Refer to DTC P2120 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P2120).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P2121 | Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic):
1. Difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V. (learned value of accelerator off position) 2. Difference between VPA and VPA2 is greater than or equal to the specified value. |
·
Accelerator pedal sensor assembly ·
ECM |
The accelerator pedal position sensor has 2 (main and sub) sensor circuits. If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between the 2 sensor circuits and switches to fail-safe mode. In fail-safe mode, the functioning circuit is used to calculate the accelerator pedal opening angle to allow the vehicle to continue driving. If both circuits malfunction, the ECM regards the opening angle of the accelerator pedal as being fully closed. In this case, the throttle valve remains closed as if the engine is idling.
If a pass condition is detected and then the engine switch is turned off, the fail-safe operation stops and the system returns to normal.
Refer to DTC P2120 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P2120).
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P2121 is output | A |
| DTC P2121 and other DTCs are output | B |
If any DTCs other than P2121 are output, troubleshoot those DTCs first.
A
B
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.
Read the values displayed on the tester.
| Accelerator Pedal Operation | Accel Sensor Out No. 1 | Accel Sensor Out No. 2 |
|---|---|---|
| Fully Released | 0.5 to 1.1 V | 1.2 to 2.0 V |
| Fully Depressed | 2.6 to 4.5 V | 3.4 to 4.75 V |
NG
OK
Replace the accelerator pedal sensor assembly (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL).
NEXT
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) and turn the tester on.
Operate the accelerator pedal in accordance with the following procedure.
Enter the following menus: Powertrain / Engine / Data List / All Data / Accel Sens. No. 1 Volt %, and Accel Sens. No. 2 Volt %.
Slowly depress the accelerator pedal until Accel Sens. No. 1 Volt % is approximately 30% and Accel Sens. No. 2 Volt % is approximately 46%, then slowly release the accelerator pedal.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P2121 is output | A |
| DTC is not output | B |
A
B