Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.

DTC No. DTC Detection Condition Trouble Area
P0705 (A) Any 2 or more signals of the following are ON simultaneously (2 trip detection logic):
·

P input signal

·

N input signal

·

R input signal

·

D input signal


(B) Any 2 or more signals of the following are ON simultaneously (2 trip detection logic):
·

NSW input signal

·

R input signal

·

D input signal


(C) Any of the following conditions is met for 2.0 sec. or more with the shift lever in the S position (2 trip detection logic):
·

NSW input signal

·

P input signal

·

N input signal

·

R input signal


(D) All switches are OFF simultaneously for NSW, P, R, N and D.
·

Short in park/neutral position switch assembly circuit

·

Park/Neutral position switch assembly

·

ST relay

·

Transmission control switch

·

ECM



WIRING DIAGRAM

A140667E15
1.625,0.385 1.833,0.563 0.208,0.177 10 false D4 1.625,0.552 4.167,0.698 2.542,0.146 10 false Park/Neutral Position Switch Assembly 2.781,0.896 2.979,1.094 0.198,0.198 10 false DL 2.781,1.375 3.01,1.552 0.229,0.177 10 false NL 2.792,2.125 3.01,2.313 0.219,0.188 10 false RL 2.781,2.646 2.979,2.833 0.198,0.188 10 false PL 2.833,3.135 2.969,3.313 0.135,0.177 10 false B 2.073,3.135 2.198,3.313 0.125,0.177 10 false L 1.885,3.135 1.979,3.302 0.094,0.167 10 false 9 3.063,3.135 3.177,3.344 0.115,0.208 10 false 4 3.063,2.625 3.177,2.813 0.115,0.188 10 false 3 3.063,2.135 3.219,2.302 0.156,0.167 10 false 2 3.063,1.594 3.229,1.771 0.167,0.177 10 false 8 3.073,1.083 3.229,1.25 0.156,0.167 10 false 7 1.906,1.896 2.031,2.083 0.125,0.188 10 false 1 2.063,1.698 2.313,1.865 0.25,0.167 10 false RB 0.021,1.646 0.74,2.177 0.719,0.531 10 false From GAUGE No. 2 Fuse 0.302,3.031 0.708,3.365 0.406,0.333 10 false To ST Relay 0.083,4.948 0.698,5.281 0.615,0.333 10 false From RH ECU-IG 1.552,4.229 1.76,4.427 0.208,0.198 10 false G9 1.552,4.385 3.354,4.531 1.802,0.146 10 false Transmission Control Switch 1.875,5.052 1.99,5.24 0.115,0.188 10 false 6 3.042,5.042 3.229,5.219 0.188,0.177 10 false 13 2.854,5.042 3.01,5.219 0.156,0.177 10 false S 2.052,5.042 2.26,5.229 0.208,0.188 10 false IG 5.719,1.01 5.917,1.156 0.198,0.146 10 false D1 5.719,1.51 5.917,1.656 0.198,0.146 10 false D1 5.719,2.021 5.917,2.167 0.198,0.146 10 false D1 5.719,2.531 5.917,2.677 0.198,0.146 10 false D1 5.719,3.042 5.917,3.188 0.198,0.146 10 false D1 5.708,3.698 5.896,3.854 0.188,0.156 10 false A7 5.708,4.938 5.896,5.094 0.188,0.156 10 false A7 6.052,0.604 6.604,1.115 0.552,0.51 10 false ECM 6.01,0.969 6.292,1.188 0.281,0.219 10 false D 5.99,1.5 6.146,1.667 0.156,0.167 10 false N 6,1.99 6.365,2.156 0.365,0.167 10 false R 6,2.531 6.146,2.688 0.146,0.156 10 false P 6,3.031 6.417,3.219 0.417,0.188 10 false NSW 5.99,3.688 6.323,3.844 0.333,0.156 10 false STA 6.021,4.948 6.25,5.135 0.229,0.188 10 false S 5.708,4.76 5.958,4.958 0.25,0.198 10 false 25 5.708,3.5 5.948,3.688 0.24,0.188 10 false 48 5.719,2.833 5.917,3 0.198,0.167 10 false 62 5.729,2.323 5.917,2.521 0.188,0.198 10 false 24 5.729,1.823 5.906,1.99 0.177,0.167 10 false 25 5.729,1.313 5.906,1.458 0.177,0.146 10 false 27 5.729,0.813 5.906,0.958 0.177,0.146 10 false 26

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may by discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Turn the engine switch off.


b.

Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine / Data List / All Data.


f.

Read the values displayed on the tester.

Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Shift SW Status (R Range) Park/Neutral position switch assembly status:
ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect
Shift SW Status (P Range) Park/Neutral position switch assembly status:
ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect
Shift SW Status (N Range) Park/Neutral position switch assembly status:
ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect
Shift SW Status (D Range) Park/Neutral position switch assembly status:
ON or OFF
·

ON: Shift lever in D or S

·

OFF: Shift lever not in D or S


When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect
Sports Mode Selection SW Transmission control switch status:
ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.
U188958E01
0.498,1.642 0.693,1.780 0.195,0.138 10 D4 0.92,2.243 1.174,2.414 0.254,0.171 10 RB 0.149,0.072 1.452,0.394 1.303,0.322 10 Wire Harness Side: 0.635,0.819 2.422,0.978 1.787,0.159 10 Park/Neutral Position Switch 1.408,2.216 2.091,2.374 0.683,0.159 10 Front View 1.646,1.737 1.196,2.299 false

Disconnect the park/neutral position switch assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D4-1 (RB) - Body ground Engine switch on (IG) 11 to 14 V




OK

2.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the ST relay from the engine room No. 1 relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (check for open):
Tester Connection Condition Specified Condition
D4-9 (L) - ST relay terminal 1 Always Below 1 Ω


Standard Resistance (check for short):
Tester Connection Condition Specified Condition
D4-9 (L) or ST relay terminal 1 - Body ground Always 10 kΩ or higher




OK

3.INSPECT ST RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ST RELAY

OK

4.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPLACE ST RELAY

4.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.

Remove the ST relay from the engine room No. 1 relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester connection Condition Specified Condition
ST relay terminal 2 - Body ground Always Below 1 Ω




OK

5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

6.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.
U189225E02
0.531,1.281 0.146,2.135 false 0.625,1.281 0.583,2.125 false 0.708,1.281 0.927,2.26 false 0.781,1.281 1.333,2.146 false 1.938,3.417 1.99,4.281 false 0.083,2.177 0.26,2.385 0.177,0.208 10 false P 0.885,2.271 1.021,2.448 0.135,0.177 10 false D 1.302,2.188 1.49,2.427 0.188,0.24 10 false N 0.521,2.156 0.656,2.313 0.135,0.156 10 false R 1.948,4.313 2.104,4.51 0.156,0.198 10 false S 2.063,2.104 2.76,2.26 0.698,0.156 10 false Front View 0.781,4.156 1.479,4.313 0.698,0.156 10 false Front View 1.135,2.583 2.177,2.729 1.042,0.146 10 false ECM Connector 0.063,0.073 1.385,0.281 1.323,0.208 10 false Wire Harness Side: 0.656,0.5 0.854,0.646 0.198,0.146 10 false D1 0.74,2.583 0.938,2.729 0.198,0.146 10 false A7

Disconnect the ECM connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Turn the engine switch on (IG), and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

Standard Voltage:
Connection Shift Lever Position Specified Condition
D1-24 (P) - Body ground P 11 to 14 V
Not in P Below 1 V
D1-27 (N) - Body ground N 11 to 14 V
Not in N Below 1 V
D1-25 (R) - Body ground R 11 to 14 V*
Not in R Below 1 V
D1-26 (D) - Body ground D and S 11 to 14 V
Not in D and S Below 1 V


HINT:

*: The voltage will drop slightly due to lighting up of the back up light.




OK

7.CHECK HARNESS AND CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR
a.
U189346E01
0.365,0.986 0.740,1.220 0.375,0.233 10 G9 2.129,0.204 2.417,0.400 0.288,0.195 10 IG 0.044,0 1.364,0.166 1.321,0.166 10 Wire Harness Side: 2.525,1.011 3.220,1.177 0.696,0.166 10 Front View 0.147,1.648 2.616,1.814 2.469,0.166 10 Transmission Control Switch Connector 2.082,0.966 2.198,0.389 false

Disconnect the transmission control switch connector of the shift lock control unit assembly.


b.

Turn the engine switch on (IG).


c.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G9-6 (IG) - Body ground Engine switch on (IG) 11 to 14 V




OK

8.INSPECT TRANSMISSION CONTROL SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT TRANSMISSION CONTROL SWITCH
a.
U189453E02
1.198,1.26 1.375,1.927 false 1.427,2.229 1.604,2.896 false 0.135,0.083 1.323,0.281 1.188,0.198 10 false Component Side: 0.885,0.542 2.677,0.75 1.792,0.208 10 false Transmission Control Switch 0.479,2 0.708,2.177 0.229,0.177 10 false G9 1.104,1.052 1.281,1.26 0.177,0.208 10 false IG 1.594,2.938 1.771,3.146 0.177,0.208 10 false S

Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Connection Shift Position Specified Condition
6 (IG) - 13 (S) S, ''+'' and ''-'' Below 1 Ω
Not in S, ''+'' and ''-'' 10 kΩ or higher




OK

9.CHECK HARNESS AND CONNECTOR (ECM - TRANSMISSION CONTROL SWITCH)

NG

REPLACE TRANSMISSION CONTROL SWITCH

9.CHECK HARNESS AND CONNECTOR (ECM - TRANSMISSION CONTROL SWITCH)
a.
U189225E02
0.531,1.281 0.146,2.135 false 0.625,1.281 0.583,2.125 false 0.708,1.281 0.927,2.26 false 0.781,1.281 1.333,2.146 false 1.938,3.417 1.99,4.281 false 0.083,2.177 0.26,2.385 0.177,0.208 10 false P 0.885,2.271 1.021,2.448 0.135,0.177 10 false D 1.302,2.188 1.49,2.427 0.188,0.24 10 false N 0.521,2.156 0.656,2.313 0.135,0.156 10 false R 1.948,4.313 2.104,4.51 0.156,0.198 10 false S 2.063,2.104 2.76,2.26 0.698,0.156 10 false Front View 0.781,4.156 1.479,4.313 0.698,0.156 10 false Front View 1.135,2.583 2.177,2.729 1.042,0.146 10 false ECM Connector 0.063,0.073 1.385,0.281 1.323,0.208 10 false Wire Harness Side: 0.656,0.5 0.854,0.646 0.198,0.146 10 false D1 0.74,2.583 0.938,2.729 0.198,0.146 10 false A7

Disconnect the ECM connectors.


b.

Disconnect the transmission control switch connectors.


c.

Turn the engine switch on (IG), and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

Standard Voltage:
Connection Shift Position Specified Condition
A7-25 (S) - Body ground S, "+" and "-" 11 to 14 V
Except S, "+" and "-" Below 1 V




OK

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the park/neutral position switch assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D4-4 (B) - D1-62 (NSW) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D4-4 (B) or D1-62 (NSW) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR