The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0705 | (A) Any 2 or more signals of the following are ON simultaneously (2 trip detection logic):
·
P input signal ·
N input signal ·
R input signal ·
D input signal (B) Any 2 or more signals of the following are ON simultaneously (2 trip detection logic): ·
NSW input signal ·
R input signal ·
D input signal (C) Any of the following conditions is met for 2.0 sec. or more with the shift lever in the S position (2 trip detection logic): ·
NSW input signal ·
P input signal ·
N input signal ·
R input signal (D) All switches are OFF simultaneously for NSW, P, R, N and D. |
·
Short in park/neutral position switch assembly circuit ·
Park/Neutral position switch assembly ·
ST relay ·
Transmission control switch ·
ECM |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may by discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the engine switch off.
Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data.
Read the values displayed on the tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Shift SW Status (R Range) | Park/Neutral position switch assembly status:
ON or OFF |
·
ON: Shift lever in R ·
OFF: Shift lever not in R |
When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect |
| Shift SW Status (P Range) | Park/Neutral position switch assembly status:
ON or OFF |
·
ON: Shift lever in P ·
OFF: Shift lever not in P |
When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect |
| Shift SW Status (N Range) | Park/Neutral position switch assembly status:
ON or OFF |
·
ON: Shift lever in N ·
OFF: Shift lever not in N |
When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect |
| Shift SW Status (D Range) | Park/Neutral position switch assembly status:
ON or OFF |
·
ON: Shift lever in D or S ·
OFF: Shift lever not in D or S |
When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect |
| Sports Mode Selection SW | Transmission control switch status:
ON or OFF |
·
ON: Shift lever in S, "+" or "-" ·
OFF: Shift lever not in S, "+" or "-" |
- |
Disconnect the park/neutral position switch assembly connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D4-1 (RB) - Body ground | Engine switch on (IG) | 11 to 14 V |
OK
NG
Disconnect the park/neutral position switch assembly connector.
Remove the ST relay from the engine room No. 1 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D4-9 (L) - ST relay terminal 1 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D4-9 (L) or ST relay terminal 1 - Body ground | Always | 10 kΩ or higher |
OK
NG
Inspect the ST relay (See page Engine / Hybrid System>2GR-FE STARTING>STARTER RELAY>ON-VEHICLE INSPECTION).
OK
NG
Remove the ST relay from the engine room No. 1 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified Condition |
|---|---|---|
| ST relay terminal 2 - Body ground | Always | Below 1 Ω |
OK
NG
Inspect the park/neutral position switch assembly (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).
OK
NG
(See pageDrivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL)
Disconnect the ECM connector.
Disconnect the park/neutral position switch assembly connector.
Turn the engine switch on (IG), and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.
| Connection | Shift Lever Position | Specified Condition |
|---|---|---|
| D1-24 (P) - Body ground | P | 11 to 14 V |
| Not in P | Below 1 V | |
| D1-27 (N) - Body ground | N | 11 to 14 V |
| Not in N | Below 1 V | |
| D1-25 (R) - Body ground | R | 11 to 14 V* |
| Not in R | Below 1 V | |
| D1-26 (D) - Body ground | D and S | 11 to 14 V |
| Not in D and S | Below 1 V |
*: The voltage will drop slightly due to lighting up of the back up light.
OK
NG
Disconnect the transmission control switch connector of the shift lock control unit assembly.
Turn the engine switch on (IG).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-6 (IG) - Body ground | Engine switch on (IG) | 11 to 14 V |
OK
NG
Disconnect the transmission control switch connector.
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Connection | Shift Position | Specified Condition |
|---|---|---|
| 6 (IG) - 13 (S) | S, ''+'' and ''-'' | Below 1 Ω |
| Not in S, ''+'' and ''-'' | 10 kΩ or higher |
OK
NG
Disconnect the ECM connectors.
Disconnect the transmission control switch connectors.
Turn the engine switch on (IG), and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.
| Connection | Shift Position | Specified Condition |
|---|---|---|
| A7-25 (S) - Body ground | S, "+" and "-" | 11 to 14 V |
| Except S, "+" and "-" | Below 1 V |
OK
NG
Disconnect the park/neutral position switch assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D4-4 (B) - D1-62 (NSW) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D4-4 (B) or D1-62 (NSW) - Body ground | Always | 10 kΩ or higher |
OK
NG