Knock Sensor 2 Circuit Low Input (Bank 2)  P0333  Knock Sensor 2 Circuit High Input (Bank 2)  


DESCRIPTION

A flat type knock control sensor (non-resonant type) has a structure that can detect vibration between approximately 5 kHz and 15 kHz.

The knock control sensors are fitted onto the engine block to detect engine knocking.

The knock control sensor contains a piezoelectric element which generates a voltage when it becomes deformed.

The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No. DTC Detection Condition Trouble Area
P0327
P0332
Output voltage of knock sensor 1 or 2 is 0.5 V or less
(1 trip detection logic)
·

Short in knock sensor 1 or 2 circuit

·

Knock sensor 1 or 2

·

ECM


P0328
P0333
Output voltage of knock sensor 1 or 2 is 4.5 V or more
(1 trip detection logic)
·

Open in knock sensor 1 or 2 circuit

·

Knock sensor 1 or 2

·

ECM



HINT:

When any of DTCs P0327, P0328, P0332 and P0333 are set, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the engine switch is turned off.


Reference: Inspection using an oscilloscope

A395331E01
2.406,0.323 3,0.552 0.594,0.229 10 false 1 V/DIV. 2.667,0.99 3.208,1.219 0.542,0.229 10 false Ground 1.094,1.875 1.948,2.115 0.854,0.24 10 false 1 ms./DIV.

The correct waveform is as shown.

ECM Terminal Name Between KNK1 and EKNK, or KNK2 and EKN2
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

WIRING DIAGRAM

A387739E02
6.135,5.396 6.49,5.573 0.354,0.177 10 false ECM 0.625,0.531 0.854,0.708 0.229,0.177 10 false U2 3.5,1.302 3.813,1.479 0.313,0.177 10 false DU1 3.51,2.094 3.823,2.271 0.313,0.177 10 false DU1 3.5,3.677 3.813,3.854 0.313,0.177 10 false DU1 3.5,4.479 3.813,4.656 0.313,0.177 10 false DU1 0.625,0.698 2.115,0.875 1.49,0.177 10 false Knock Sensor (Bank 1) 0.615,2.844 0.833,3.021 0.219,0.177 10 false U1 0.615,3.01 2.104,3.188 1.49,0.177 10 false Knock Sensor (Bank 2) 5.552,1.302 5.75,1.479 0.198,0.177 10 false D1 5.552,2.094 5.75,2.271 0.198,0.177 10 false D1 5.552,3.688 5.75,3.865 0.198,0.177 10 false D1 5.552,4.49 5.75,4.667 0.198,0.177 10 false D1 5.823,1.188 6.208,1.365 0.385,0.177 10 false KNK1 5.552,1.094 5.74,1.271 0.188,0.177 10 false 95 4.604,0.677 5.188,0.854 0.583,0.177 10 false Shielded 5.823,1.979 6.24,2.156 0.417,0.177 10 false EKNK 5.552,1.896 5.74,2.073 0.188,0.177 10 false 94 5.854,3.573 6.24,3.75 0.385,0.177 10 false KNK2 5.521,3.479 5.771,3.656 0.25,0.177 10 false 118 5.854,4.365 6.26,4.542 0.406,0.177 10 false EKN2 5.521,4.271 5.771,4.448 0.25,0.177 10 false 117 0.729,1.177 0.844,1.354 0.115,0.177 10 false 1 1.875,1.177 1.99,1.354 0.115,0.177 10 false 2 3.604,1.083 3.719,1.26 0.115,0.177 10 false 2 3.604,1.885 3.719,2.063 0.115,0.177 10 false 1 3.604,3.479 3.719,3.656 0.115,0.177 10 false 4 3.604,4.271 3.719,4.448 0.115,0.177 10 false 3 0.729,3.542 0.844,3.719 0.115,0.177 10 false 1 1.875,3.542 1.99,3.719 0.115,0.177 10 false 2 4.604,3.021 5.188,3.198 0.583,0.177 10 false Shielded

CAUTION / NOTICE / HINT

HINT:
·

DTCs P0327 and P0328 are for the bank 1 knock control sensor circuit.

·

DTCs P0332 and P0333 are for the bank 2 knock control sensor circuit.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (KNOCK FEEDBACK VALUE)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine / Data List / All Data / Knock Feedback Value.


f.

Read the value while driving the vehicle.

OK:

The value changes.


HINT:
Malfunction does not occur Knock Feedback Value changes
Malfunctions occur Knock Feedback Value does not change

The Knock Feedback Value change can be confirmed by running the engine with a high load, for example, by activating the air conditioning system and racing the engine.




OK

NG

2.INSPECT ECM
2.INSPECT ECM
a.
U188415E01
0.603,1.066 0.922,1.225 0.319,0.159 10 DU1 0.526,1.324 1.029,1.470 0.503,0.147 10 Female

Disconnect the DU1 connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
DU1 female connector 2 - 1 Engine switch on (IG) 4.5 to 5.5 V
DU1 female connector 4 - 3 Engine switch on (IG) 4.5 to 5.5 V




OK

3.INSPECT KNOCK SENSOR

NG

5.CHECK HARNESS AND CONNECTOR (DU1 CONNECTOR - ECM)
3.INSPECT KNOCK SENSOR
a.

Inspect the knock control sensor (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>KNOCK SENSOR>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (DU1 CONNECTOR - KNOCK SENSOR)

NG

4.CHECK HARNESS AND CONNECTOR (DU1 CONNECTOR - KNOCK SENSOR)
a.

Disconnect the DU1 connector.


b.

Disconnect the knock sensor connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance (Check for open):
Tester Connection Condition Specified Condition
DU1 male connector 2 - U2-2 Always Below 1 Ω
DU1 male connector 1 - U2-1 Always Below 1 Ω
DU1 male connector 4 - U1-2 Always Below 1 Ω
DU1 male connector 3 - U1-1 Always Below 1 Ω


Standard resistance (Check for short):
Tester Connection Condition Specified Condition
DU1 male connector 2 or U2-2 - Body ground Always 10 kΩ or higher
DU1 male connector 1 or U2-1 - Body ground Always 10 kΩ or higher
DU1 male connector 4 or U1-2 - Body ground Always 10 kΩ or higher
DU1 male connector 3 or U1-1 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (DU1 CONNECTOR - ECM)
a.

Disconnect the DU1 connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance (Check for open):
Tester Connection Condition Specified Condition
DU1 female connector 2 - D1-95 (KNK1) Always Below 1 Ω
DU1 female connector 1 - D1-94 (EKNK) Always Below 1 Ω
DU1 female connector 4 - D1-118 (KNK2) Always Below 1 Ω
DU1 female connector 3 - D1-117 (EKN2) Always Below 1 Ω


Standard resistance (Check for short):
Tester Connection Condition Specified Condition
DU1 female connector 2 or D1-95 (KNK1) - Body ground Always 10 kΩ or higher
DU1 female connector 1 or D1-94 (EKNK) - Body ground Always 10 kΩ or higher
DU1 female connector 4 or D1-118 (KNK2) - Body ground Always 10 kΩ or higher
DU1 female connector 3 or D1-117 (EKN2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR