Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  P0355  Ignition Coil "E" Primary / Secondary Circuit  P0356  Ignition Coil "F" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is output, check the No. 1 ignition coil assembly (No. 1 cylinder) circuit.

·

If DTC P0352 is output, check the No. 2 ignition coil assembly (No. 2 cylinder) circuit.

·

If DTC P0353 is output, check the No. 3 ignition coil assembly (No. 3 cylinder) circuit.

·

If DTC P0354 is output, check the No. 4 ignition coil assembly (No. 4 cylinder) circuit.

·

If DTC P0355 is output, check the No. 5 ignition coil assembly (No. 5 cylinder) circuit.

·

If DTC P0356 is output, check the No. 6 ignition coil assembly (No. 6 cylinder) circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM, for each cylinder ignition.

A256625E08
5.49,1.292 5.625,0.844 5.625,0.844 5.75,0.844 false 4.802,1.021 4.969,1.021 false 4.969,1.021 4.76,1.677 false 3.021,8 3.375,8.177 0.354,0.177 10 false ECM 0.313,1.979 2.063,2.156 1.75,0.177 10 false Crankshaft Position Sensor 0.354,4.083 2.031,4.26 1.677,0.177 10 false VVT Sensor 0.229,5.76 2.104,6.313 1.875,0.552 10 false Other Sensors (Engine Coolant Temperature Sensor, Throttle Position Sensor, etc.) 3.167,1.51 3.542,1.688 0.375,0.177 10 false IGT1 4.813,0.417 5.656,0.594 0.844,0.177 10 false from Battery 5.771,0.74 6.906,1.104 1.135,0.365 10 false No. 1 Ignition Coil Assembly 4.396,2.802 5.542,3.156 1.146,0.354 10 false No. 2 Ignition Coil Assembly 5.823,1.531 6.771,1.708 0.948,0.177 10 false No. 1 Cylinder 5.813,3.271 6.76,3.448 0.948,0.177 10 false No. 2 Cylinder 4.396,3.896 5.542,4.219 1.146,0.323 10 false No. 3 Ignition Coil Assembly 5.813,4.365 6.76,4.542 0.948,0.177 10 false No. 3 Cylinder 4.396,4.969 5.542,5.281 1.146,0.313 10 false No. 4 Ignition Coil Assembly 5.813,5.448 6.76,5.625 0.948,0.177 10 false No. 4 Cylinder 4.396,6.052 5.542,6.427 1.146,0.375 10 false No. 5 Ignition Coil Assembly 5.813,6.531 6.76,6.708 0.948,0.177 10 false No. 5 Cylinder 4.417,7.135 5.563,7.479 1.146,0.344 10 false No. 6 Ignition Coil Assembly 5.813,7.615 6.76,7.792 0.948,0.177 10 false No. 6 Cylinder 5.938,2.042 6.677,2.219 0.74,0.177 10 false Spark Plug 4.375,0.938 4.813,1.115 0.438,0.177 10 false Igniter 3.156,1.948 3.479,2.125 0.323,0.177 10 false IGF1 3.167,2.875 3.542,3.052 0.375,0.177 10 false IGT2 3.167,3.979 3.542,4.156 0.375,0.177 10 false IGT3 3.167,5.063 3.542,5.24 0.375,0.177 10 false IGT4 3.167,6.146 3.542,6.323 0.375,0.177 10 false IGT5 3.167,7.229 3.542,7.406 0.375,0.177 10 false IGT6

DTC No. DTC Detection Condition Trouble Area
P0351
P0352
P0353
P0354
P0355
P0356
No IGF signal to ECM while engine is running
(1 trip detection logic)
·

Ignition system

·

Open or short in IGF1 or IGT circuit (1 to 6) between ignition coil and ECM

·

No. 1 to No. 6 ignition coils

·

ECM



A140641E02
0.378,0.462 2.253,0.786 1.875,0.324 10 IGT and IGF Signal waveform 2.72,0.796 3.254,1.302 0.534,0.506 10 2 V/DIV. 1.171,2.697 1.921,2.839 0.749,0.141 10 20 ms./DIV. 0.105,1.157 0.438,1.356 0.333,0.199 10 CH1 0.129,1.986 0.447,2.142 0.319,0.156 10 CH2 2.902,1.654 3.264,1.825 0.362,0.170 10 GND 2.902,2.508 3.264,2.678 0.362,0.170 10 GND

Reference: Inspection using an oscilloscope.

While idling the engine, check the waveform between terminals IGT (1 to 6) and E1, IGF1 and E1 of the ECM connector.

ECM Terminal Name Between IGT (1 to 6) and E1
Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling


MONITOR DESCRIPTION

A393964E01
2.698,0.729 3.688,1.094 0.99,0.365 10 false IGT 2.719,1.156 3.708,1.521 0.99,0.365 10 false IGF 1.542,1.052 2.531,1.417 0.99,0.365 10 false ECM 3.865,1.042 4.854,1.406 0.99,0.365 10 false Igniter 5.021,0.865 6.01,1.229 0.99,0.365 10 false Ignition Coil 0.156,2.396 1.542,2.781 1.385,0.385 10 false Ignition Signal (IGT) 1.323,2.833 2.313,3.198 0.99,0.365 10 false Normal 1.094,3.25 2.083,3.615 0.99,0.365 10 false Malfunction 0.177,2.938 0.958,3.854 0.781,0.917 10 false Ignition Confirmation Signal (IGF) 3.198,3.781 4.188,4.146 0.99,0.365 10 false Circuit Open 4.708,4.281 5.698,4.646 0.99,0.365 10 false Time 4.375,0.24 5.365,0.604 0.99,0.365 10 false Ignition Coil

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and sets a DTC.

WIRING DIAGRAM

A387736E01
6.309,7.906 6.661,8.080 0.352,0.174 10 ECM 5.922,1.088 6.295,1.262 0.372,0.174 10 IGT1 5.688,0.845 5.873,1.019 0.185,0.174 10 40 5.719,2.073 5.903,2.247 0.185,0.174 10 38 5.698,3.321 5.882,3.496 0.185,0.174 10 36 5.707,4.613 5.891,4.787 0.185,0.174 10 39 5.709,5.825 5.894,5.999 0.185,0.174 10 37 5.706,7.117 5.890,7.291 0.185,0.174 10 35 5.618,4.963 5.891,5.137 0.274,0.174 10 106 3.177,1.59 4.614,1.764 1.437,0.174 10 D16 No. 1 Ignition Coil 3.397,0.919 3.604,1.093 0.206,0.174 10 +B 3.397,1.288 3.742,1.462 0.344,0.174 10 GND 3.996,0.919 4.345,1.093 0.349,0.174 10 IGT1 4.079,1.288 4.338,1.462 0.259,0.174 10 IGF 3.218,1.01 3.335,1.184 0.116,0.174 10 1 3.218,1.384 3.335,1.558 0.116,0.174 10 4 4.406,1.01 4.523,1.184 0.116,0.174 10 3 4.406,1.384 4.523,1.558 0.116,0.174 10 2 3.397,2.166 3.604,2.340 0.206,0.174 10 +B 3.397,2.535 3.742,2.709 0.344,0.174 10 GND 3.996,2.166 4.345,2.340 0.349,0.174 10 IGT3 4.079,2.535 4.338,2.709 0.259,0.174 10 IGF 3.218,2.257 3.335,2.431 0.116,0.174 10 1 3.218,2.631 3.335,2.805 0.116,0.174 10 4 4.406,2.257 4.523,2.431 0.116,0.174 10 3 4.406,2.631 4.523,2.805 0.116,0.174 10 2 3.397,3.427 3.604,3.601 0.206,0.174 10 +B 3.397,3.796 3.742,3.970 0.344,0.174 10 GND 3.996,3.427 4.345,3.601 0.349,0.174 10 IGT5 4.079,3.796 4.338,3.970 0.259,0.174 10 IGF 3.218,3.518 3.335,3.692 0.116,0.174 10 1 3.218,3.892 3.335,4.066 0.116,0.174 10 4 4.406,3.518 4.523,3.692 0.116,0.174 10 3 4.406,3.892 4.523,4.066 0.116,0.174 10 2 3.594,4.681 3.801,4.855 0.206,0.174 10 +B 3.594,5.05 3.939,5.224 0.344,0.174 10 GND 4.193,4.681 4.542,4.855 0.349,0.174 10 IGT2 4.276,5.05 4.535,5.224 0.259,0.174 10 IGF 3.415,4.772 3.532,4.946 0.116,0.174 10 1 3.415,5.146 3.532,5.320 0.116,0.174 10 4 4.603,4.772 4.720,4.946 0.116,0.174 10 3 0.451,0.91 0.567,1.084 0.116,0.174 10 A 4.603,5.146 4.720,5.320 0.116,0.174 10 2 3.594,5.935 3.801,6.109 0.206,0.174 10 +B 3.594,6.304 3.939,6.478 0.344,0.174 10 GND 4.193,5.935 4.542,6.109 0.349,0.174 10 IGT4 4.276,6.304 4.535,6.478 0.259,0.174 10 IGF 3.415,6.026 3.532,6.200 0.116,0.174 10 1 3.415,6.4 3.532,6.574 0.116,0.174 10 4 4.603,6.026 4.720,6.200 0.116,0.174 10 3 4.603,6.4 4.720,6.574 0.116,0.174 10 2 3.594,7.189 3.801,7.363 0.206,0.174 10 +B 3.594,7.558 3.939,7.732 0.344,0.174 10 GND 4.193,7.189 4.542,7.363 0.349,0.174 10 IGT6 4.276,7.558 4.535,7.732 0.259,0.174 10 IGF 3.415,7.28 3.532,7.454 0.116,0.174 10 1 3.415,7.653 3.532,7.828 0.116,0.174 10 4 4.603,7.28 4.720,7.454 0.116,0.174 10 3 4.603,7.653 4.720,7.828 0.116,0.174 10 2 3.381,5.355 4.817,5.529 1.437,0.174 10 D17 No. 2 Ignition Coil 3.177,2.856 4.637,3.030 1.460,0.174 10 D18 No. 3 Ignition Coil 3.381,6.607 4.829,6.781 1.448,0.174 10 D19 No. 4 Ignition Coil 3.177,4.095 4.637,4.270 1.460,0.174 10 D20 No. 5 Ignition Coil 3.381,7.868 4.841,8.042 1.460,0.174 10 D21 No. 6 Ignition Coil 5.922,5.168 6.301,5.342 0.378,0.174 10 IGF1 5.922,4.827 6.295,5.001 0.372,0.174 10 IGT2 5.922,2.318 6.295,2.492 0.372,0.174 10 IGT3 5.922,6.06 6.295,6.234 0.372,0.174 10 IGT4 5.922,3.585 6.295,3.759 0.372,0.174 10 IGT5 5.911,7.343 6.283,7.518 0.372,0.174 10 IGT6 6.029,7.906 6.381,8.080 0.352,0.174 10 D1

A159616E03
3.395,0.336 3.651,0.487 0.255,0.151 10 IG2 3.297,2.283 3.587,2.435 0.290,0.151 10 G58 4.81,2.536 5.170,2.687 0.360,0.151 10 IG2D 5.226,2.629 5.414,2.780 0.188,0.151 10 11 3.297,2.442 4.314,2.593 1.017,0.151 10 Main Body ECU 1.606,0.576 1.862,0.728 0.255,0.151 10 IG2 0.57,1.37 1.202,1.522 0.633,0.151 10 F/B BATT 0.57,2.076 1.151,2.227 0.582,0.151 10 FL MAIN 0.67,2.804 1.145,2.955 0.475,0.151 10 Battery 3.911,0.794 4.011,0.945 0.100,0.151 10 3 6.432,0.694 6.547,0.845 0.116,0.151 10 A 3.911,1.258 4.011,1.410 0.100,0.151 10 1 3.036,0.794 3.136,0.945 0.100,0.151 10 5 3.036,1.258 3.136,1.410 0.100,0.151 10 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).


PROCEDURE

1.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)
a.
U188224E02
1.333,1.104 0.875,0.969 false 2.125,1.083 2.469,0.865 false 0.854,0.344 2.375,0.552 1.521,0.208 10 false Ignition Coil Connector 2.5,1.042 3.146,1.208 0.646,0.167 9 false Front View 0.073,0.031 1.438,0.208 1.365,0.177 10 false Wire Harness Side: 1.073,1.521 1.354,1.688 0.281,0.167 10 false D16 1.594,1.844 1.875,2.01 0.281,0.167 10 false D20 2.115,1.854 2.396,2.01 0.281,0.156 10 false D21 1.583,1.531 1.865,1.688 0.281,0.156 10 false D17 2.104,1.531 2.375,1.688 0.271,0.156 10 false D18 1.073,1.854 1.354,2.021 0.281,0.167 10 false D19 0.635,0.875 0.833,1.042 0.198,0.167 10 false +B 2.521,0.74 2.844,0.896 0.323,0.156 10 false GND

Disconnect the ignition coil connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
D16-1 (+B) - Body ground Engine switch om (IG) 11 to 14 V
D17-1 (+B) - Body ground Engine switch om (IG) 11 to 14 V
D18-1 (+B) - Body ground Engine switch om (IG) 11 to 14 V
D19-1 (+B) - Body ground Engine switch om (IG) 11 to 14 V
D20-1 (+B) - Body ground Engine switch om (IG) 11 to 14 V
D21-1 (+B) - Body ground Engine switch om (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D16-4 (GND) - Body ground Always Below 1 Ω
D17-4 (GND) - Body ground Always Below 1 Ω
D18-4 (GND) - Body ground Always Below 1 Ω
D19-4 (GND) - Body ground Always Below 1 Ω
D20-4 (GND) - Body ground Always Below 1 Ω
D21-4 (GND) - Body ground Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance (Check for open):
Tester Connection Condition Specified Condition
D16-3 (IGT1) - D1-40 (IGT1) Always Below 1 Ω
D17-3 (IGT2) - D1-39 (IGT2) Always Below 1 Ω
D18-3 (IGT3) - D1-38 (IGT3) Always Below 1 Ω
D19-3 (IGT4) - D1-37 (IGT4) Always Below 1 Ω
D20-3 (IGT5) - D1-36 (IGT5) Always Below 1 Ω
D21-3 (IGT6) - D1-35 (IGT6) Always Below 1 Ω
D16-2 (IGF) - D1-106 (IGF1) Always Below 1 Ω
D17-2 (IGF) - D1-106 (IGF1) Always Below 1 Ω
D18-2 (IGF) - D1-106 (IGF1) Always Below 1 Ω
D19-2 (IGF) - D1-106 (IGF1) Always Below 1 Ω
D20-2 (IGF) - D1-106 (IGF1) Always Below 1 Ω
D21-2 (IGF) - D1-106 (IGF1) Always Below 1 Ω


Standard resistance (Check for short):
Tester Connection Condition Specified Condition
D16-3 (IGT1) or D1-40 (IGT1) - Body ground Always 10 kΩ or higher
D17-3 (IGT2) or D1-39 (IGT2) - Body ground Always 10 kΩ or higher
D18-3 (IGT3) or D1-38 (IGT3) - Body ground Always 10 kΩ or higher
D19-3 (IGT4) or D1-37 (IGT4) - Body ground Always 10 kΩ or higher
D20-3 (IGT5) or D1-36 (IGT5) - Body ground Always 10 kΩ or higher
D21-3 (IGT6) or D1-35 (IGT6) - Body ground Always 10 kΩ or higher
D16-2 (IGF) or D1-106 (IGF1) - Body ground Always 10 kΩ or higher
D17-2 (IGF) or D1-106 (IGF1) - Body ground Always 10 kΩ or higher
D18-2 (IGF) or D1-106 (IGF1)- Body ground Always 10 kΩ or higher
D19-2 (IGF) or D1-106 (IGF1) - Body ground Always 10 kΩ or higher
D20-2 (IGF) or D1-106 (IGF1) - Body ground Always 10 kΩ or higher
D21-2 (IGF) or D1-106 (IGF1) - Body ground Always 10 kΩ or higher




OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355 OR P0356)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355 OR P0356)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 6 cylinders).

NOTICE:

Do not change the location of the connectors.



f.

Perform a simulation test.


g.

Enter the following menus: Powertrain / Engine / DTC.


h.

Read the DTCs.

Result
Result Proceed to
Same DTC output A
Different ignition coil DTC output B



A

B