Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The crankshaft position sensor system consists of a crank angle sensor plate (crankshaft) and a pickup coil. The crank angle sensor plate has 34 teeth at 10° intervals (2 teeth are missing for detecting top dead center), and is installed on the crankshaft.

The crankshaft position sensor generates 34 signals per crankshaft revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection and ignition timing are controlled.

DTC No. DTC Detection Condition Trouble Area
P0335
·

No CKP sensor signal to ECM while cranking (1 trip detection logic)


·

No CKP sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic)


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft (crank angle sensor plate)

·

ECM


P0339 Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 seconds or more (1 trip detection logic):
(a) Engine speed 1000 rpm or higher.
(b) Starter signal off.
(c) 3 seconds or more have elapsed since starter signal switched from on to off.
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft (crank angle sensor plate)

·

ECM



A107148E18
1.635,2.865 2.396,3.063 0.76,0.198 10 false 20 ms./DIV. 0.156,0.885 0.844,1.083 0.688,0.198 10 false 5 V/DIV. 0.177,1.469 0.458,1.667 0.281,0.198 10 false NE 0.094,1.969 0.458,2.167 0.365,0.198 10 false VV1 3.01,1.49 3.344,1.688 0.333,0.198 10 false GND 3.01,2.083 3.344,2.281 0.333,0.198 10 false GND 3.01,2.479 3.344,2.677 0.333,0.198 10 false GND 0.094,2.365 0.458,2.563 0.365,0.198 10 false VV2 0.333,0.26 2.74,0.458 2.406,0.198 10 false VV1, VV2 and NE Signal Waveforms

Reference: Inspection using an oscilloscope.

HINT:
·

The correct waveforms as shown.

·

VV1+ and VV2+ stand for the VVT sensor (for intake camshaft) signal, and NE+ stands for the crankshaft position sensor signal.

·

Grounding failure of the shielded wire may cause a noisy waveform.



ECM Terminal Name Between NE+ and NE-
Between VV1+ and VV1-
Between VV2+ and VV2-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling


WIRING DIAGRAM

A122758E09
6.181,0.201 6.511,0.359 0.330,0.158 10 ECM 5.957,0.677 6.345,0.837 0.388,0.159 10 VCV1 5.639,0.502 5.906,0.667 0.267,0.165 10 115 5.674,0.691 5.872,0.830 0.198,0.139 10 D1 5.674,1.183 5.872,1.323 0.198,0.139 10 D1 5.674,1.653 5.872,1.792 0.198,0.139 10 D1 5.674,2.204 5.872,2.344 0.198,0.139 10 D1 5.674,2.697 5.872,2.836 0.198,0.139 10 D1 5.674,3.163 5.872,3.302 0.198,0.139 10 D1 5.674,4.125 5.872,4.264 0.198,0.139 10 D1 5.674,4.585 5.872,4.725 0.198,0.139 10 D1 5.674,5.461 5.872,5.600 0.198,0.139 10 D1 5.674,5.944 5.872,6.083 0.198,0.139 10 D1 5.674,6.413 5.872,6.553 0.198,0.139 10 D1 5.674,6.933 5.872,7.073 0.198,0.139 10 D1 5.674,7.416 5.872,7.556 0.198,0.139 10 D1 5.674,7.884 5.872,8.024 0.198,0.139 10 D1 5.957,1.168 6.330,1.327 0.373,0.159 10 VV1+ 5.685,0.992 5.861,1.157 0.176,0.165 10 69 5.957,1.63 6.299,1.789 0.342,0.159 10 VV1- 5.685,1.454 5.861,1.619 0.176,0.165 10 92 5.957,2.192 6.346,2.351 0.389,0.159 10 VCE1 5.643,2.016 5.902,2.182 0.259,0.165 10 114 5.957,2.681 6.328,2.840 0.371,0.159 10 EV1+ 5.685,2.505 5.861,2.670 0.176,0.165 10 68 5.957,3.143 6.299,3.302 0.342,0.159 10 EV1- 5.685,2.967 5.861,3.133 0.176,0.165 10 91 5.964,5.441 6.352,5.600 0.388,0.159 10 VCE2 5.964,5.931 6.337,6.091 0.373,0.159 10 EV2+ 5.684,5.755 5.860,5.921 0.176,0.165 10 66 5.964,6.393 6.306,6.553 0.342,0.159 10 EV2- 5.684,6.218 5.860,6.383 0.176,0.165 10 89 5.964,6.919 6.353,7.078 0.389,0.159 10 VCV2 5.642,6.743 5.902,6.908 0.259,0.165 10 113 5.964,7.404 6.332,7.563 0.368,0.159 10 VV2+ 5.684,7.228 5.860,7.393 0.176,0.165 10 67 5.964,7.866 6.330,8.026 0.366,0.159 10 VV2- 5.684,7.691 5.860,7.856 0.176,0.165 10 90 5.957,4.11 6.257,4.269 0.300,0.159 10 NE+ 5.635,3.934 5.888,4.099 0.252,0.165 10 110 5.957,4.57 6.257,4.730 0.300,0.159 10 NE- 5.649,4.395 5.915,4.560 0.266,0.165 10 111 5.649,5.267 5.915,5.432 0.266,0.165 10 112 4.614,7.516 4.722,7.687 0.108,0.171 10 1 4.614,7.983 4.722,8.154 0.108,0.171 10 2 3.596,7.747 3.704,7.918 0.108,0.171 10 3 3.573,6.293 3.681,6.464 0.108,0.171 10 3 3.762,7.647 3.989,7.796 0.227,0.150 10 VC 4.202,7.416 4.570,7.579 0.368,0.163 10 VVL+ 4.229,7.871 4.570,8.034 0.341,0.163 10 VVL- 0.46,7.095 0.757,7.260 0.297,0.165 10 D32 0.824,7.092 3.485,7.262 2.661,0.170 10 VVT Sensor (for Intake Camshaft (bank 2)) 4.614,1.277 4.722,1.448 0.108,0.171 10 1 4.614,1.744 4.722,1.915 0.108,0.171 10 2 3.596,1.508 3.704,1.679 0.108,0.171 10 3 3.762,1.408 3.989,1.557 0.227,0.150 10 VC 4.162,1.176 4.569,1.339 0.407,0.163 10 VVR+ 4.192,1.632 4.569,1.795 0.377,0.163 10 VVR- 0.46,0.855 0.757,1.020 0.297,0.165 10 D45 0.824,0.853 3.485,1.023 2.661,0.170 10 VVT Sensor (for Intake Camshaft (bank 1)) 4.628,6.038 4.736,6.209 0.108,0.171 10 1 4.628,6.505 4.736,6.676 0.108,0.171 10 2 2.946,4.222 3.054,4.393 0.108,0.171 10 1 2.946,4.689 3.054,4.860 0.108,0.171 10 2 3.776,6.169 4.071,6.318 0.296,0.150 10 VC2 4.277,5.938 4.570,6.100 0.294,0.163 10 EX+ 4.3,6.393 4.570,6.556 0.270,0.163 10 EX- 0.474,5.616 0.771,5.782 0.297,0.165 10 D31 0.838,5.614 3.642,5.784 2.804,0.170 10 VVT Sensor (for Exhaust Camshaft (bank 2)) 0.222,3.954 0.501,4.119 0.279,0.165 10 D37 0.222,4.12 1.942,4.289 1.721,0.170 10 Crankshaft Position Sensor 4.628,2.8 4.736,2.971 0.108,0.171 10 1 4.628,3.267 4.736,3.438 0.108,0.171 10 2 3.61,3.032 3.718,3.203 0.108,0.171 10 3 3.776,2.931 4.071,3.081 0.296,0.150 10 VC2 4.277,2.7 4.570,2.863 0.294,0.163 10 EX+ 4.3,3.155 4.570,3.318 0.270,0.163 10 EX- 0.474,2.379 0.771,2.544 0.297,0.165 10 D44 0.838,2.377 3.642,2.546 2.804,0.170 10 VVT Sensor (for Exhaust Camshaft (bank 1)) 4.205,3.794 4.301,3.944 0.096,0.150 10 * 1.357,8.228 2.054,8.384 0.698,0.156 10 *: Shielded

CAUTION / NOTICE / HINT

HINT:
·

After performing the inspection procedure for the crankshaft position sensor, if DTC P0335 is output again, check the following items related to the VVT sensor.

-

Installation condition of the VVT sensor

-

Installation condition of the camshaft

-

Connection of the VVT sensor connector


·

If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.

·

The engine speed can be checked by using the intelligent tester. To perform the check, follow the procedures below:

(a)

Connect the intelligent tester to the DLC3.

(b)

Start the engine.

(c)

Turn the tester on.

(d)

Enter the following menus: Powertrain / Engine / Data List / All Data / Engine Speed.


The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.


·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Engine Speed.


e.

Start the engine.


f.

Read the values displayed on the tester while the engine is running.

Standard:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the tester.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the tester remains zero (0), there may be an open or short in the crankshaft position sensor circuit.





OK

NG

2.INSPECT CRANKSHAFT POSITION SENSOR
2.INSPECT CRANKSHAFT POSITION SENSOR
a.

Inspect the crankshaft position (CKP) sensor (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the CKP sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance (Check for open):
Tester Connection Condition Specified Condition
D37-1 - D1-110 (NE+) Always Below 1 Ω
D37-2 - D1-111 (NE-) Always Below 1 Ω


Standard resistance (Check for short):
Tester Connection Condition Specified Condition
D37-1 or D1-110 (NE+) - Body ground Always 10 kΩ or higher
D37-2 or D1-111 (NE-) - Body ground Always 10 kΩ or higher




OK

4.CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)
a.
B319222E14
1.708,1.563 2.375,1.792 0.667,0.229 10 Clearance 0.469,1.781 0.781,1.979 0.313,0.198 10 OK 2.667,1.781 2.979,1.979 0.313,0.198 10 NG

Check the CKP sensor installation condition.

OK:

Sensor is installed correctly.




OK

5.CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

5.CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)
a.

Check the teeth of the sensor plate.

OK:

Sensor plate does not have any cracks or deformation.




OK

NG

REPLACE CRANKSHAFT POSITION SENSOR PLATE